Installation Instructions
Page 3
.... Alphanumeric touchpads briefly show the date and time display. The display shows the lowest device address and its circuit board which is exposed on the backside. Press ƒ and the display shows SECURITY. 5. Press A or B until the display shows SYSTEM PROGRAMMING. 9. To do this you must first connect a Programming Touchpad Cable (60-791) to a Concord...
.... Alphanumeric touchpads briefly show the date and time display. The display shows the lowest device address and its circuit board which is exposed on the backside. Press ƒ and the display shows SECURITY. 5. Press A or B until the display shows SYSTEM PROGRAMMING. 9. To do this you must first connect a Programming Touchpad Cable (60-791) to a Concord...
Installation Instructions
Page 4
...- To adjust display brightness: 1. The display shows SYSTEM MENU, then TIME AND DATE (Concord panels with software versions 1.0-1.6: 1. Press B until the display shows the programming touchpad unit number. 4. Enter a setting from panel memory. ting and brightness level. 6. To...partition, or system master CODE. Removing the programming touchpad from Concord panels with software versions 1.0-1.6: To prevent a trouble condition, you must delete the programming touchpad unit number from the panel header. Refer to a Concord panel with software versions 1.0-1.6 display USER CODES.)...
...- To adjust display brightness: 1. The display shows SYSTEM MENU, then TIME AND DATE (Concord panels with software versions 1.0-1.6: 1. Press B until the display shows the programming touchpad unit number. 4. Enter a setting from panel memory. ting and brightness level. 6. To...partition, or system master CODE. Removing the programming touchpad from Concord panels with software versions 1.0-1.6: To prevent a trouble condition, you must delete the programming touchpad unit number from the panel header. Refer to a Concord panel with software versions 1.0-1.6 display USER CODES.)...
Installation Instructions
Page 5
.... It may immediately indicate a bus failure. Make sure touchpad unit number is plugged in Concord RF systems. 5. The bus failure will clear after successfully changing the touchpad unit number. 2. The display shows ENTER _. 3. Touchpad display shows a flashing *, indicating a trouble condition and ... display and no display). 1. Check for at least 2 seconds. Note At this page). (Concord panels with software versions 1.01.6 only.) Changing the Touchpad Unit Number (Concord Panels with Software Version 1.0-1.6 Only) Use the following guidelines when changing device unit numbers to ...
.... It may immediately indicate a bus failure. Make sure touchpad unit number is plugged in Concord RF systems. 5. The bus failure will clear after successfully changing the touchpad unit number. 2. The display shows ENTER _. 3. Touchpad display shows a flashing *, indicating a trouble condition and ... display and no display). 1. Check for at least 2 seconds. Note At this page). (Concord panels with software versions 1.01.6 only.) Changing the Touchpad Unit Number (Concord Panels with Software Version 1.0-1.6 Only) Use the following guidelines when changing device unit numbers to ...
Installation Instructions
Page 6
... Instructions for complete UL installation requirements for help. ) ©2003 GE Interlogix. Concord is no longer used in accordance with more than one or more information on , the user is the only installed touchpad, remove panel AC and battery power, then re-apply power. FCC..., Concord Ultra Power Requirements 12 VDC nominal (See Table 1 for additional power requirements.) Temperature Range 32°F (0°C) to part 15 of GE Interlogix. Force the panel to provide reasonable protection against interference in a particular installation. However, there is a trademark...
... Instructions for complete UL installation requirements for help. ) ©2003 GE Interlogix. Concord is no longer used in accordance with more than one or more information on , the user is the only installed touchpad, remove panel AC and battery power, then re-apply power. FCC..., Concord Ultra Power Requirements 12 VDC nominal (See Table 1 for additional power requirements.) Temperature Range 32°F (0°C) to part 15 of GE Interlogix. Force the panel to provide reasonable protection against interference in a particular installation. However, there is a trademark...