Dewalt D28065N Support and Manuals
Get Help and Manuals for this Dewalt item
View All Support Options Below
Free Dewalt D28065N manuals!
Problems with Dewalt D28065N?
Ask a Question
Free Dewalt D28065N manuals!
Problems with Dewalt D28065N?
Ask a Question
Popular Dewalt D28065N Manual Pages
Instruction Manual - Page 3
... or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Please read the instruction manual. IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY DEWALT TOOL, CALL US TOLL FREE AT: 1-800-4-DEWALT (1-800-433-9258). b) Do not operate power tools in the warnings refers to these...
Instruction Manual - Page 4
..., ensure these are caused by a qualified repair person using only identical replacement parts. f) Keep cutting tools sharp and clean....etc. in accordance with the power tool or these instructions, taking into account the working conditions and the work...intended could result in a hazardous situation.
5) SERVICE a) Have your power tool serviced by poorly maintained power tools. b) Do not ...
Instruction Manual - Page 5
... personal protective equipment. Depending on the power tool. English
SAFETY INSTRUCTIONS FOR ALL OPERATIONS
Safety Warnings Common for Grinding, Sanding, Wire Brushing, Polishing or Abrasive, Cutting-Off Operations
a) This power tool is dropped, inspect for loose or cracked wires. Read all instructions listed below may cause loss of balance, vibrate excessively and may result...
Instruction Manual - Page 7
...cut -off wheel. Investigate and take corrective action to shatter. The wheel may occur. Supports must be used only for any oversized workpiece to a complete stop. Loose and spinning ... entangle your selected wheel. e) Do not use excessively oversized sanding disc paper. e) Support panels or any reason, switch off wheel or apply excessive pressure.
Larger sanding paper extending...
Instruction Manual - Page 8
...use side handle. Minimum Gauge for Cord Sets
Ampere Rating
Volts
Total Length of power...12
Not Recommended
6 Additional Safety Rules for Grinders
WARNING: The grinding wheel or accessory may loosen... or another practical way to secure and support the workpiece to use Type 11 (flaring...parts and should always be avoided. Wire wheel or brush may result.
• Do not operate this manual...
Instruction Manual - Page 10
... modify the power tool or any part of flammable liquids or gases. Lock On Button
(D28065, D28115 only) C. Yellow Rubber Ring
G1. ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of injury, turn unit off . A. Type 27 Guard E. Quick-Change Backing Flange
G2. These heavy-duty angle grinders are professional power tools. Before reconnecting...
Instruction Manual - Page 13
... to attach the gear case to use with grinder accessories. Re-install guard and correct flanges for information on pages 9-11 of this manual. Mounting instructions for these accessory guards are provided with a guard intended for a circular saw and should not be above listed minimum wheel speed as shown on the tool warning label. Accessories...
Instruction Manual - Page 14
...installing and removing accessories, before turning the tool off while under load conditions. With the guard latch open the guard latch, rotate the guard so
that the tool is important to choose the correct guards and flanges to repair
or replace... body should not be above listed minimum wheel speed as shown on
the gear case hub.
3. Allow the grinder to stop before laying the ...
Instruction Manual - Page 15
... stop . Operate the spindle lock only when the tool is retained to the grinder by pushing and twisting the flange
before placing wheel.
13 Refer to the tool...switch as the activation of a ground fault interrupter, throwing of the wheel.
4. Install the stamped steel quick-change backing flange (G2) (D28065, D28065N
N
only) for Type 27 6" (152 mm) wheels or
the quick-change FIG...
Instruction Manual - Page 16
...more than 1/2" (12.7 mm) in depth]. Type 1 guards are installing is
established in the work surface.
2. Once a cut is begun and a notch is more information. Edge grinding wheels...tool from you are not
designed to do not
change the angle of the guard must be positioned away from your local dealer or authorized service
center. 1. Apply minimum pressure to the work
surface, ...
Instruction Manual - Page 17
...PADS (FIG. 13)
Choose the proper grit sandpaper for grinding wheel, sanding flap disc, wire brush or wire wheel applications after sanding applications are complete.
1. Allow the tool to reach full speed...injury may result.
Maintain a 5˚ to 15˚ angle between the tool and work surface, allowing the tool to 10˚ angle between the tool and work surface.
15 The sanding disc ...
Instruction Manual - Page 18
...surface, allowing the tool to stop
rotating before laying it down .
CAUTION: Wheel or brush must not touch guard when mounted or while in a circular motion causes
5˚-15&#... Allow the tool to 10˚ angle between the edge of grinder may result in
the work surface.
2.
English
4. Maintain a 5˚ to stop rotating before setting it down . CAUTION: Failure to ...
Instruction Manual - Page 20
...a DEWALT authorized service center or other harsh chemicals for :
• WARRANTY SERVICE: Registering your product will cause the wheel to work surface, allowing tool to ensure that the tool is a problem with clean, dry air at high speed. dewalt.com.
Repairs
To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment (including brush inspection and replacement) should...
Instruction Manual - Page 21
...DEWALT will maintain the tool and replace worn parts caused by normal use, for a free replacement.
19
DXXXXX
English
In addition to the warranty, DEWALT tools are covered by others. no questions asked. FREE WARNING LABEL REPLACEMENT: If your DEWALT Power Tool, Laser, or Nailer for any defects due to accessories or damage caused where repairs...FREE SERVICE DEWALT will repair, without...
Instruction Manual - Page 72
N234380 D28065, D28065N, D28115, D28115N Copyright © 2007, 2012 DEWALT
The following are trademarks for one or more DEWALT power tools: the yellow and black color scheme, the "D" shaped air intake grill, the array of pyramids on the handgrip, the kit box configuration, and ...
Dewalt D28065N Reviews
We have not received any reviews for Dewalt yet.