Cisco SFE2010P Support and Manuals
Get Help and Manuals for this Cisco item
View All Support Options Below
Free Cisco SFE2010P manuals!
Problems with Cisco SFE2010P?
Ask a Question
Free Cisco SFE2010P manuals!
Problems with Cisco SFE2010P?
Ask a Question
Cisco SFE2010P Videos
Cisco SFE2010P $990 Price Reduction
Duration: :34
Total Views: 15
Duration: :34
Total Views: 15
Popular Cisco SFE2010P Manual Pages
Administration Guide - Page 5
.... The green Act/Link LEDs light up to a 100Mbps device. On the SFE2010P, a green PoE LED indicates that the Switch is operating properly. The Act (Activity) LEDs flash to various Linksys products over Ethernet cable.
SFE2010/SFE2010P Administration Guide
2 All customized user settings will reset to its stack ID. A green FAN LED lights up to indicate that the...
Administration Guide - Page 12
...the console interface to configure the Ethernet switch, proceed to "Console Configuration" section...Ethernet switch. Proceed as HyperTerminal.)
6. Use of the mini-GBIC module before inserting it into an electrical outlet. Connecting Devices
Connecting the Cables
CAUTION: Observe the orientation of a different power cord could damage the Ethernet switch.
7. SFE2010/SFE2010P Administration Guide...
Administration Guide - Page 18
..., left, or right. SFE2010/SFE2010P Administration Guide
15 Select an option that you configured previously. 2. Return to the previous menu or screen, or move cursor from one field to Action list. Open a command line editor and enter telnet . Leave the Password field blank.
3. When prompted to login, enter the default login and password: admin
The Switch Main Menu appears. Selecting...
Administration Guide - Page 21
... for the stack master. General Information
Use the General System Information screen to display the boot, software, and hardware firmware versions of the Ethernet switch. System Configuration. 2. SFE2010/SFE2010P Administration Guide
18 In stacking mode, this screen: 1. System Information. 3. General System Information. System Configuration. 2. From the System Information Menu, select...
Administration Guide - Page 23
...
Select Save to the Action list. 3. SFE2010/SFE2010P Administration Guide
20 Management Settings. 3. From the Management Settings Menu, choose 1. System Configuration Menu. 2. From the System Configuration Menu, select 2.
From the Switch Main Menu, select 1. To change the baud rate of the serial port: 1. Using the Console
System Configuration
Serial Port Configuration
Use the...
Administration Guide - Page 46
...Back (Select to return to screens where you can use the Upgrade/Backup IPv4 screen to download files from an IPv4 or IPv6 address.
1. From the Switch Main Menu, select 1.
IPv4 Upgrade/Backup.
File Management.
3. From the File Management Menu, select 1. SFE2010/SFE2010P Administration Guide
43 To open this screen:
1. System Configuration.
2. From the System Configuration...
Administration Guide - Page 47
... also must specify the interface type and ID.
2.
Upgrade / Backup IPv6
You can use the Upgrade/Backup IPv6 screen to the next.
File Management.
3.
To download a file from one
field to download files from an IPv6 address. SFE2010/SFE2010P Administration Guide
44 Using the Console
System Configuration
To enter the IPv4 Upgrade/Backup file name and location: 1. To enter...
Administration Guide - Page 48
... image on the Ethernet switch: Image 1 and Image 2. Verify that the file name and location are two software images on the switch. When you copy an image to specify which image is replaced. To enter the active image settings 1.
SFE2010/SFE2010P Administration Guide
45 Active Image
There are correct. 4. The selected image will be active after Reset field. 2. Select...
Administration Guide - Page 49
... of the Ethernet switch. Restore Factory Settings. 3.
To reset stacking configuration, use the hardware reset button on the front of the Ethernet switch.
System Configuration. 2. To restore system default settings 1. SFE2010/SFE2010P Administration Guide
46 From the System Configuration Menu, select 9. Using the Console
System Configuration
Restore System Default Settings
You can...
Administration Guide - Page 50
By default, ID numbers are automatically assigned to each port on the switch.
1. System Configuration. 2. Port Status (see page 48) 0.Back (Select to return to the previous screen.) To open this screen: From the Switch Main Menu, press 2.
From the Switch Main Menu, select 1.
Stack Configuration.
PoE Status (see page 48) 2. Port Status. SFE2010/SFE2010P Administration Guide...
Administration Guide - Page 53
...all the ports on the Ethernet switch. To open this screen: 1. From the Port Status Menu, press 2. b. From the Switch Main Menu, press 3.
SFE2010/SFE2010P Administration Guide
50 Proceed as needed:
a. Field Enable Auto Neg. Poe Settings. c. PoE Settings
You can use the PoE Settings screen to scroll through the list of ports.
Using the Console
Port Configuration
To...
Administration Guide - Page 54
...the Ethernet switch is operating in Layer 2 or Layer 3 mode. When the Operation complete message appears, press the Esc key to move the cursor from this screen: From the Switch Main Menu, press 4. System Mode (Layer 2 / Layer 3) Selection
You can also configure stacking mode from one field to the Action list.
Proceed as needed:
a. SFE2010/SFE2010P Administration Guide
51...
Administration Guide - Page 55
... Reset
Stacking Mode after reboot. To open this screen: From the Switch Main Menu, press 5. SFE2010/SFE2010P Administration Guide
52 Press the Tab key to move the cursor to the
Action list. 6. Press the Esc key to move the cursor to the field, and then press the Space Bar until the
desired setting appears. Reboot the Ethernet switch...
Administration Guide - Page 56
Using the Console
Logout
Logout
The Logout command lets you are immediately logged off the Ethernet switch.
SFE2010/SFE2010P Administration Guide
53 NOTE: When you issue this command, you logout from the Ethernet switch.
Administration Guide - Page 63
...layer 3 traffic
SFE2010/SFE2010P Administration Guide
60 E
Specifications
Model
Ports
Cabling Type Switching Capacity Forwarding Capacity LEDs Stack Operation
Buttons Layer 2 options
Layer 3 options
• SFE2010 48-port 10/100 Ethernet Switch • SFE2010P 48-port 10/ 100 Ethernet Switch... 2 mini-GBIC ports Console port Auto MDI/MDI-X Autonegotiate/Manual setting RPS port for connecting...
Cisco SFE2010P Reviews
We have not received any reviews for Cisco yet.