Hardware Installation Guide
Page 58
... guard, contact your Cisco representative and use these...8TC-L, 2960-8TC-S, and 2960PD-8TT-L switches cable guard part number: CBLGRD-C2960-8TC= • Catalyst 2960G-8TC-L switch cable guard part number: CBLGRD-C2960G.... - Preparing for Installation Chapter 3 Switch Installation (8-Port Switches) • Do not stack switches or place switches side-by at least 3 inches (7.6 cm) of clearance from each...lists the cable specifications for 1000BASE-X and 100BASE-X small form-factor (SFP) modules available for the Catalyst 2960 switch. Catalyst 2960 Switch Hardware Installation Guide 3-4 OL...
... guard, contact your Cisco representative and use these...8TC-L, 2960-8TC-S, and 2960PD-8TT-L switches cable guard part number: CBLGRD-C2960-8TC= • Catalyst 2960G-8TC-L switch cable guard part number: CBLGRD-C2960G.... - Preparing for Installation Chapter 3 Switch Installation (8-Port Switches) • Do not stack switches or place switches side-by at least 3 inches (7.6 cm) of clearance from each...lists the cable specifications for 1000BASE-X and 100BASE-X small form-factor (SFP) modules available for the Catalyst 2960 switch. Catalyst 2960 Switch Hardware Installation Guide 3-4 OL...
Hardware Installation Guide
Page 60
...-Based Setup Program." See the switch getting started guide for instructions. 3. Note We strongly recommend that you attach the rubber feet. Do not stack switches or place switches side-by-side unless they are separated on top of clearance around the ventilation openings to the other . For configuration instructions...on the desk or shelf. See the "Connecting to the 10/100 and 10/100/1000 Ports" section on page 2-14, the "Connecting to SFP Modules" section on page 2-18, and the "Connecting to a Dual-Purpose Port" section on the bottom of the switch. and 48-Port Switches)." This ...
...-Based Setup Program." See the switch getting started guide for instructions. 3. Note We strongly recommend that you attach the rubber feet. Do not stack switches or place switches side-by-side unless they are separated on top of clearance around the ventilation openings to the other . For configuration instructions...on the desk or shelf. See the "Connecting to the 10/100 and 10/100/1000 Ports" section on page 2-14, the "Connecting to SFP Modules" section on page 2-18, and the "Connecting to a Dual-Purpose Port" section on the bottom of the switch. and 48-Port Switches)." This ...
Hardware Installation Guide
Page 107
...modules 1000BASE-T supported speeds 1-17 bale-clasp latch removal 2-17 cables B-4 connecting to 2-18 to 2-20 connectors B-3 described 1-13 installation 2-16 to 2-17 shelf-mounting 2-14, 3-6 Simple Network Management Protocol See SNMP SNMP network management platforms 1-22 software switch management 1-22 specifications A-1 speed, troubleshooting 4-4 stacking...4-4 switch performance 4-4 troubleshooting spanning tree loops 4-4 W wall-mounting 2-11, 3-16 warnings attaching the Cisco RPS 2-2, 2-6 circuit protection 2-3 class 1 laser product 2-3, 3-2 disconnecting device 2-3 Ethernet cables 2-2, 3-2...
...modules 1000BASE-T supported speeds 1-17 bale-clasp latch removal 2-17 cables B-4 connecting to 2-18 to 2-20 connectors B-3 described 1-13 installation 2-16 to 2-17 shelf-mounting 2-14, 3-6 Simple Network Management Protocol See SNMP SNMP network management platforms 1-22 software switch management 1-22 specifications A-1 speed, troubleshooting 4-4 stacking...4-4 switch performance 4-4 troubleshooting spanning tree loops 4-4 W wall-mounting 2-11, 3-16 warnings attaching the Cisco RPS 2-2, 2-6 circuit protection 2-3 class 1 laser product 2-3, 3-2 disconnecting device 2-3 Ethernet cables 2-2, 3-2...