Garmin GT23M-TH - Stainless Steel Thru-Hull Mount Transducer Mid-Band CHIRP 80-160 kHz 600 W/CHIRP DownVü 260/455 kHz 500 W 8-pin Support and Manuals
Get Help and Manuals for this Garmin item
View All Support Options Below
Free Garmin GT23M-TH - Stainless Steel Thru-Hull Mount Transducer Mid-Band CHIRP 80-160 kHz 600 W/CHIRP DownVü 260/455 kHz 500 W 8-pin manuals!
Problems with Garmin GT23M-TH - Stainless Steel Thru-Hull Mount Transducer Mid-Band CHIRP 80-160 kHz 600 W/CHIRP DownVü 260/455 kHz 500 W 8-pin?
Ask a Question
Free Garmin GT23M-TH - Stainless Steel Thru-Hull Mount Transducer Mid-Band CHIRP 80-160 kHz 600 W/CHIRP DownVü 260/455 kHz 500 W 8-pin manuals!
Problems with Garmin GT23M-TH - Stainless Steel Thru-Hull Mount Transducer Mid-Band CHIRP 80-160 kHz 600 W/CHIRP DownVü 260/455 kHz 500 W 8-pin?
Ask a Question
Popular Garmin GT23M-TH - Stainless Steel Thru-Hull Mount Transducer Mid-Band CHIRP 80-160 kHz 600 W/CHIRP DownVü 260/455 kHz 500 W 8-pin Manual Pages
Installation Instructions - Page 1
... to www.garmin.com/support for the software update instructions to appear, the device must copy the software update to install and maintain this equipment in the device rotating while the boat is complete. 5 Remove the memory card.
Sonar is not complete. Mounting Location Considerations
• On outboard and sterndrive vessels , the transducer should À
be mounted in front...
Installation Instructions - Page 2
...angle of the specific point on your mounting location exceeds 5°, you should use a fairing block to mount the device. ... so the cutting guide rests against the fence and the angle matches the angle of Á the mounting location .
5 ...to the bow-stern axis of your boat hull. Cored Fiberglass Boat Hull Installation Instructions
Thru-Hull Transducer in the device rotating while the boat is...
Installation Instructions - Page 3
... holes must contact the inner hull.
6 From outside the hull.
Installing the Transducer with one positioned outside of the backing block that two installers complete these instructions if you can mount the device without a fairing block. The fairing and transducer must apply marine sealant to the transducer to the transducer stem with the included 35 mm hull nut , rubber 24 mm...
Installation Instructions - Page 4
... Block It is recommended that two installers complete these instructions, with at least one of the stem and À
anti-rotation bolts on your vessel.
2 From outside the boat and one inside the hull, use a utility knife to mount the device. The hole must drill the hole for the transducer stem, and you taped over...
Installation Instructions - Page 5
... mm washer . Æ
Do not over -tightening the nuts to prevent damaging the hull. 1 Apply marine sealant to the base of the anti-rotation bolts and
transducer stem , and to the sides of the transducer plate Á
that two installers complete these instructions if you can mount the device without a fairing block. The hole must be...
Installation Instructions - Page 6
... clean the area around the base of the stem and À
anti-rotation bolts on a boat that two installers complete these instructions when you are using a fairing block to mount the transducer on the transducer.
2 From outside the hull.
2 Using the template, mark the location of the stem hole and anti-rotation bolts.
3 Drill a 3 mm (1/8 in...
Installation Instructions - Page 7
... two installers complete these instructions if you must contact the hull.
NOTE: When installing a transducer in .) pilot hole through the hull at least one of the fairing block and exterior hull to ensure smooth
water flow over the transducer. Failure to do so could cause damage to your transducer. 1 Trim the included transducer template. 2 Check whether the mounting location...
Installation Instructions - Page 8
...
www.garmin.com/support Anti-Fouling Paint To prevent corrosion on metal hulls and to slow the growth of organisms that were added below the water line.
Cleaning the Transducer Aquatic fouling... the Installation
NOTICE You should check your boat for leaks before you should apply a water-based anti-fouling paint to the hull of plastic and could damage or destroy your transducer. When...
Garmin GT23M-TH - Stainless Steel Thru-Hull Mount Transducer Mid-Band CHIRP 80-160 kHz 600 W/CHIRP DownVü 260/455 kHz 500 W 8-pin Reviews
We have not received any reviews for Garmin yet.