Hardware Installation Guide
Page 34
Statement 43 Warning Do not stack the chassis on the back of 113•F (45•C). Statement 1001 Warning Read the installation instructions before beginning installation. To prevent airflow restriction, allow ... from overheating, do not operate it can cause serious burns or weld the metal object to the system. Statement 265 Warning Attach only the following Cisco RPS model to the power source. and 48-Port Switches) Warnings These warnings are translated into several languages in an area that is not connected...
Statement 43 Warning Do not stack the chassis on the back of 113•F (45•C). Statement 1001 Warning Read the installation instructions before beginning installation. To prevent airflow restriction, allow ... from overheating, do not operate it can cause serious burns or weld the metal object to the system. Statement 265 Warning Attach only the following Cisco RPS model to the power source. and 48-Port Switches) Warnings These warnings are translated into several languages in an area that is not connected...
Hardware Installation Guide
Page 56
Statement 43 Warning Do not stack the chassis on equipment that the system remains stable. Statement 1019 Catalyst 2960 Switch Hardware Installation Guide 3-2 OL-7075-09 If the chassis falls, it ...
Statement 43 Warning Do not stack the chassis on equipment that the system remains stable. Statement 1019 Catalyst 2960 Switch Hardware Installation Guide 3-2 OL-7075-09 If the chassis falls, it ...
Hardware Installation Guide
Page 58
...optic cable, you can use these conditions - To order a cable guard, contact your Cisco representative and use to avoid overloading the receiver. You can easily read the front-panel indicators...and 48-Port Switches)." Preparing for Installation Chapter 3 Switch Installation (8-Port Switches) • Do not stack switches or place switches side-by at least 3 inches (7.6 cm) of clearance from each other. ...; Catalyst 2960-8TC-L, 2960-8TC-S, and 2960PD-8TT-L switches cable guard part number: CBLGRD-C2960-8TC= • Catalyst 2960G-8TC-L switch cable guard part number: CBLGRD-C2960G-8TC= The...
...optic cable, you can use these conditions - To order a cable guard, contact your Cisco representative and use to avoid overloading the receiver. You can easily read the front-panel indicators...and 48-Port Switches)." Preparing for Installation Chapter 3 Switch Installation (8-Port Switches) • Do not stack switches or place switches side-by at least 3 inches (7.6 cm) of clearance from each other. ...; Catalyst 2960-8TC-L, 2960-8TC-S, and 2960PD-8TT-L switches cable guard part number: CBLGRD-C2960-8TC= • Catalyst 2960G-8TC-L switch cable guard part number: CBLGRD-C2960G-8TC= The...
Hardware Installation Guide
Page 60
... openings to complete the installation: 1. Step 3 Place the switch on all sides by -side unless they are separated on the desk or shelf. Do not stack switches or place switches side-by at least 3 inches (7.6 cm) of the switch. Do not place any items on the desk or shelf, do not...
... openings to complete the installation: 1. Step 3 Place the switch on all sides by -side unless they are separated on the desk or shelf. Do not stack switches or place switches side-by at least 3 inches (7.6 cm) of the switch. Do not place any items on the desk or shelf, do not...
Hardware Installation Guide
Page 61
..., as shown in the three screw template slots. Do not place any items on all sides with Mounting Screws) This section is installed. Do not stack switches or place switches side-by -side slots face the front of the desk or shelf after the switch is specific to the desk or...
..., as shown in the three screw template slots. Do not place any items on all sides with Mounting Screws) This section is installed. Do not stack switches or place switches side-by -side slots face the front of the desk or shelf after the switch is specific to the desk or...
Hardware Installation Guide
Page 107
...See SNMP SNMP network management platforms 1-22 software switch management 1-22 specifications A-1 speed, troubleshooting 4-4 stacking the chassis warning 2-2, 3-2 straight-through cable pinout four twisted-pair 1000BASE-T ports B-6 two twisted...spanning tree loops 4-4 speed, duplex, and autonegotiation 4-4 switch performance 4-4 troubleshooting spanning tree loops 4-4 W wall-mounting 2-11, 3-16 warnings attaching the Cisco RPS 2-2, 2-6 circuit protection 2-3 class 1 laser product 2-3, 3-2 disconnecting device 2-3 Ethernet cables 2-2, 3-2 Ethernet ports 3-3 ground connection 2-4, 3-3 grounded ...
...See SNMP SNMP network management platforms 1-22 software switch management 1-22 specifications A-1 speed, troubleshooting 4-4 stacking the chassis warning 2-2, 3-2 straight-through cable pinout four twisted-pair 1000BASE-T ports B-6 two twisted...spanning tree loops 4-4 speed, duplex, and autonegotiation 4-4 switch performance 4-4 troubleshooting spanning tree loops 4-4 W wall-mounting 2-11, 3-16 warnings attaching the Cisco RPS 2-2, 2-6 circuit protection 2-3 class 1 laser product 2-3, 3-2 disconnecting device 2-3 Ethernet cables 2-2, 3-2 Ethernet ports 3-3 ground connection 2-4, 3-3 grounded ...