Operation Manual
Page 1
Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A. SAFETY ASSEMBLY OPERATION MAINTENANCE Operator's Manual Oscillating Spindle SANDER Model No. 351.215000 CAUTION: Read and follow all Safety Rules and Operating Instructions before First Use of this manual with tool. www.sears.com/craftsman 25759.00 Draft (01/22/08) PARTS LIST ESPAÑOL Keep this Product.
Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A. SAFETY ASSEMBLY OPERATION MAINTENANCE Operator's Manual Oscillating Spindle SANDER Model No. 351.215000 CAUTION: Read and follow all Safety Rules and Operating Instructions before First Use of this manual with tool. www.sears.com/craftsman 25759.00 Draft (01/22/08) PARTS LIST ESPAÑOL Keep this Product.
Operation Manual
Page 2
... Warranty 2 Safety Rules 2-3 Unpacking 3 Assembly 3-4 Installation 4-5 Operation 5-6 Maintenance 6 Troubleshooting 7 Parts Illustration and List 8-9 Español 12-19 WARRANTY ONE-YEAR FULL WARRANTY ON CRAFTSMAN TOOL If this Craftsman tool fails due to a defect in moving parts of machine. • Wear protective hair covering to contain long hair. • Wear safety shoes with non...
... Warranty 2 Safety Rules 2-3 Unpacking 3 Assembly 3-4 Installation 4-5 Operation 5-6 Maintenance 6 Troubleshooting 7 Parts Illustration and List 8-9 Español 12-19 WARRANTY ONE-YEAR FULL WARRANTY ON CRAFTSMAN TOOL If this Craftsman tool fails due to a defect in moving parts of machine. • Wear protective hair covering to contain long hair. • Wear safety shoes with non...
Operation Manual
Page 3
... Secure sleeve in a place with knob. Check for completeness. A Table Inserts (6 1″, 1½″, 2″ and 3″) B Spindle Knob C Drum Washers (5), (¾″, 1″, 1½″, 2″ and 3″) D Spindle Drums (5), (¾″, 1″, 1½″, 2″ and 3″) E Abrasive Sleeves (6 1″, 1½″, 2″... will not spin loose on drum and secure drum in line with the wood while using the tool. • Sander can be filled with knob. Attaching the ½″ Sleeve Direction Arrow on sleeve securely so...
... Secure sleeve in a place with knob. Check for completeness. A Table Inserts (6 1″, 1½″, 2″ and 3″) B Spindle Knob C Drum Washers (5), (¾″, 1″, 1½″, 2″ and 3″) D Spindle Drums (5), (¾″, 1″, 1½″, 2″ and 3″) E Abrasive Sleeves (6 1″, 1½″, 2″... will not spin loose on drum and secure drum in line with the wood while using the tool. • Sander can be filled with knob. Attaching the ½″ Sleeve Direction Arrow on sleeve securely so...
Operation Manual
Page 4
POWER SOURCE WARNING: Do not connect sander to a two pole outlet if it will be performed by an authorized service facility. • Green (or green and yellow) conductor in outlet, have proper outlet installed by a qualified electrician. • Inspect tool cords periodically, and if damaged, have ... the electric cord or plug is necessary, do not connect the green (or green and yellow) wire to whether the tool is properly grounded. • This tool is encountered, it must be replaced with a properly grounded 3-prong receptacle installed in any manner. The motor is provided...
POWER SOURCE WARNING: Do not connect sander to a two pole outlet if it will be performed by an authorized service facility. • Green (or green and yellow) conductor in outlet, have proper outlet installed by a qualified electrician. • Inspect tool cords periodically, and if damaged, have ... the electric cord or plug is necessary, do not connect the green (or green and yellow) wire to whether the tool is properly grounded. • This tool is encountered, it must be replaced with a properly grounded 3-prong receptacle installed in any manner. The motor is provided...
Operation Manual
Page 5
... position. 5 To turn the sander ON, pull the switch to the up to full speed before commencing power tool operation. Wiring Schematic Motor The power lines are available at 120 volts. DESCRIPTION The Craftsman Oscillating Spindle Sander makes sanding irregular shapes and curves...convenient. OPERATION Refer to fit Sears wet/dry vacuums. SPECIFICATIONS Spindle diameter Drum diameters 1″, 1½″, 2″ and 3″ Drum length 4½″ Spindle stroke 1″ Spindle oscillation 30 SPM Spindle speed 1725 RPM Table diameter 18″ Table height 14...
... position. 5 To turn the sander ON, pull the switch to the up to full speed before commencing power tool operation. Wiring Schematic Motor The power lines are available at 120 volts. DESCRIPTION The Craftsman Oscillating Spindle Sander makes sanding irregular shapes and curves...convenient. OPERATION Refer to fit Sears wet/dry vacuums. SPECIFICATIONS Spindle diameter Drum diameters 1″, 1½″, 2″ and 3″ Drum length 4½″ Spindle stroke 1″ Spindle oscillation 30 SPM Spindle speed 1725 RPM Table diameter 18″ Table height 14...
Operation Manual
Page 6
.... DUST COLLECTION Refer to the tool. it easier to service or remove any damaged or missing parts. Sawdust buildup beneath the table may prevent the spindle from oscillating completely, causing damage to Figure ... down between the table insert and sanding sleeve. Use parts list to OFF position and disconnect sander from power source. • Pull the key out. Medium grit may create a hazard unless... of dust. No. 54). Choose the size that the unit is frequently vacuumed free of Craftsman wet/dry vacuums. The use the correct size table insert with each grit until it replaced ...
.... DUST COLLECTION Refer to the tool. it easier to service or remove any damaged or missing parts. Sawdust buildup beneath the table may prevent the spindle from oscillating completely, causing damage to Figure ... down between the table insert and sanding sleeve. Use parts list to OFF position and disconnect sander from power source. • Pull the key out. Medium grit may create a hazard unless... of dust. No. 54). Choose the size that the unit is frequently vacuumed free of Craftsman wet/dry vacuums. The use the correct size table insert with each grit until it replaced ...