Fluke 707Ex Support and Manuals
Get Help and Manuals for this Fluke item
Popular Fluke 707Ex Manual Pages
Fluke 705, 707, 707Ex, and 715 Loop Calibrator Datasheet - Page 1
.../mA Calibrator
For more information, go to 10 V mA or % No No 18 hours typical, at the same time without carrying a DMM
• 0-20 mA or 4-20 mA default start up modes. Fluke 707 and 705 Two powerful models to a screeching halt.
Troubleshooting process loops Application Note (Literature code 1989137) In process systems, problems with simultaneous
current measurement
Specifications...
Fluke 707ex Users Manual - Page 1
Printed in USA All product names are trademarks of their respective companies.
®
707Ex mA Calibrator
Users Manual March 2003 Rev 3 5/03(English)
© 2003 Fluke Corporation, All rights reserved.
Fluke 707ex Users Manual - Page 5
...
24 V dc
Resolution 1 mV 1 µA
N/A
1 The Fluke 707Ex mA Calibrator (hereafter, "the Calibrator") is ideal for use the Calibrator.
The Calibrator is a compact and easy to 28 V. The Calibrator tests current loops of alligator-clip test leads, a 9 V alkaline battery installed, and this Users manual on a CD. It comes with a set of 0-20 mA or 4-20 mA and measures dc voltage to operate...
Fluke 707ex Users Manual - Page 6
...Calibrator:
• Use the Calibrator only as described in this Users Manual and the Fluke 707Ex mA Calibrator CCD (Concept Control Drawing) or the protection provided by the Calibrator may damage the Calibrator or equipment under test, put the Calibrator...metal. 707Ex Users Manual
Battery Saver
The Calibrator automatically turns off time. With the Calibrator OFF, press D. Replace damaged test...
Fluke 707ex Users Manual - Page 7
...; This equipment is specified for use in an Exhazardous area. mA Calibrator Safety Information
Faults and Damage
Applying a voltage greater than 28 V to the input of the Calibrator in measurement category I (CAT I applications where this manual. Measurement transients are exceeded • Functioning errors or obvious measurement
inaccuracies occur which prevent further measurement by any...
Fluke 707ex Users Manual - Page 8
... information. Certification # LR110460-2. Ex-Certification Data
• ATEX Certificate of Conformity: ZELM 02 ATEX 0120 X • Certification: ( II 2 G EEx ia IIC T4 • Permitted for Division 2 hazardous gases, vapor or mist,
Gas Groups A-D
Symbols
Symbol
Meaning
+ ON / OFF button.
707Ex Users Manual
Safety Regulations
The use of this 707Ex mA Calibrator meets the requirements...
Fluke 707ex Users Manual - Page 9
... start the SpanCheck at a resolution of selected current span, i.e., 0 mA for 0-20 mA span or 4 mA for 100 % of full scale. d is changed. Current output can be adjusted at 0 % of 1 µA or 100 µA. (Default is produced in and turn the knob. mA Calibrator Front Panel Controls
Control
Function
Front Panel Controls Control
D
ON...
Fluke 707ex Users Manual - Page 10
... mA Output Span
The Calibrator has two mA output spans: • 4 mA to 20 mA (0 % to 100 %) [default] • 0 mA to 20 mA (0 % to a passive circuit. 707Ex Users Manual
Using the mA Sourcing (Output) Modes
The Calibrator outputs current for current to flow between the + and
the COM terminals. A path must exist for calibrating and testing 0 to 20 mA and 4 to 20 mA current loops...
Fluke 707ex Users Manual - Page 11
... exit, press any pushbutton or turn the Calibrator off. mA Calibrator Simulating a Transmitter
Auto Ramping the mA Output
Auto ramping allows you . A 12 V to a passive (sourcing) or active (simulate) loop. Insert the test leads as shown below. Simulating a Transmitter
When simulating the operation of a transmitter, the Calibrator regulates the loop current to 0 % stair-step ramp in one...
Fluke 707ex Users Manual - Page 13
... (up to Loop Power mode.
2. Touch the test probes to the unit under test, ensure that the Calibrator is in the correct mode before connecting the test leads. Measuring dc mA with Loop Power
W Caution To prevent damage to the circuit across the load or power source as shown below. mA Calibrator Measuring dc mA with Loop Power:
1.
Fluke 707ex Users Manual - Page 15
... from the Calibrator.
• When servicing the Calibrator, use only specified replacement parts described in the Replaceable Parts section.
• Use only the battery specified in this product. If the Calibrator is necessary, use abrasives or solvents. mA Calibrator Maintenance
In Case of the Calibrator in explosive atmospheres return the Calibrator to Fluke for all repairs.
•...
Fluke 707ex Users Manual - Page 17
...
1
2. Red holster, with bail 2040228
1
5. Test lead set
TL75
1
7. Qty.
1. Users Manual on CD 2053979
1
Approved Batteries
Battery Description
Manufacturer
Type
Alkaline, ...6LR61
6LR61
13 Battery door
665106
1
4. Replaceable Parts
AQV10F.EPS
mA Calibrator Replaceable Parts
Fluke Part Numbers
Item
Part Description
Fluke Part No. Battery, 9 volt, Alkaline 614487 or ...
Fluke 707ex Users Manual - Page 18
not replaceable
General Specifications
Maximum voltage between any terminal and earth ground or between any two terminals:
28 V Storage temperature:
− 30 °C to 60 °C Operating temperature:
− 10 °C to 125 %
Input / Output Protection
Fused; 707Ex Users Manual
Accuracy Specifications
Accuracy is specified for 1 year after calibration at operating temperatures of 18 °...
Fluke 707ex Users Manual - Page 19
... (L) x 2.15 in Replaceable Parts section, page 13)
Battery life (typical): SOURCE mode: 18 hours; 12 mA into 500 Ω; ANSI/ISA S82.02.01-1994; ( Directive 94/9/EG and p NEC 500: Uo = 27.6 V, Io = 96.13 mA, Co = 76 nF, Lo = 2.5 mH, Ui = 30 V, Ii = 24 mA, Ci = 10 nF, Li = 0 mH
mA Calibrator General Specifications
CE: Complies...
Fluke 707ex Users Manual - Page 20
... Fluke distributor or service center, call:
1-888-99-FLUKE (1-888-993-5853) in U.S.A 1-800-36-FLUKE in Canada +31-402-675-200 in Europe +81-3-3434-0181 Japan +65-738-5655 Singapore
+1-425-446-5500 from other countries
Or visit Fluke's web site at : register.fluke.com. 707Ex Users Manual
Contacting Fluke
To contact Fluke for product information, operating assistance, service...
Fluke 707Ex Reviews
We have not received any reviews for Fluke yet.