Garmin GMR 6kW Pedestal xHD Support and Manuals
Get Help and Manuals for this Garmin item
View All Support Options Below
Free Garmin GMR 6kW Pedestal xHD manuals!
Problems with Garmin GMR 6kW Pedestal xHD?
Ask a Question
Free Garmin GMR 6kW Pedestal xHD manuals!
Problems with Garmin GMR 6kW Pedestal xHD?
Ask a Question
Popular Garmin GMR 6kW Pedestal xHD Manual Pages
Declaration of Conformity - Page 1
... Olathe, Kansas 66062 U.S.A
GARMIN Corporation No. 68, Jangshu 2nd Rd., Shijr, Taipei County, TAIWAN, R.O.C.
Liberty House, Hounsdown Business Park, Southampton, Hampshire, SO40 9LR, U.K. Techniques for craft not in the Out-of-Band Domain
ITU-RM.1177 Unwanted Emissions - Performance requirements methods of Equipment: Model Number(s):
Marine Radar
GMR 60X GMR 120X
(X may be any...
Installation Instructions - Page 1
... tool and die set or compatible equivalent
December 2010
190-01266-02 Rev. If any parts are the most sensitive part of the radar and withstand any questions while installing your GMR 400/600/1200 xHD radar. Notice: When drilling or cutting, always check the opposite side of a professional installer, or contact Garmin® Product Support. Keep the original...
Installation Instructions - Page 2
...a minimal part of SSB radios, the distance should be increased to install the GMR 400/600/1200 xHD radar, ...location to 7 ft. (2 m).
2
GMR 400/600/1200 xHD Installation Instructions For vessels with the water line. • Garmin recommends mounting the radar out of range ... in the path of the radar beam may be sturdy enough to support the weight of a radar beam. A radar beam can lower the...
Installation Instructions - Page 3
.../1200 xHD Installation Instructions
Figure 5
Figure 6
flat washer spring washer M10 hex nut
3 Ensure it is pointed toward the bow.
Installing the Mounting Studs and Seals
1. Use a 5 mm Allen wrench to 180° (Figure 4). Tighten the mounting studs until they bottom out in the pedestal matching the hole pattern that you are using a pre-drilled Garmin...
Installation Instructions - Page 4
... network connector (included) to the pedestal using .
If this is needed (see page 8).
4
GMR 400/600/1200 xHD Installation Instructions Verify that you are extended, use the appropriate tie-wraps, fasteners, and sealant to other equipment. Secure the antenna to create a custom-length Garmin Marine Network cable if needed to supply a specific constant voltage to shrink it...
Installation Instructions - Page 5
...output cable (red and black) using an 8 gauge copper cable (not included).
GMR 400/600/1200 xHD radar
To water ground
Garmin marine network cable Radar power cable 7.5 A fuse
Power converter
+ 10-40 Vdc ...the in-line fuse holder. and 1206)
To RF ground
Power Wiring Diagram
GMR 400/600/1200 xHD Installation Instructions
5 Connect the radar to cut the radar power cable, you choose to...
Installation Instructions - Page 6
... Network
For a stand-alone network (chartplotter and radar only), attach the RJ-45 marine network cable to the appropriate installation instructions.
6
GMR 400/600/1200 xHD Installation Instructions NOTE: Every device connected to the Garmin Marine Network must be connected to the power supply for other network components. These diagrams show the power connections. Wire each device...
Installation Instructions - Page 7
... Offset = 180°
bow stern
GMR 400/600/1200 xHD Installation Instructions
7 Download the latest software from www.garmin.com.
Using the ROCKER, highlight the Advanced tab, then the Antenna Size field, and press ENTER. 4. From the Radar page, press the Setup softkey to 180° and test the radar. Set the Front of Boat Offset slider...
Installation Instructions - Page 8
... avoid damaging the copper tape.
8
GMR 400/600/1200 xHD Installation Instructions Position
1 2 3 4 5 6... 7 8
Wire Color-Main/Stripe
Side A
Side B
White/Orange
White/Green
Orange
Green
White/Green
White/Orange
Blue
Blue
White/Blue
White/Blue
Green
Orange
White/Brown
White/Brown
Brown
Brown
Position 8 Position 1
NOTE: The Garmin...
Installation Instructions - Page 9
... Plug Hand Tool and Die Set (or compatible equivalent), crimp the plug onto the wires following the recommended procedure of the crimp-tool manufacturer.
3. Be careful not to verify proper order before continuing. The cable is securely seated in the cable-connection housing. O-Ring
GMR 400/600/1200 xHD Installation Instructions
9
Visually inspect the wires...
Installation Instructions - Page 11
... to 10 MARPA targets for sea clutter.
Specifications
Pedestal (Physical)
Weight: 45.9 lb. (20...Dual Range Mode: Simultaneous operation of two ranges displayed in . (15 m) long
GMR 400/600 xHD
Transmit Power: GMR 400 xHD: 4 kW Transmit Power: GMR 600 xHD...manual or auto (AFC) receiver tuning; Radar/Chart Overlay: Overlay mode is required)
GMR 400/600/1200 xHD Installation Instructions
11
Installation Instructions - Page 12
... while using this guide, and that interference will not occur in the unit only to facilitate, not to replace, the use of the following potentially hazardous situations could result in an accident or collision resulting in accordance with the instructions, may damage your Garmin product: www.garmin.com.
12
GMR 400/600/1200 xHD Installation Instructions WARNING: This product...
Installation Instructions - Page 13
.... 886/2.2642.9199 Fax 886/2.2642.9099
GMR 400/600/1200 xHD Installation Instructions
13 Limited Warranty
All Garmin marine radomes and open array radomes are warranted to any country in Garmin. This product is provided by the local in the area of intended distribution. Garmin makes no charge to repair or replace the unit or software or offer...
Installation Instructions - Page 14
... the express prior written consent of this and other electronic storage medium to be used without notice.
GMR™ and myGarmin™ are trademarks of this manual onto a hard drive or other Garmin products. B
Printed in this manual may not be viewed and to change without the express permission of Furuno Electric Co., Ltd...
Garmin GMR 6kW Pedestal xHD Reviews
We have not received any reviews for Garmin yet.