Cisco WS-X4232 - Catalyst 4232 - Switch Support and Manuals
Get Help and Manuals for this Cisco item
View All Support Options Below
Free Cisco WS-X4232 manuals!
Problems with Cisco WS-X4232?
Ask a Question
Free Cisco WS-X4232 manuals!
Problems with Cisco WS-X4232?
Ask a Question
Popular Cisco WS-X4232 Manual Pages
Hardware Maintenance Manual - Page 3
... WHOLE OR IN PART, SOFTWARE OR DOCUMENTATION; Customer agrees to implement reasonable security measures to Software and documentation shall remain solely with Cisco.
Printed in this manual is error free or that Cisco or its Sales or Service Partner in creating the environment in the event that aspects of the licensed materials, including the specific design and...
Hardware Maintenance Manual - Page 4
... applicable export laws and regulations if it acquired the Hardware or the Cisco Service Partner if the Hardware was exported under the multinational uplift program.
Cisco warrants to either (i) provide advance replacement service as set forth in such a way that Cisco cannot reasonably reproduce the Software error, or (6) has been exported from the original country of this License...
Hardware Maintenance Manual - Page 5
TABLE OF CONTENTS
About This Manual xv Document Objectives xv Audience xv Document Organization xv Document Conventions xvi
Chapter 1 Cisco 4000 Series Overview 1-1 External Differences in Models of the Cisco 4000 Series 1-1 Series Specifications 1-2 Memory Systems 1-4
Chapter 2 Preparing for Installation 2-1 Safety Recommendations 2-2 Safety with Electricity 2-2 Preventing Electrostatic Discharge...
Hardware Maintenance Manual - Page 14
... Cable Pinouts (P/N 72-0799-xx) A-23 E1 Interface Cable Pinouts A-24 Virtual Configuration Bit Meanings B-1 Explanation of Boot Field (Configuration Register Bits 00-03) B-3 Default Boot Filenames B-4 Configuration Register Settings for Broadcast Address Destination B-5 System Console Terminal Baud Rate Settings B-5 O Command Options C-3
xiv Cisco 4000 Series Hardware Installation and Maintenance
Hardware Maintenance Manual - Page 15
...have experience as an annual subscription.
To order UniverCD, contact your warranty package. About This Manual xv
Document Objectives
This publication contains the initial site preparation, installation, troubleshooting, and selected upgrade and maintenance procedures. Note To order UniverCD, Cisco's online library of this publication to the appropriate software publication. About This...
Hardware Maintenance Manual - Page 16
... Initial Hardware Configuration," includes a troubleshooting
overview, problem-solving instructions, environmental reporting features, and understanding front-panel and network-processor module LED indicators.
• Chapter 5, "Maintaining and Upgrading the Router," includes instructions for opening the
chassis, replacing or adding network processor modules, and replacing single in-line memory...
Hardware Maintenance Manual - Page 37
...
Balanced drivers allow ...support asynchronous connections.
generally, the slower the baud rate, the greater the distance. For instance, the recommended maximum rate for V.35 is 2 Mbps, but 4 Mbps is completely lost. Preparing for each serial interface type; Network Connection Considerations
Serial Connections
When setting...support 4-Mbps rates. If you understand the electrical problems...
Hardware Maintenance Manual - Page 43
...Installation 2-21
Figure 2-22 Dual Serial Network Processor Module Jumpers, J4 and J5-NRZI Setting
J5 J4
Pin 1
H1125a
Port 1
Port 0
You must also be manually...set, or if the cable is DCE and the clock rate is not configured. See the appendix "Cabling Specifications... 2-21. This cable, available from your customer service representative, is normally ordered with the clockrate command....
Hardware Maintenance Manual - Page 44
...to the port.
When a port is operating in place of error packets, suspect a phase shift. Configuration commands are not supported for EIA/TIA-232. This section describes how to set the clock speed with the clockrate configuration command. If a DCE... the internal clock signal:
interface serial 0 dce-terminal-timing-enable
2-22 Cisco 4000 Series Hardware Installation and Maintenance
Hardware Maintenance Manual - Page 54
On the CE1, the controller provides up to 120-ohm.
2-32 Cisco 4000 Series Hardware Installation and Maintenance Each virtual channel is presented to the system as described in the G.703 specification. This interface is set with one E1 interface.The CE1 provides one channelized E1 connection via a serial cable to 120-ohm or 75...
Hardware Maintenance Manual - Page 55
Warning To prevent problems with no ground. By default and for safety, J2 has been configured with the E1 interface and to reduce the potential for Installation 2-33
This is a setting that could pose a risk of severe injury. For either BNC, DB-15, Twinax, or RJ-45 connectors on the CE1 Module
J2 J3
J4...
Hardware Maintenance Manual - Page 64
... NT1 is customer owned.
3-6 Cisco 4000 Series Hardware Installation and Maintenance The common carrier will provide the NT1 connection worldwide, except in North America, where the NT1 is customer owned. kHz = kilohertz. 2. Each BRI port is an ISDN channel service unit/digital service unit (CSU/DSU). The NT1 is an RJ-45 8-pin connector. Warning...
Hardware Maintenance Manual - Page 123
...manually boot the system each time you reboot the router. While running the system software, you can break to 0x0 by setting the configuration register. During the 60-second window, you isolate or rule out hardware problems encountered when installing your router. Entering the Cisco... enabled for an explanation of the o/r command. Cisco 4000-M ROM Monitor C-1 The ROM monitor can ...
Hardware Maintenance Manual - Page 127
...monitor. APPENDIX D
Cisco 4500-M and Cisco 4700 ROM Monitor
This appendix describes the Cisco 4500-M and Cisco 4700 ROM monitor, the first software to run when the router is provided.
If you set the configuration to ... reset. The ROM Monitor can break to manually boot the system from the console each time you isolate or rule out hardware problems encountered when installing your router.
Hardware Maintenance Manual - Page 141
... 4-8 power LED indication 3-22 light 4-3 specifications 1-3 supply features 2-4 system, troubleshooting 4-2 preparing for installation 2-1 to make connections 2-7 preventing ESD damage 2-3 preventive site configuration 2-4 printing summary of ROM monitor commands problem indications 4-3 temperature 4-3 problem solving 4-1 processor specifications 1-3 protocol analyzer, attaching 2-9 publications...
Cisco WS-X4232 Reviews
We have not received any reviews for Cisco yet.