Cisco WES610N Support and Manuals
Get Help and Manuals for this Cisco item
View All Support Options Below
Free Cisco WES610N manuals!
Problems with Cisco WES610N?
Ask a Question
Free Cisco WES610N manuals!
Problems with Cisco WES610N?
Ask a Question
Most Recent Cisco WES610N Questions
Wes61on Bridge
WES61ON was working fine. I now have blinking orange light
WES61ON was working fine. I now have blinking orange light
(Posted by rwogle213 3 years ago)
Cisco WES610N Videos
UnBoxing Cisco Linksys WES610N - Entertainment Bridge
Duration: 1:56
Total Views: 835
Duration: 1:56
Total Views: 835
Popular Cisco WES610N Manual Pages
User Manual - Page 3
...the Ethernet port(s). The LED flashes when the bridge is a wireless connection. Wi-Fi Protected Setup Button If your wireless network. If there is off, and then try again. Linksys WES610N/WET610N
Product Overview
Thank you can connect any Wireless-N, -G, -A, or -B router or access point. To configure advanced settings, use Wi-Fi Protected Setup, refer to your router supports...
User Manual - Page 4
Power The Power port connects the bridge to a computer or other Ethernet network device.
Linksys WES610N/WET610N
Ports panel
WES610N
WET610N
Ethernet The Ethernet port(s) connects the bridge to the included power adapter.
Reset There are two ways to reset the bridge's factory defaults.
Either press and hold the Reset button for approximately five seconds, or restore the defaults...
User Manual - Page 5
...the default wireless network name or SSID
Wireless devices have a default password set by the factory. Linksys wireless products use them at a rapid pace. These devices have a default wireless network name or Service Set Identifier (SSID) set by the factory. The MAC address is an older encryption standard and may be hard to access your wireless device and change the wireless network...
User Manual - Page 7
...The browser-based utility has these main tabs: Setup, Wireless, Administration, and Status.
Note If the password request screen does not appear, wait two minutes and try again.
6 Linksys WES610N/WET610N
Advanced Configuration
After setting up the bridge by following the steps on the CD folder, the bridge will be set to a specific IP address. 1. In the Subnet mask field, enter 255...
User Manual - Page 8
... Wireless Settings, page 8. Use this is the Basic Setup screen. There are two ways to your network devices, then keep the default, Automatic Configuration - Select the desired language from the DHCP server (usually the network router). Linksys WES610N/WET610N
Setup > Basic Setup
The first screen that appears is your router).
If your network router supports Wi-Fi Protected Setup...
User Manual - Page 9
...the default, Disabled.
The default selection is a more advanced, more information about wireless security, refer to use any characters on the keyboard). If you should change the default SSID (linksys) to cancel your wireless router or access point. Linksys WES610N/WET610N Basic Wireless Settings
Advanced Configuration
WPA Personal
WPA is the network name shared among all devices in...
User Manual - Page 11
... Site Survey screen lists the wireless networks detected by the bridge and wireless router or access point. Click Refresh to update the on -screen information. Select To connect to begin a site survey. WPA
Network Name (SSID) The name of the bridge.) 2. Click Refresh to update the on -screen information. After the bridge has been configured, click Close. Then click Register...
User Manual - Page 12
...keys. Security Mode WEP is Auto, which allows either Open system or Shared key authentication to update the on the WMM screen are designed for authentication. Click Refresh to be adjusted by the bridge and wireless router or access point. It must have entered the security settings, click Connect. Authentication The default is automatically displayed. After you have 8-63 characters.
User Manual - Page 13
... duration after which the ADDBA setup is 0 to 1500. The default is Yes. The range is terminated, if there are no frame exchanges within this duration by the timer.
The default is No. Click Save Settings to apply your changes, or click Cancel Changes to the four access modes available. Linksys WES610N/WET610N
WMM
Access Mode
You can assign different...
User Manual - Page 15
... by some IPTV streams.
Re-establish Ethernet connection when initiating wireless connection To trigger DHCP discovery from the receiving device.
This feature also supports all the HT devices to the bridge's browser-based utility. Select the percentage you specify. To use : 12%, 25%, 50%, or 100%. Percentage of maximal transmit power This option sets the percentage of 10 dB. For...
User Manual - Page 16
...restore the bridge's configuration to Reboot.
Before upgrading the firmware, download the bridge's firmware upgrade file from the Linksys website, www.Linksys.com/support. Upgrade Firmware
Please select a file to Upgrade and follow the on-screen instructions. Then click Start to upgrade the firmware Click Browse and select the firmware upgrade file.
Administration > Factory Defaults
Use...
User Manual - Page 17
... router (or access point) is displayed. BSSID The wireless MAC address of your wireless network is displayed. Wide Channel Depending on your wireless network is displayed. Advanced Configuration
Radio Band The radio band of your local, Ethernet network, is displayed. If you selected Wide - 40MHz Channel for your wireless network is displayed. Linksys WES610N/WET610N
Bridge...
User Manual - Page 18
....com/support
17
If you want the bridge to the bridge. •• Make sure that you are using compatible IP addresses. Check the following :
•• The password is case-sensitive.
From the Network Connection Type drop-down menu, select Static IP. 4. All other wired, Ethernet device connected to always use its factory default, admin. Linksys WES610N/WET610N...
User Manual - Page 19
Linksys WES610N/WET610N
Specifications
WES610N
Model Standards LEDs Ports Buttons Cabling Type Antennas Antenna Connector Type Detachable (Yes/No) Modulations
RF Pwr (EIRP) in dBm
Receive Sensitivity
Antenna Gain in dBi Wireless Security Security Key Bits
WES610N
IEEE 802.3u, 802.11g, 802.11b, 802.11a, 802.11n
Power, Ethernet, Wi-Fi Protected Setup™, Wireless, individual Ethernet link and...
User Manual - Page 20
Linksys WES610N/WET610N
WET610N
Model
WET610N
Standards
IEEE 802.3u, 802.11g, 802.11b, 802.11a, 802.11n
LEDs
Power, Ethernet, Wi-Fi Protected Setup™, Wireless
Ports
Ethernet, Power
Buttons
Reset, Wi-Fi Protected Setup
Cabling Type
CAT5e
Antennas
3 (internal)
Antenna Connector Type N/A
Detachable (Yes/No)
No
Modulations
802.11a: OFDM/BPSK, QPSK, 16-QAM, 64-QAM 802.11b: CCK...
Cisco WES610N Reviews
We have not received any reviews for Cisco yet.