Harbor Freight Tools 280 - Straight Line Air Sander Support and Manuals
Get Help and Manuals for this Harbor Freight Tools item
View All Support Options Below
Free Harbor Freight Tools 280 manuals!
Problems with Harbor Freight Tools 280?
Ask a Question
Free Harbor Freight Tools 280 manuals!
Problems with Harbor Freight Tools 280?
Ask a Question
Most Recent Harbor Freight Tools 280 Questions
Timing The Gear Set On Central Pneumatic 91773 Air File
(Posted by mop1960 6 months ago)
Are Their Any Timing Marks For When You Disassemble It ?
(Posted by ronquest440mopar 1 year ago)
Is There A Manual To Set The Time On A Straight Line Sander , Itook It A Part An
I after I put the sander back together it just doesent work right
I after I put the sander back together it just doesent work right
(Posted by lopezaochoa 8 years ago)
Popular Harbor Freight Tools 280 Manual Pages
User Manual - Page 1
... be reproduced in serious injury. REV 14f Copyright© 1997 by Harbor Freight Tools®. No portion of Harbor Freight Tools.
2-3/4″ X 17-1/2″ AIR INLINE SANDER
Model 00280
SET UP AND OPERATING INSTRUCTIONS
Visit our website at: http://www.harborfreight.com
Read this material before using this manual or any artwork contained herein may not be included. Due to...
User Manual - Page 2
...FUNCTIONAL DESCRIPTION 8
SPECIFICATIONS 8 COMPONENTS AND CONTROLS 8
INITIAL TOOL SET UP/ASSEMBLY��8
UNPACKING 8 AIR SUPPLY 8
OPERATING INSTRUCTIONS 10
TOOL SET UP 10
INSTALLING SANDPAPER 10
WORK PIECE AND WORK AREA SET UP 11
GENERAL OPERATING INSTRUCTIONS 11
USER-MAINTENANCE INSTRUCTIONS 12
CLEANING, MAINTENANCE, AND LUBRICATION 12
TROUBLESHOOTING 13
PARTS LIST 14...
User Manual - Page 3
..., fire, and injury to potential personal injury hazards. Watch what you to persons. Safety Alert Symbol and Signal Words
In this manual, on the labeling, and all the instructions before using tools, basic precautions should always be followed, including the following:
This is used to alert you are able to
a. It is able...
User Manual - Page 4
...Check for which the tool is designed.
Always wear hearing
protection when using . of moving parts, breakage of an accessory not intended for the specific tool model. Use of parts, and any other untrained... must be controlled with care. A tool is dangerous in the
shoes and a hard hat must be repaired.
If damaged, have the tool serviced before making any residual air pressure, ...
User Manual - Page 5
...replacement parts.
Tool service must be performed only by the manufacturer. SYMBOLS AND SPECIFIC SAFETY INSTRUCTIONS...INSTRUCTIONS. Use this instruction
gases are capable of explosion and
manual before sanding.
4. Service
a. When servicing a tool, use . Use only authorized parts...concerning Risk of injury to persons.
2. specific tool model, increases the risk of Respiratory Injury....
User Manual - Page 6
... related to these exposures varies, depending on the user. To reduce vibration, maintain tool as possible. Install an in-line shutoff valve to allow immediate control over the air supply in this manual cannot cover all accessories properly to the tool
do this product contain lead, a chemical
known to the State of your exposure...
User Manual - Page 7
Page 7 SAVE THESE INSTRUCTIONS.
Item 00280 For technical questions, please call 1-888-866-5797. that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator.
User Manual - Page 8
... questions, please call Harbor Freight Tools at stated maximum air pressure.
Air Compressor
Quick Coupler
Regulator with pressure gauge, oiler, in the following pages, refer to the Assembly Diagram near the end of this manual.
Note: For additional information regarding the parts listed in -line shutoff valve, and quick coupler for best service, as a power source...
User Manual - Page 9
... tool in -line shutoff valve between the compressor and the tool.
6.
pressure of controls.
5. Repair ...tool, but are not required. TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION: Do not install...tool is disconnected. refer to its off and detach the air supply, safely discharge any time. a ball valve because it to the air inlet of continual use.
2. Attach an air hose to set...
User Manual - Page 10
... or tamper with any problems are used with this manual. Hold in a way not specifically explained within this Inline Sander.
Center the Sander over the back side of the Sander with a screwdriver (sold separately) are found, do not use tool until repaired. Pull up or use , looking for damaged, loose, and missing parts.
Slide one end...
User Manual - Page 11
...detected, disconnect the air hose and repair before making contact with one area for...will present a hazard while working .
4. Install a sheet of tool oil. Move the Inline Sander along a... motion.
Work Piece and Work Area Set Up
1. Firmly grip the Handle (16...it, release the Trigger immediately.
8. General Operating Instructions
1. Identify the area you are sanding. Do ...
User Manual - Page 12
...'s oil level needs to the component manufacturers' instructions.
USER-MAINTENANCE INSTRUCTIONS
Procedures not specifically explained in this manual must be performed only by a qualified technician.
TO PREVENT EXPLOSION: Lubricate the tool only with specified lubricants. Performing routine maintenance on the air supply will allow the tool to operate more safely and will also reduce...
User Manual - Page 13
...6. Install in-line filter in Initial Set Up: Air Supply.
1.
Dirty, worn or damaged valve. 4. Housing heats during use .
2. Clean or replace valve assembly.
Blocked air inlet screen (if equipped).
4. Clean air inlet screen of buildup.
5. Incorrect lubrication or not enough lubrication.
6. performance
Follow all safety precautions whenever diagnosing or servicing the tool...
User Manual - Page 14
... HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. Item 00280
Page 14
For technical questions, please call 1-888-866-5797. PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY...
User Manual - Page 16
...Harbor Freight Tools Co.
We will either repair or replace... or that this warranty, the product or part must accompany the merchandise.
Some states do ...lack of our product. This warranty gives you specific legal rights and you . We shall in ... repairs or alterations outside our facilities, criminal activity, improper installation, normal wear and tear, or to us with a replacement. ...
Harbor Freight Tools 280 Reviews
We have not received any reviews for Harbor Freight Tools yet.