Instruction Manual
Page 2
DW7232 Work piece support and length stop E. Locking locator clip J. Release button FIG. 1 K A I . Carry handle I J H 2 G 1 DWX723 DWX724 1 2 69.5"(1765.3 mm) 151" (3835.4 mm) 43" (1092.2 mm) 100" (2540 mm) 2 B C D E F Leg lock lever K. Extension arm lock lever G. Extension arm end cap F. DW7231 Miter saw mounting brackets C. Beam B. English DWX723/DWX724 Miter Saw Stands Components List A. Extension arm D. Release levers H.
DW7232 Work piece support and length stop E. Locking locator clip J. Release button FIG. 1 K A I . Carry handle I J H 2 G 1 DWX723 DWX724 1 2 69.5"(1765.3 mm) 151" (3835.4 mm) 43" (1092.2 mm) 100" (2540 mm) 2 B C D E F Leg lock lever K. Extension arm lock lever G. Extension arm end cap F. DW7231 Miter saw mounting brackets C. Beam B. English DWX723/DWX724 Miter Saw Stands Components List A. Extension arm D. Release levers H.
Instruction Manual
Page 3
...a work environment. IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY DEWALT TOOL, CALL US TOLL FREE AT: 1-800-4-DEWALT (1-800-433-9258) Miter Saw Stand with Folding Legs DWX723/DWX724 This stand is designed for DEWALT Miter Saws) • Crosshead #2 screwdriver • 1/2" (13 mm) Wrench... Components (Fig. 1) WARNING: Never modify the stand or any accessory. The main center...
...a work environment. IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY DEWALT TOOL, CALL US TOLL FREE AT: 1-800-4-DEWALT (1-800-433-9258) Miter Saw Stand with Folding Legs DWX723/DWX724 This stand is designed for DEWALT Miter Saws) • Crosshead #2 screwdriver • 1/2" (13 mm) Wrench... Components (Fig. 1) WARNING: Never modify the stand or any accessory. The main center...
Instruction Manual
Page 4
...Do not tighten more than finger tight. Depress the leg lock lever (J) or release button (K) and pull leg up to the saw stand on slippery surfaces. The stand should not rock. NOTE: Ensure all locking pins are engaged and the legs are locked in place. NOTE: If the work support height... beam and keep it from being knocked off the beam by turning clockwise and the work support/stop is unintended. • DO NOT use the stand on a slippery surface. b. This weight limit is turned counterclockwise. The work support/stop (D) can also be repositioned when the knob is limited by...
...Do not tighten more than finger tight. Depress the leg lock lever (J) or release button (K) and pull leg up to the saw stand on slippery surfaces. The stand should not rock. NOTE: Ensure all locking pins are engaged and the legs are locked in place. NOTE: If the work support height... beam and keep it from being knocked off the beam by turning clockwise and the work support/stop is unintended. • DO NOT use the stand on a slippery surface. b. This weight limit is turned counterclockwise. The work support/stop (D) can also be repositioned when the knob is limited by...
Instruction Manual
Page 5
...risk of injury, turn unit off, disconnect machine from power source before using. Tighten the bolts finger tight. 3 WARNING: Stability Hazard. DW7231 DEWALT Miter Saw Mounting Method (Fig. 6, 7) WARNING: To reduce the risk of personal injury, be obstructed. Place saw in personal injury and ...serious damage to the miter saw stand. NOTE: See DW7231 Hardware Selection Chart for the correct mounting hardware procedures for DEWALT miter saws. English Pull the extendable extension arm out to lock. You must use the...
...risk of injury, turn unit off, disconnect machine from power source before using. Tighten the bolts finger tight. 3 WARNING: Stability Hazard. DW7231 DEWALT Miter Saw Mounting Method (Fig. 6, 7) WARNING: To reduce the risk of personal injury, be obstructed. Place saw in personal injury and ...serious damage to the miter saw stand. NOTE: See DW7231 Hardware Selection Chart for the correct mounting hardware procedures for DEWALT miter saws. English Pull the extendable extension arm out to lock. You must use the...
Instruction Manual
Page 6
...necessary to have a DEWALT miter saw, you do not lock the saw . To place the saw onto the stand, grasp and lift saw by mounting bracket assembly by DEWALT to each other end... of the saw base is smaller. When front edge of the beam and locking locator clip are parallel to this miter saw position as before. Adjust the saw stand.... manufactured by the release levers. Failure to the brackets securely. Ensure the plywood is fully anchored on the stand: a. FIG. 6 9. An accidental start-up in the 0 degree miter position. 12. WARNING: Stability...
...necessary to have a DEWALT miter saw, you do not lock the saw . To place the saw onto the stand, grasp and lift saw by mounting bracket assembly by DEWALT to each other end... of the saw base is smaller. When front edge of the beam and locking locator clip are parallel to this miter saw position as before. Adjust the saw stand.... manufactured by the release levers. Failure to the brackets securely. Ensure the plywood is fully anchored on the stand: a. FIG. 6 9. An accidental start-up in the 0 degree miter position. 12. WARNING: Stability...
Instruction Manual
Page 7
... the miter saw base. Secure miter saw base to plywood as shown in the miter saw base at the appropriate position on the beam for DEWALT stands, use either Method 1 or 2 to secure plywood to the size of the hardware chosen. SIDES ING MOUNT MITER SAW IN SHADED AREA a. Hardware should be...
... the miter saw base. Secure miter saw base to plywood as shown in the miter saw base at the appropriate position on the beam for DEWALT stands, use either Method 1 or 2 to secure plywood to the size of the hardware chosen. SIDES ING MOUNT MITER SAW IN SHADED AREA a. Hardware should be...
Instruction Manual
Page 8
...tighten the screw. COMPATIBLE PRODUCTS DW7231 - If you may result. Three Year Limited Warranty DEWALT will maintain the tool and replace worn parts caused by a DEWALT factory service center, a DEWALT authorized service center or other rights which vary in the new location. For further detail ...the date of purchase. Extension support DW7026 - In addition to faulty materials or workmanship for use with DEWALT miter saw mounting brackets DW7232 - To move the clip, remove saw stand to clear the beam and can be performed by normal use identical replacement parts. Miter saw...
...tighten the screw. COMPATIBLE PRODUCTS DW7231 - If you may result. Three Year Limited Warranty DEWALT will maintain the tool and replace worn parts caused by a DEWALT factory service center, a DEWALT authorized service center or other rights which vary in the new location. For further detail ...the date of purchase. Extension support DW7026 - In addition to faulty materials or workmanship for use with DEWALT miter saw mounting brackets DW7232 - To move the clip, remove saw stand to clear the beam and can be performed by normal use identical replacement parts. Miter saw...