Dewalt DWS716XPS Support and Manuals
Get Help and Manuals for this Dewalt item
View All Support Options Below
Free Dewalt DWS716XPS manuals!
Problems with Dewalt DWS716XPS?
Ask a Question
Free Dewalt DWS716XPS manuals!
Problems with Dewalt DWS716XPS?
Ask a Question
Popular Dewalt DWS716XPS Manual Pages
Instruction Manual - Page 3
...override levers 21 Vertical material clamp 22 Miter detent override 23 CUTLINE LED On/Off switch
(DWS716XPS only)
WARNING! Failure to follow the warnings and instructions may result in minor or moderate injury...This instruction manual uses the following safety alert symbols and words to alert you have any questions or comments about this or any DeWALT tool, call us toll free at: 1-800-4-DeWALT ...
Instruction Manual - Page 4
... the spinning blade.
Stacked multiple workpieces cannot be repaired.
If the cut to rain or wet conditions. If confined, i.e. using only identical replacement parts. Rods have a tendency to roll while being thrown. Wait for Miter Saws
a ) Miter saws are intended to a rotating part of cutting either hand closer than the miter saw may not be obvious and you to be...
Instruction Manual - Page 5
... over, causing serious injury.
• USE ONLY CROSSCUT SAW BLADES recommended for miter saws. Small chip accumulation under the saw may interfere with the saw ) to replace safety rules. To reduce your saw blade or may cause personal injury.
• SECURE THE MACHINE TO A STABLE SUPPORTING SURFACE. Additional Safety Rules for Miter Saws
WARNING: Do not allow familiarity (gained from...
Instruction Manual - Page 6
... instruction manual, the carton should remain accurate. Width 7.9" (200.7 mm)
Resulting Height 1.1" (28 mm)
Max. A)
WARNING: Never modify the power tool or any adjustments.
4
To transport the saw, lower the arm of it to rise to its various parts. Once made, these directions carefully to the guard for a complete list of cut
50° miter...
Instruction Manual - Page 7
... due to the saw and severe personal injury. C
English
WARNING: • The guard bracket must be raised far
enough to Table (Fig.
D
24
6. NOTE: For blades with a blade hole of the blade teeth with the square. E 26 25
7 5
6
Miter Pointer Adjustment (Fig.
Assemble the outer blade clamp onto the spindle. 4. Install the blade...
Instruction Manual - Page 8
...DeWALT service...8226; To set the 33...MANUALLY UNLESS THE SAW...serviced by giving the saw is pulled down and to provide clearance. To reduce the risk of trigger release. NOTE: Certain special cuts of the fences can be sure the blade has stopped before removing it in place and move up and down . English Fig. Make a dry run with sawdust. NOTE: The guide...installing or removing saw...
Instruction Manual - Page 9
.... Keep both feet firmly on the wood. The stop knob. The saw blade close to pivot past the 45° mark. The accuracy setting will remove when performing a cut . A)
WARNING: The lock down on .
English
Miter Lock Adjustment (Fig. A) DWS716XPS ONLY NOTE: The miter saw head safely down and pull the pin out. The light does...
Instruction Manual - Page 10
... Install Clamp (Fig. Make the cut . In order to set the bevel adjustment to zero and the miter arm to Saw Blades under Optional Accessories. Ensure that best fits your saw ...SUPPORT LONG PIECES. Q)
To best understand how to aid in place. For this saw 's dust collection efficiency. The two sketches in Figure P. Remove dust bag 37 from your local retailer or DeWALT service...
Instruction Manual - Page 11
... angle and straight across to the nearest 1/4°. R
Fig. To set miter angles to find the correct miter angle. Turn off miter saw , allow the blade to align the appropriate vernier mark with the CLOSEST degree mark on the saw . 2. To decrease the miter angle when mitering to the right, move the arm to the
RIGHT until you...
Instruction Manual - Page 12
... molding. (The numbers for purchase from adhering to set on the table at 33.9° left side of 52° and a bottom rear angle (the part that you will be tested on your local DeWALT retailer or DeWALT service center. W) Place the molding on your saws bevel and miter scales per the chart below .
Never apply stick...
Instruction Manual - Page 13
.... Z
Fig. This is extremely important when making any part of wood a little too large to Saw Blades under Accessories for miter saws. Cutting Large Material (Fig. Release the guard prior to the nearest service center for precision cutting.
They are provided to allow debris to attack by DeWALT, have not been tested with this purpose.
11...
Instruction Manual - Page 14
... or Installing a New Saw Blade.
English
Repairs
WARNING: To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment (including brush inspection and replacement, when applicable) should be performed by others. This warranty does not apply to speed Machine vibrates excessively Does not make accurate miter cuts
Material pinches blade 12
Troubleshooting Guide
BE SURE...
Instruction Manual - Page 15
English
SET THIS MITER ANGLE ON SAW ANGLE OF SIDE OF BOX (ANGLE A)
TABLE 1: COMPOUND MITER CUT (POSITION WOOD WITH BROAD FLAT SIDE ON THE TABLE AND THE NARROW EDGE AGAINST THE FENCE)
10 20
30
40
10 20
10 20 30
30
40
6-SIDED
50
BOX
40
8-SIDED
50
BOX
60
60 70 80
70 80
50
SQUARE BOX
60
70
80
SET THIS BEVEL ANGLE ON SAW
13
Instruction Manual - Page 44
... Co., 701 East Joppa Road, Towson, MD 21286 (AUG19) Part No. N748087 DWS716, DWS716XPS Copyright © 2018, 2019 DeWALT
The following are trademarks for one or more DeWALT power tools: the yellow and black color scheme, the "D" shaped air intake grill, the array of pyramids on the handgrip, the kit box configuration, and ...
Dewalt DWS716XPS Reviews
We have not received any reviews for Dewalt yet.