Cisco WES610N Support Question
Cisco WES610N Support Question
Find answers below for this question about Cisco WES610N.Need a Cisco WES610N manual? We have 1 online manual for this item!
Current Answers
Answer #1: Posted by BusterDoogen on October 9th, 2015 12:45 PM
BusterDoogen
Member since:
October 30th, 2011 Points: 28,565,407
Member since:
October 30th, 2011 Points: 28,565,407
Default IP address:169.254.1.250. More info here.
I hope this is helpful to you!
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful. Please feel free to submit further info for your question, if a solution was not provided. I appreciate the opportunity to serve you!
Related Cisco WES610N Manual Pages
User Manual - Page 3
.../Amber) The LED flashes blue for choosing the Linksys Dual-Band N Entertainment Bridge. Wi-Fi Protected Setup Button If your wireless network.
Linksys WES610N/WET610N
Product Overview
Thank you can connect any Wireless-N, -G, -A, or -B router or access point. Make sure the network router supports Wi‑Fi Protected Setup. Power (Blue) The Power...
User Manual - Page 4
... a reset button on the back port panel. Product Overview 3 Linksys WES610N/WET610N
Ports panel
WES610N
WET610N
Ethernet The Ethernet port(s) connects the bridge to reset the bridge's factory defaults. Reset There are two ways to a computer or other Ethernet network device. The WES610N has four ports, and the WET610N has a single port.
Either press...
User Manual - Page 5
...Internet access are convenient and easy to enable Media Access Control (MAC) address filtering. Some applications may open file sharing without your network settings.
Hackers know these defaults and may be more secure than a traditional wired network.
Linksys WES610N/WET610N
Wireless Security Checklist
Wireless networks are adopting them to every networking device. Change the...
User Manual - Page 6
..., during vacations).
•• Use strong passphrases that can be found in length.
Linksys WES610N/WET610N
Additional Security Tips
•• Keep wireless routers, access points, or gateways away from exterior walls and windows.
•• Turn wireless routers, access points, or gateways off when they are not being used (at least eight...
User Manual - Page 7
... IP address (the default setting is 169.254.1.250)in the DHCP clients table of the main tabs.
Linksys WES610N/...IP address instead.)
Note If you can reset the bridge; The bridge will see a similar screen.) Leave the User name field blank. If you created during the Setup Wizard. In the Subnet mask field, enter 255.255.0.0. The browser-based utility has these main tabs: Setup, Wireless...
User Manual - Page 8
... your network has a DHCP server, such as your wireless network, select Manual. Wireless > Basic Wireless Settings
Use the Basic Wireless Settings screen to Wi-Fi Protected Setup, page 9.
7 Linksys WES610N/WET610N
Setup > Basic Setup
The first screen that appears is found, then the bridge will request an IP address from the DHCP server (usually the network router...
User Manual - Page 9
..., with dynamic encryption keys.
WPA2 Personal
WPA2 is a more advanced, more information about wireless security, refer to cancel your wireless router or access point.
The default selection is a security standard stronger than WEP (Wired Equivalent Privacy). Linksys WES610N/WET610N Basic Wireless Settings
Advanced Configuration
WPA Personal
WPA is AES.
8 Network Name (SSID) The SSID...
User Manual - Page 10
... your network. Encryption Select a level of your changes.
The default is the transmit key used .
Click or press the Wi-... available. Select Shared to be used by the bridge and wireless router or access point.
The Wi-Fi Protected Setup screen displays... recipient do not use a WEP key for authentication. Linksys WES610N/WET610N
Passphrase Enter the key shared by the bridge. WEP...
User Manual - Page 11
... Name The network name or SSID of wireless networks detected by the bridge and wireless router or access point. The security method used by the bridge. The Wireless Network Site Survey screen lists the wireless networks detected by the wireless network is displayed. After you have 8-63 characters. Linksys WES610N/WET610N
Method #2
Use this method if...
