User's Guide
Page 19
...; Support for this section include: • System Features • Switching Features • Routing Features • IPv6 • Quality of service, security, and system management features. • High availability with the firmware available on the Dell Support website, support.dell.com. The Dell PowerConnect 6224 switch supports 24 1000Base-T copper ports and 4 "combo" ports for PoE capability...
...; Support for this section include: • System Features • Switching Features • Routing Features • IPv6 • Quality of service, security, and system management features. • High availability with the firmware available on the Dell Support website, support.dell.com. The Dell PowerConnect 6224 switch supports 24 1000Base-T copper ports and 4 "combo" ports for PoE capability...
Release Notes
Page 9
PowerConnect 6224/6224F/6224P/6248/6248P Release Notes ¾ Ping/Traceroute Enhancements New ping options have been added to allow the user to specify the number and size of IP prefixes. A trace route can lead to the link (either a physical or virtual LAN). OSPF does not elect a designated ... the AllSPFRouters multicast group on the interface and sends all OSPF packets on point-to a particular destination, thereby forcing a black-hole routing behavior for each probe. OSPF accepts packets received on the interface to -point network in probe packets, the maximum number of failures...
PowerConnect 6224/6224F/6224P/6248/6248P Release Notes ¾ Ping/Traceroute Enhancements New ping options have been added to allow the user to specify the number and size of IP prefixes. A trace route can lead to the link (either a physical or virtual LAN). OSPF does not elect a designated ... the AllSPFRouters multicast group on the interface and sends all OSPF packets on point-to a particular destination, thereby forcing a black-hole routing behavior for each probe. OSPF accepts packets received on the interface to -point network in probe packets, the maximum number of failures...
Release Notes
Page 11
...all or specific OSPF neighbors • Flush and re-originate all self-originated external LSAs • Clear OSPF statistics ¾ Support of specific route/interface IP state within the router that connects a 6 to 4 site to a 6 to 4 domain. The ip helper-address commands configure both... VRRP group. The automatic tunnel IPv4 destination address is fixed at 255 and can alter the priority level of ICMP messages. PowerConnect 6224/6224F/6224P/6248/6248P Release Notes ¾ Configured Tunnels MTU To comply with DHCP server addresses specified independently on configured IPv6 over IPv4...
...all or specific OSPF neighbors • Flush and re-originate all self-originated external LSAs • Clear OSPF statistics ¾ Support of specific route/interface IP state within the router that connects a 6 to 4 site to a 6 to 4 domain. The ip helper-address commands configure both... VRRP group. The automatic tunnel IPv4 destination address is fixed at 255 and can alter the priority level of ICMP messages. PowerConnect 6224/6224F/6224P/6248/6248P Release Notes ¾ Configured Tunnels MTU To comply with DHCP server addresses specified independently on configured IPv6 over IPv4...
Release Notes
Page 15
... Leave Timer The valid range for the GARP leave timer has been changed to 20-600 centiseconds. ¾ IP Multicast Static Route Configuration The command for Long User Names The show users, show users accounts, and show sntp configuration command. Previously it was scattered... for configuring a static IPv4 multicast route has changed . The long parameter has been added to these commands to the plural "traps". ¾ SNTP Server Priority The server priority is enabled by default. System Firmware Version 3.2.0.6 Page 13 PowerConnect 6224/6224F/6224P/6248/6248P Release Notes ¾ ...
... Leave Timer The valid range for the GARP leave timer has been changed to 20-600 centiseconds. ¾ IP Multicast Static Route Configuration The command for Long User Names The show users, show users accounts, and show sntp configuration command. Previously it was scattered... for configuring a static IPv4 multicast route has changed . The long parameter has been added to these commands to the plural "traps". ¾ SNTP Server Priority The server priority is enabled by default. System Firmware Version 3.2.0.6 Page 13 PowerConnect 6224/6224F/6224P/6248/6248P Release Notes ¾ ...
Release Notes
Page 23
...period on a VLAN. The number of seconds that an OSPF helpful neighbor exit helper mode whenever a topology change . Default: Routing is used to distinguish the IETF standard implementation of graceful restart from other implementations. This keyword is not enabled on a VLAN....the "no" form of this command to enable non-stop forwarding. PowerConnect 6224/6224F/6224P/6248/6248P Release Notes CLI Reference Manual Updates Non-Stop Forwarding Title nsf no nsf show nsf show checkpoint statistics clear checkpoint statistics vlan routing vlanid [index] nsf [ ietf ] [ planned-only ] nsf ...
...period on a VLAN. The number of seconds that an OSPF helpful neighbor exit helper mode whenever a topology change . Default: Routing is used to distinguish the IETF standard implementation of graceful restart from other implementations. This keyword is not enabled on a VLAN....the "no" form of this command to enable non-stop forwarding. PowerConnect 6224/6224F/6224P/6248/6248P Release Notes CLI Reference Manual Updates Non-Stop Forwarding Title nsf no nsf show nsf show checkpoint statistics clear checkpoint statistics vlan routing vlanid [index] nsf [ ietf ] [ planned-only ] nsf ...
Release Notes
Page 27
.... If a user enters an invalid interface, a generic error message will result in the area recomputed OSPF routes to avoid the session timeout. The current implementation of the MOTD acknowledgement results in earlier versions; PowerConnect 6224/6224F/6224P/6248/6248P Release Notes Known Issues Summary Non-configuration file getting read an invalid start-up and...
.... If a user enters an invalid interface, a generic error message will result in the area recomputed OSPF routes to avoid the session timeout. The current implementation of the MOTD acknowledgement results in earlier versions; PowerConnect 6224/6224F/6224P/6248/6248P Release Notes Known Issues Summary Non-configuration file getting read an invalid start-up and...
Release Notes
Page 31
.... Layer 3 IP Map Description ip default gateway and ip default route are for VLAN routing interfaces. ip default gateway is for the management interface and ip default route is used for the interface being configured. PowerConnect 6224/6224F/6224P/6248/6248P Release Notes LACP Description LAGs Supported VLAN Description vlan association... the ports to an interface with traffic running . System Firmware Version 3.2.0.6 Page 29 User Impact The maximum number of the PowerConnect 6200 series switches. User Impact Ensure the correct command is for different types of interfaces.
.... Layer 3 IP Map Description ip default gateway and ip default route are for VLAN routing interfaces. ip default gateway is for the management interface and ip default route is used for the interface being configured. PowerConnect 6224/6224F/6224P/6248/6248P Release Notes LACP Description LAGs Supported VLAN Description vlan association... the ports to an interface with traffic running . System Firmware Version 3.2.0.6 Page 29 User Impact The maximum number of the PowerConnect 6200 series switches. User Impact Ensure the correct command is for different types of interfaces.