Haier HB3600VD1M22 Support and Manuals
Get Help and Manuals for this Haier item
View All Support Options Below
Free Haier HB3600VD1M22 manuals!
Problems with Haier HB3600VD1M22?
Ask a Question
Free Haier HB3600VD1M22 manuals!
Problems with Haier HB3600VD1M22?
Ask a Question
Most Recent Haier HB3600VD1M22 Questions
Popular Haier HB3600VD1M22 Manual Pages
User Manual - Page 1
Installation & Operation Manual Air Handler
13 SEER 2 3 4 5 Ton
WARNING WHEN THIS APPLIANCE IS INSTALLED IN AN ENCLOSED AREA, SUCH AS A GARAGE OR UTILITY ROOM, WITH ANY CARBON MONOXIDE PRODUCING DEVICES (i.e.
MODEL # HB
M20 HB
M22
MODEL # HB
V20 HB
V22
INSTALLATION DATE
The information contained in this booklet is subject to the unit for future reference. IN THE ABSENCE...
User Manual - Page 2
... of substantial fines.
INDEX
TOPIC
General Physical dimensions Replacement Parts Source Installation Requirements Air Flow Orientation Horizontal Left-Hand Instructions Refrigerant Tubing Condensate Removal Electrical Connections Thermostat Wiring Orifice Change Circulating Air Duct Blower Performance Start-up Regular Maintenance Model Number Explanation
PAGE
2 3 6 6 7 8 9 10 10 11 12 14...
User Manual - Page 6
... is designed for service or replacement must also be suitably guarded against such damage by similar means. REPLACEMENT PARTS SOURCE Replacement parts are available through local distributors.When ordering replacement parts, give the COMPLETE model and serial numbers shown on a base, the base must be considered without modification. This appliance can be installed in the vertical...
User Manual - Page 7
...page 6) Important: Remove the horizontal pan when unit is installed in unconditioned i.e. (Garage, Attic ) application, or downflow applications, and install insulation kit on vertical ( donut shape ) drain pan.
*Upflow Discharge *Air Handler is factory ready for Upflow & Horizontal Right Discharge Application for 3*4*5 as shown. *Air Handler is factory ready for Upflow & Horizontal Left Discharge...
User Manual - Page 8
... completely to over torque screws. Fig.2
8
Air flow
Secondary Knockout
Primary Knockout Traps must be placed in its left -hand side. Before setting up flowrator assembly for proper drainage by the installer and placed under the entire unit with the horizontal drain pan on the right lower service panel.
7) The Airhandler can now be...
User Manual - Page 9
... condensate drain line must be installed as a lubricant. Important: The evaporator coil is required. REFRIGERANT TUBING
Refrigerant tubing should be used not to over tighten the adapter at the tubing entrance to the air handler. To avoid damage that will... Styrofoam and certain types of these materials. A joint compound should be supported or routed to avoid undue stress.
User Manual - Page 10
..." air handlers installed without a heat kit.
10
The use of the unit.
Blower
running Over-current Motor
Ampacity 208/230 FLA
208/230
Blower Motor H.P.
1.2/1.2 15/15
0.9
1/8
2.5/2.5 15/15
2.0
1/3
3.3/3.3 15/15
2.6
1/2
4.4/4.4 15/15
3.5
1/2
5.0/5.0 15/15
4.0
3/4
WARNING A MEANS OF STRAIN RELIEF MUST BE INSTALLED TO THIS APPLIANCE AT THE ELECTRICAL SERVICE ENTRANCE...
User Manual - Page 11
...TO INDOOR
For detailed Thermostat, please connect FAN RELAY
CONTROL
corresponding terminal according to above
control specification. If need select the air supply mode, switch can be mechanical type or programmable type. HEAT HEAT PUMP COOLING
TO ... the indoor unit & heat pump outdoor unit at the same time no air supply mode.
Note: Thermostat C : COM. Above diagram: Outdoor Unit
...
User Manual - Page 12
... the following diagram 6.
R : AC24V
TERMOSTAT
Y : COMPRESSOR
G
Y
R
C
G : FAN
For detailed Thermostat, please connect corresponding terminal according to above control specification. Note: Thermostat C: COM. For Thermostat Control Environment-temperature and Air Conditioning open /stop , the wiring
diagram as shown diagram 4. Thermostat can adopt multi-connect switch or select...
User Manual - Page 13
...air ducts must be insulated and return ducts must be necessary to install a vapor barrier to the exterior of all supply ducts must be designed and installed as per local and/or national code.Refer to NFPA 90A & 90B and the National Environmental Systems Contractors Association Manual "K". When passing through an unconditioned space. FOLLOW THESE INSTRUCTIONS... must be replaced before any ...
User Manual - Page 14
...column dry coil w/ filter) 4% reduction for differences encountered in installations. This measurement should be varied by adjusting the blower speed tap as the
temperature rise. 6) Measure the actual supply...be installed to be increased or decreased it may be in place. 2) Start the unit in the heat mode. 3) Measure the return air temperature. 4) Measure the supply temperature. Model
Static...
User Manual - Page 15
... flammable vapors may cause serious personal injury or death. Unit is installed, when necessary, and pitched to allow for drainage. A certified service technician should be maintained on a regular basis by the user is to insure that the circulating air filter(s) is cleaned or replaced. Drain pans and drain tubing were leak checked with water...
Haier HB3600VD1M22 Reviews
We have not received any reviews for Haier yet.