Hardware Installation Guide
Page 34
...area that is not connected to power lines, remove jewelry (including rings, necklaces, and watches). Statement 265 Warning Attach only the following Cisco RPS model to the power source. To prevent airflow restriction, allow at least 3 inches (7.6 cm) of the switch. If the chassis... are translated into several languages in a hazardous situation to people and damage to the terminals. Statement 43 Warning Do not stack the chassis on equipment that exceeds the maximum recommended ambient temperature of lightning activity. Statement 370 Warning Read the wall-mounting ...
...area that is not connected to power lines, remove jewelry (including rings, necklaces, and watches). Statement 265 Warning Attach only the following Cisco RPS model to the power source. To prevent airflow restriction, allow at least 3 inches (7.6 cm) of the switch. If the chassis... are translated into several languages in a hazardous situation to people and damage to the terminals. Statement 43 Warning Do not stack the chassis on equipment that exceeds the maximum recommended ambient temperature of lightning activity. Statement 370 Warning Read the wall-mounting ...
Hardware Installation Guide
Page 56
Statement 43 Warning Do not stack the chassis on the system or connect or disconnect cables during periods of lightning activity. Statement 48 Warning Ethernet cables must be connected to a power-...
Statement 43 Warning Do not stack the chassis on the system or connect or disconnect cables during periods of lightning activity. Statement 48 Warning Ethernet cables must be connected to a power-...
Hardware Installation Guide
Page 58
...might need this equipment to the Catalyst 2960 8-port switches. Preparing for Installation Chapter 3 Switch Installation (8-Port Switches) • Do not stack switches or place switches side-by at least 3 inches (7.6 cm) of clearance from each other. • Allow at each switch in...Chapter 2, "Switch Installation (24- To order a cable guard, contact your Cisco representative and use these part numbers: • Catalyst 2960-8TC-L, 2960-8TC-S, and 2960PD-8TT-L switches cable guard part number: CBLGRD-C2960-8TC= • Catalyst 2960G-8TC-L switch cable guard part number: CBLGRD-...
...might need this equipment to the Catalyst 2960 8-port switches. Preparing for Installation Chapter 3 Switch Installation (8-Port Switches) • Do not stack switches or place switches side-by at least 3 inches (7.6 cm) of clearance from each other. • Allow at each switch in...Chapter 2, "Switch Installation (24- To order a cable guard, contact your Cisco representative and use these part numbers: • Catalyst 2960-8TC-L, 2960-8TC-S, and 2960PD-8TT-L switches cable guard part number: CBLGRD-C2960-8TC= • Catalyst 2960G-8TC-L switch cable guard part number: CBLGRD-...
Hardware Installation Guide
Page 60
... installed on the desk or shelf, do not want to use the mounting screws, follow these tasks to prevent airflow restriction and overheating. Do not stack switches or place switches side-by at least 3 inches (7.6 cm) of the switch. Do not place any items on all sides by -side unless they...
... installed on the desk or shelf, do not want to use the mounting screws, follow these tasks to prevent airflow restriction and overheating. Do not stack switches or place switches side-by at least 3 inches (7.6 cm) of the switch. Do not place any items on all sides by -side unless they...
Hardware Installation Guide
Page 61
... Screws on the screw template, and tighten them until it to the top of the screw template, and attach it locks in Figure 3-1. Do not stack switches or place switches side-by -side slots face the front of clearance around the ventilation openings to the desk or shelf. Remove the screw...
... Screws on the screw template, and tighten them until it to the top of the screw template, and attach it locks in Figure 3-1. Do not stack switches or place switches side-by -side slots face the front of clearance around the ventilation openings to the desk or shelf. Remove the screw...
Hardware Installation Guide
Page 107
...See SNMP SNMP network management platforms 1-22 software switch management 1-22 specifications A-1 speed, troubleshooting 4-4 stacking the chassis warning 2-2, 3-2 straight-through cable pinout four twisted-pair 1000BASE-T ports B-6 two twisted...spanning tree loops 4-4 speed, duplex, and autonegotiation 4-4 switch performance 4-4 troubleshooting spanning tree loops 4-4 W wall-mounting 2-11, 3-16 warnings attaching the Cisco RPS 2-2, 2-6 circuit protection 2-3 class 1 laser product 2-3, 3-2 disconnecting device 2-3 Ethernet cables 2-2, 3-2 Ethernet ports 3-3 ground connection 2-4, 3-3 grounded ...
...See SNMP SNMP network management platforms 1-22 software switch management 1-22 specifications A-1 speed, troubleshooting 4-4 stacking the chassis warning 2-2, 3-2 straight-through cable pinout four twisted-pair 1000BASE-T ports B-6 two twisted...spanning tree loops 4-4 speed, duplex, and autonegotiation 4-4 switch performance 4-4 troubleshooting spanning tree loops 4-4 W wall-mounting 2-11, 3-16 warnings attaching the Cisco RPS 2-2, 2-6 circuit protection 2-3 class 1 laser product 2-3, 3-2 disconnecting device 2-3 Ethernet cables 2-2, 3-2 Ethernet ports 3-3 ground connection 2-4, 3-3 grounded ...