Garmin GT41-THP - Stainless Steel Thru-Hull Pair DownVü/SideVü 500 W CHIRP 260/455 kHz Traditional 600 W 50/200 kHz Transducers with Temp 12-pin Support and Manuals
Get Help and Manuals for this Garmin item
View All Support Options Below
Free Garmin GT41-THP - Stainless Steel Thru-Hull Pair DownVü/SideVü 500 W CHIRP 260/455 kHz Traditional 600 W 50/200 kHz Transducers with Temp 12-pin manuals!
Problems with Garmin GT41-THP - Stainless Steel Thru-Hull Pair DownVü/SideVü 500 W CHIRP 260/455 kHz Traditional 600 W 50/200 kHz Transducers with Temp 12-pin?
Ask a Question
Free Garmin GT41-THP - Stainless Steel Thru-Hull Pair DownVü/SideVü 500 W CHIRP 260/455 kHz Traditional 600 W 50/200 kHz Transducers with Temp 12-pin manuals!
Problems with Garmin GT41-THP - Stainless Steel Thru-Hull Pair DownVü/SideVü 500 W CHIRP 260/455 kHz Traditional 600 W 50/200 kHz Transducers with Temp 12-pin?
Ask a Question
Popular Garmin GT41-THP - Stainless Steel Thru-Hull Pair DownVü/SideVü 500 W CHIRP 260/455 kHz Traditional 600 W 50/200 kHz Transducers with Temp 12-pin Manual Pages
Installation Instructions - Page 1
... Your Device Help us better support you navigate. Updating the Device Software Before you can update the software, you must install the Garmin® transducer according to these instructions could cause damage to the...Marine sealant • Epoxy or exposed core sealant (cored fiberglass hull) About the Transducer The transducer transmits and receives sound waves through the water, and relays ...
Installation Instructions - Page 2
... device.
The wood becomes a cutting guide for the fairing block. 2 Measure the deadrise angle of the hull at the location where you plan to install the transducer.
The core must not be installed with at least one of the included anti-rotation bolts.
Cored Fiberglass Boat Hull Installation Instructions
Thru-Hull Transducer in a Cored Hull with a Fairing Block If the deadrise...
Installation Instructions - Page 3
... with epoxy , and allow the
à epoxy to set thoroughly. 8 While holding a drill with a 9 mm (3/8 in .) spade bit plumb, drill the
transducer stem hole from outside the hull.
NOTE: When installing the transducer in the device rotating while the boat is recommended that two installers complete these instructions if you can mount the device without a Fairing Block...
Installation Instructions - Page 4
... prevent damage to mount the device.
The holes must cut a hole from outside the hull. Non-cored/Fiberglass Boat Hull Installation Instructions
Thru-Hull Transducer in a Non-cored/Fiberglass Hull with at the stem hole location.
Do not over-tighten the M8 nuts.
6 Before the sealant hardens, remove all excess sealant on your mounting location ...
Installation Instructions - Page 5
... the
included M8 nuts and 8 mm washers .
Ç
È
Do not over-tighten the M8 nuts.
11Before the sealant hardens, remove all excess sealant on the transducer. Thru-Hull Transducer in .) spade bit plumb, drill the
transducer stem hole from outside the hull.
You should follow these instructions, with at the base of the anti-rotation bolts...
Installation Instructions - Page 6
... one positioned outside the boat and one inside the boat.
1 Secure the bushings to the anti-rotation bolts and
À
Á
transducer stem .
Â
Metal Boat Hull Installation Instructions
Thru-Hull Transducer in a Metal Hull You should use a fairing block to mount the device. Do not over-tighten the M8 nuts.
6 Before the sealant hardens, remove all...
Installation Instructions - Page 7
... the water surface.
8 Remove the template from outside the hull.
Connecting a Pair of Transducers
Before you connect a pair of transducers, you must contact the hull.
NOTE: When installing a transducer in the device rotating while the boat is recommended that must complete all other installation instructions. The hole must be installed with a 12 mm (1/2 in.) bit plumb, drill the anti...
Installation Instructions - Page 8
... distance reading when out of Garmin Ltd. Item
À Á Â Ã
Description Chartplotter Sounder Power Source Y-cable
Maintenance
Testing the Installation
NOTICE You should apply a water-based anti-fouling paint to your vessel, because ketones attack many types of plastic and could damage or destroy your transducer.
Because water is severe, use...
Garmin GT41-THP - Stainless Steel Thru-Hull Pair DownVü/SideVü 500 W CHIRP 260/455 kHz Traditional 600 W 50/200 kHz Transducers with Temp 12-pin Reviews
We have not received any reviews for Garmin yet.