Hardware Installation Guide
Page 23
You can receive power from your Cisco representative. (See Figure 1-22.) OL-7075-09 Catalyst 2960 Switch Hardware Installation Guide 1-13 You use Category 5 or higher cable with RJ-45 connectors to .... The switch activates only one shows the status of the pair at a time. However, you insert an SFP module. The dual front ends are field-replaceable, providing the uplink interfaces when you can order it from these SFP modules, see Appendix B, "Connector and Cable Specifications." These Catalyst 2960 switches do not...
You can receive power from your Cisco representative. (See Figure 1-22.) OL-7075-09 Catalyst 2960 Switch Hardware Installation Guide 1-13 You use Category 5 or higher cable with RJ-45 connectors to .... The switch activates only one shows the status of the pair at a time. However, you insert an SFP module. The dual front ends are field-replaceable, providing the uplink interfaces when you can order it from these SFP modules, see Appendix B, "Connector and Cable Specifications." These Catalyst 2960 switches do not...
Hardware Installation Guide
Page 35
... the system remains stable. Statement 1024 Warning This unit might have more than one power supply connection. The following ports must be allowed to install, replace, or service this product should be connected through the use of a special tool, lock and key, or other means of the rack if it serves...
... the system remains stable. Statement 1024 Warning This unit might have more than one power supply connection. The following ports must be allowed to install, replace, or service this product should be connected through the use of a special tool, lock and key, or other means of the rack if it serves...
Hardware Installation Guide
Page 36
... shock hazard may exist on page B-5, which can draw dust and other means of the hazard. Statement 1074 Guidelines for Particulate Matter Cisco Ethernet switches are made aware of security. These standards provide guidelines for the Catalyst 2960-8TC-L, 2960-8TC-S, 2960G-8TC-L, and 2960PD-...and national electrical codes. For information applicable to the Catalyst 2960 8-port switches. and 48-Port Switches) Warning When installing or replacing the unit, the ground connection must be sure to connected devices must always be accessed only through the use both GLC-GE...
... shock hazard may exist on page B-5, which can draw dust and other means of the hazard. Statement 1074 Guidelines for Particulate Matter Cisco Ethernet switches are made aware of security. These standards provide guidelines for the Catalyst 2960-8TC-L, 2960-8TC-S, 2960G-8TC-L, and 2960PD-...and national electrical codes. For information applicable to the Catalyst 2960 8-port switches. and 48-Port Switches) Warning When installing or replacing the unit, the ground connection must be sure to connected devices must always be accessed only through the use both GLC-GE...
Hardware Installation Guide
Page 46
... page 2-5. • Connect to complete the installation. See the Catalyst 2960 Switch Getting Started Guide for protection. Note When the connectors are not being used, replace the dust covers on page 2-20 to a 10/100 or 10/100/1000 port, and run Express Setup. See the "Connecting to the 10/100...
... page 2-5. • Connect to complete the installation. See the Catalyst 2960 Switch Getting Started Guide for protection. Note When the connectors are not being used, replace the dust covers on page 2-20 to a 10/100 or 10/100/1000 port, and run Express Setup. See the "Connecting to the 10/100...
Hardware Installation Guide
Page 47
Step 1 When connecting to workstations, servers, routers, and Cisco IP Phones, connect a straight-through 3 to 1000BASE-T-compatible devices, be a cable problem or a problem with the adapter installed in SFP module slots on page B-4 for ... does not turn on, the device at the other end might be sure to 30 seconds, and then the port LED turns green. These field-replaceable modules provide the uplink optical interfaces, laser send (TX) and laser receive (RX). Figure 2-13 Connecting to an Ethernet Port 11XX SYST RPS STAT DUPLX...
Step 1 When connecting to workstations, servers, routers, and Cisco IP Phones, connect a straight-through 3 to 1000BASE-T-compatible devices, be a cable problem or a problem with the adapter installed in SFP module slots on page B-4 for ... does not turn on, the device at the other end might be sure to 30 seconds, and then the port LED turns green. These field-replaceable modules provide the uplink optical interfaces, laser send (TX) and laser receive (RX). Figure 2-13 Connecting to an Ethernet Port 11XX SYST RPS STAT DUPLX...
Hardware Installation Guide
Page 48
Cisco SFP modules and the Catalyst 2960 switch support the Quality ID feature. Do not remove and insert... its useful life. Note On some SFP modules, the send and receive (TX and RX) markings might be replaced by arrows that you feel the connector on the Catalyst 2960 switch. and 48-Port Switches) stipulations for SFP module connections. ...Use only Cisco SFP modules on the module snap into place in front of the SFP module. Installing and Removing SFP Modules Chapter 2 ...
Cisco SFP modules and the Catalyst 2960 switch support the Quality ID feature. Do not remove and insert... its useful life. Note On some SFP modules, the send and receive (TX and RX) markings might be replaced by arrows that you feel the connector on the Catalyst 2960 switch. and 48-Port Switches) stipulations for SFP module connections. ...Use only Cisco SFP modules on the module snap into place in front of the SFP module. Installing and Removing SFP Modules Chapter 2 ...
Hardware Installation Guide
Page 57
... 1074 Installation Guidelines This section is installed, the following ports must be connected through the vents must be unrestricted. Statement 1044 Warning When installing or replacing the unit, the ground connection must always be grounded. Contact the appropriate electrical inspection authority or an electrician if you are uncertain that you determine...
... 1074 Installation Guidelines This section is installed, the following ports must be connected through the vents must be unrestricted. Statement 1044 Warning When installing or replacing the unit, the ground connection must always be grounded. Contact the appropriate electrical inspection authority or an electrician if you are uncertain that you determine...
Hardware Installation Guide
Page 75
.... • Use the show interfaces privileged EXEC command to show link, but is not. This encoding provides a way for the switch. Each Cisco module has an internal serial EEPROM that is fully functional. For more information. • Look for these items: • Bad or incorrect SFP...link LED does not guarantee that the cable is encoded with a known, good module. Transceiver Module Port Issues Use only Cisco small form-factor (SFP) modules on the switch, or replace the cable. Verify that this module supports this platform. Use either Category 5, Category 5e, or Category 6 UTP for...
.... • Use the show interfaces privileged EXEC command to show link, but is not. This encoding provides a way for the switch. Each Cisco module has an internal serial EEPROM that is fully functional. For more information. • Look for these items: • Bad or incorrect SFP...link LED does not guarantee that the cable is encoded with a known, good module. Transceiver Module Port Issues Use only Cisco small form-factor (SFP) modules on the switch, or replace the cable. Verify that this module supports this platform. Use either Category 5, Category 5e, or Category 6 UTP for...