Garmin GT41-TH Support and Manuals
Get Help and Manuals for this Garmin item
This item is in your list!
View All Support Options Below
Free Garmin GT41-TH manuals!
Problems with Garmin GT41-TH?
Ask a Question
Free Garmin GT41-TH manuals!
Problems with Garmin GT41-TH?
Ask a Question
Popular Garmin GT41-TH Manual Pages
Installation Instructions - Page 1
... one of the first step. NOTE: In order for the software update instructions to www.garmin.com/support for in
Á front of the water beneath your vessel. NOTE...> Finish. Thru-Hull Transducer
Installation Instructions
Important Safety Information
WARNING See the Important Safety and Product Information guide in Taiwan
190-01774-02_0B The device must copy the software update to a memory...
Installation Instructions - Page 2
...install the transducer. The wood becomes a cutting guide for increased sonar accuracy. Drilling the Transducer Stem Hole and the Anti-Rotation Bolt Holes in a Cored Fiberglass Hull... a piece of your vessel. Cored Fiberglass Boat Hull Installation Instructions
Thru-Hull Transducer in a Cored Hull with displacement hulls , the transducer should
be
mounted
approximately
1/3
aft
of
Å...
Installation Instructions - Page 3
...
à epoxy to set thoroughly. 8 While holding a 25 mm (1 in a cored fiberglass hull, avoid over the transducer. Apply marine sealant around...instructions if you are installed on the transducer. The holes must contact the hull.
5 Apply marine sealant to your transducer,
À remove them. 2 Apply marine sealant at least one inside the hull, slide the backing block onto the transducer...
Installation Instructions - Page 4
... using a fairing block to mount the transducer on the transducer.
Installing the Transducer with a Fairing Block It is recommended that two installers complete these instructions, with a 9 mm (3/8 in a Non-cored/Fiberglass Hull with one positioned outside the hull. Applying Marine Sealant to a Thru-Hull Transducer You must cut a hole from outside the hull at the stem hole
location, from...
Installation Instructions - Page 5
... Block It is recommended that two installers complete these instructions if you can mount the device without a Fairing Block If the deadrise angle of the backing block that Ã
must apply marine sealant to the transducer to ensure a tight, waterproof seal between the fairing block and the hull.
2 Apply marine sealant at least one...
Installation Instructions - Page 6
... to the anti-rotation bolts and
À
Á
transducer stem .
Â
Metal Boat Hull Installation Instructions
Thru-Hull Transducer in a Metal Hull with a Fairing Block If the deadrise angle of your mounting location exceeds 5°, you should follow these instructions when you are using a fairing block to mount the transducer on the transducer.
2 From outside the hole. Do not over...
Installation Instructions - Page 7
... and Anti-Rotation Bolt Holes Using a Template
WARNING The device must complete all other installation instructions. NOTE: When installing a transducer in .) hole saw, cut the stem hole from outside the hull.
6 Using a 32 mm (1 1/4 in an aluminum or steel hull, you must use the included isolation plate.
1 Secure the bushings to your vessel.
Failure to do...
Installation Instructions - Page 8
...: Never apply ketone-based anti-fouling paint to the hull of Garmin.
© 2014-2015 Garmin Ltd. Cleaning the Transducer Aquatic fouling accumulates quickly and can affect a vessel's performance...hulls and to slow the growth of organisms that were added below the water line.
or its subsidiaries, registered in the USA and other countries. or its subsidiaries
www.garmin.com/support...
Garmin GT41-TH Reviews
Do you have an experience with the Garmin GT41-TH that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Garmin yet.
Earn 750 points for your review!