User Manual - Page 12
Linksys WES610N/WET610N
WPA2
Network Name (SSID) The name of WEP encryption, 40/64 bits (10 ... key of the network you selected is automatically displayed. Authentication The default is automatically displayed. Select Open to be adjusted by an expert administrator as incorrect settings can reduce wireless performance. the sender and recipient use open system authentication; These settings...
User Manual - Page 13
... 16000. Accept Aggregation This option defines whether or not the MAC layer will accept an ADDBA request. The default is 12000. Linksys WES610N/WET610N
WMM
Access Mode
You can assign different settings to cancel your changes. Size of Packet in Aggregation This option defines the minimum size (in ...
User Manual - Page 14
... Advanced Configuration
ADDBA Timeout This option defines the duration after which disables the timeout. Wireless > Advanced Wireless Settings
Configure the bridge's advanced wireless functions.
Otherwise, select No.
13 Linksys WES610N/WET610N
Max. The default is 0 to 100 ms. The default is Yes.
Timeout Internal This option defines the timeout period in the aggregate. The...
User Manual - Page 15
... option includes acknowledgement from the IP DSCP/TOS field to the bridge's browser-based utility. Keep the default, Enabled, to allow wireless access to the bridge's browser-based utility, or select Disabled to block wireless access to the web‑based utility, backup of the configuration file, and reboot. Linksys WES610N/WET610N
ERP Protection Type...
User Manual - Page 16
Linksys WES610N/WET610N
Restore Click Browse and select the configuration file. Advanced Configuration
Administration > Upgrade Firmware
Use this screen to restore the bridge's configuration to Upgrade and follow the on-screen instructions. Factory Defaults
Restore All Settings To reset the bridge's settings to upgrade the bridge's firmware. Then click Restore Configurations.
...
User Manual - Page 17
... 100% is the strongest signal strength possible; 0% is displayed. IP Address The bridge's IP Address, as seen on your wireless network is displayed.
16 Linksys WES610N/WET610N
Bridge Information
Firmware Version The bridge's current firmware is displayed.
BSSID The wireless MAC address of your local, wireless network, is the weakest possible. Security The security method of...
User Manual - Page 18
Complete the Static IP Address, Subnet Mask, and Default Gateway fields. 5. Troubleshooting
•• Make sure all devices on -screen. The browser-based utility does not accept your web browser, click Refresh. If the new settings are using compatible IP addresses.
On the Basic Wireless Settings screen, make changes through the browser-based utility, the new settings...
User Manual - Page 19
... (Yes/No) Modulations
RF Pwr (EIRP) in dBm
Receive Sensitivity
Antenna Gain in dBi Wireless Security Security Key Bits
WES610N
IEEE 802.3u, 802.11g, 802.11b, 802.11a, 802.11n
Power, Ethernet, Wi-Fi Protected Setup™, Wireless, individual Ethernet link and activity
Ethernet (4), Power
Reset, Wi-Fi Protected Setup
CAT5e
3 (internal...
User Manual - Page 20
Linksys WES610N/WET610N
WET610N
Model
WET610N
Standards
IEEE 802.3u, 802.11g, 802.11b, 802.11a, 802.11n
LEDs
Power, Ethernet, Wi-Fi Protected Setup™, Wireless
Ports
Ethernet, Power...dBm (typical) @ MCS15/2.4 GHz,
-69 dBm (typical) @ MCS15/5.0 GHz
Antenna Gain in dBi
1
Wireless Security
WEP, Wi-Fi Protected Access™ (WPA), Wi-Fi Protected Access™ 2 (WPA2)
Security ...
Similar Questions
What Is The Factory Default Ip Address For Cisco Air-lap1242ag-a-k9
(Posted by benPIAS 9 years ago)
What Is The Default Ip Address For Cisco Wap4410n Router
(Posted by temj 10 years ago)
Can I Change The Default Ip Address Of My E2500 Router
(Posted by irishdonhar 10 years ago)