Cisco WAP4400N - Small Business Wireless-N Access Point Support and Manuals
Get Help and Manuals for this Cisco item
View All Support Options Below
Free Cisco WAP4400N manuals!
Problems with Cisco WAP4400N?
Ask a Question
Free Cisco WAP4400N manuals!
Problems with Cisco WAP4400N?
Ask a Question
Most Recent Cisco WAP4400N Questions
I Connect Wap4400n In My Pc And Can Not Brow 192.168.1.245
(Posted by Anonymous-150316 9 years ago)
How Do You Open The Linksys Wap4400n
(Posted by StrAnupa 9 years ago)
Cannot Connect To Linksys Wap4400n
(Posted by gortan 10 years ago)
Cisco WAP4400N Videos
Cisco Small Business Wireless Access Point WAP4400N
Duration: 1:33
Total Views: 6
Duration: 1:33
Total Views: 6
Cisco Small Business Wireless Access Point WAP4400N
Duration: 1:33
Total Views: 5,267
Duration: 1:33
Total Views: 5,267
Popular Cisco WAP4400N Manual Pages
User Guide - Page 7
... finalized by this Guide to help you to 300 Mbps.
An access point allows for greater range and mobility within their firmware through www.linksys.com when 802.11n specification is sometimes called "wired". This Access Point currently can support an 11n data rate up your wireless network while also allowing you to connect the wireless network to update their transmission...
User Guide - Page 8
...the Access Point's technical specifications. This appendix describes some solutions to reduce the risks.
• Appendix C: Upgrading Firmware This appendix instructs you with Power Over Ethernet
What's in this User Guide?
Wireless-N Access Point with wireless networking.
• Appendix E: Glossary This appendix gives a brief glossary of the ways Windows can help you on how to connect...
User Guide - Page 10
...(SSID) and wireless security settings. If your data connection while moving around. The Access Point is compatible with wireless cards or adapters can talk to a wired network via the access point or wireless router. Several PCs equipped with 802.11n, 802.11g and 802.11b adapters, such as the wireless access point, or wireless router. Proper access point positioning combined with each...
User Guide - Page 15
...Wireless-G Exterior Access Point
9
Antennas and Positions
There are located on the back of your settings (including wireless security, IP address, and SSID) and replace them with Power Over Ethernet
Power Ethernet
Reset Button
The Power port connects to support 2X3 MIMO diversity in the standing position.
Figure 3-3: Stackable Position and its Antenna Setup
Chapter 3: Getting...
User Guide - Page 19
... switch (e.g. Or if there is a DHCP server connected to the switch, configure it to assign the IP address in the subnet through the DHCP. browser: an application that is admin. The Utility can be functional right out of the box with the default settings. The Access Point's default password is networked with the Access Point. Select the level of security under...
User Guide - Page 20
... tabs) will be available from client devices to control the wireless connections from most of wireless settings for this screen to use the new IP address the next time you can easily lose your Access Point to use the default password, admin. (You can connect your web browser, such as Internet Explorer or Mozilla Firefox and enter...
User Guide - Page 21
Wireless-N Access Point with WPC4400N and future Linksys client devices. Security Monitor
Use this screen to manage the Access Point. • Management. Status
You will be able to its factory default settings. • Firmware Upgrade. This screen displays wireless network settings including SSID, network mode, and wireless
channel. • System Performance. firmware: the software ...
User Guide - Page 22
... 6: Configuring the Wireless-N Access Point
This chapter is configured to change the Access Point's general settings.
In that appears is WAP4400N. You may assign any device name to the Access Point. Wireless-N Access Point with the default settings. You do not need the Utility to follow the instructions in . Basic Setup Tab
The first screen that case, Linksys recommends to start...
User Guide - Page 23
...address to set the time manually. The default is displayed on the right-hand side of the screen. User Defined NTP Server.
DHCP Figure 6-3: Setup - Time Tab The default is Disabled. Help information is to identify problems.
Time
You can access the public Internet.
Manually. The Access Point will contact the public time server to change the Access Point's time settings.
Enter...
User Guide - Page 31
... layer 2 header). The default in your Access Point automatically adjust the parameters for this Access Point. Advanced Wireless Settings Tab
This screen allows you want to permanently disable this feature as needed, when the Wireless-N/G products are not able to transmit to the appropriate queues based on Wireless-B connections. Channel Bandwidth. The default is part of IEEE 802.11e...
User Guide - Page 32
... Interval. A beacon includes the wireless networks service area, the Access Point address, the Broadcast destination addresses, a time stamp, Delivery Traffic Indicator Maps, and the Traffic Indicator Message (TIM). Higher settings allow your PC to cope with Linksys retail client cards (e.g.
IOT Mode. The default is disabled. The default is a temporary measure to enter sleep mode...
User Guide - Page 33
...The default is enabled, the Access Point will support wireless Access Points and wireless clients detection and classification.
Identify. You can enable or disable the security monitor feature here. Wireless-N Access Point with Power Over Ethernet
The Security Monitor Tab
On this screen you can enable or disable the security monitor feature of this account. Please check Linksys.com...
User Guide - Page 38
... Point is reset, you upgrade the Access Point's firmware, note all of your computer.
3.
Firmware Upgrade Tab
On this screen you restore the factory defaults. Do not upgrade the firmware unless you are experiencing problems with the Access Point or the new firmware has a feature you can restore the Access Point's factory default settings. Download the firmware upgrade file from the Linksys...
User Guide - Page 39
Click Save Settings to apply your change and the Access Point will reboot itself, or click Cancel Changes to remotely reboot the Access Point. Reboot Tab
On this screen you need to cancel your change. Reboot
Chapter 6: Configuring the Wireless-N Access Point
33
The Administration -
Help information is useful when you can reboot the Access Point. Figure 6-22: Administration...
User Guide - Page 50
... settings. Refer to the router or access point's documentation for the Administrator account.
4. Change the default password for more information.
44 Wireless-N Access Point with Power Over Ethernet
Appendix B: Wireless Security
Linksys wants to make it is available. If a hacker gets a hold of Linksys products provide several network security features, but they require specific...
Cisco WAP4400N Reviews
We have not received any reviews for Cisco yet.