Cisco SRW248G4P Support and Manuals
Get Help and Manuals for this Cisco item
This item is in your list!
View All Support Options Below
Free Cisco SRW248G4P manuals!
Problems with Cisco SRW248G4P?
Ask a Question
Free Cisco SRW248G4P manuals!
Problems with Cisco SRW248G4P?
Ask a Question
Popular Cisco SRW248G4P Manual Pages
User Guide - Page 12
... the System Information screen you wish to choose; User and Password Settings 4 .
System Configuration 2 . The first time you finish configuring the HyperTerminal, the Login screen appears. pressing the Enter key activates the highlighted option. Login
When you open the Console Interface, use the default username admin and leave the password blank and press the Enter key. Each...
User Guide - Page 16
...
• 1000full Supports 1000 Mbps full-duplex operation
Default: Auto-negotiation enabled; Advertised capabilities for security reasons. Chapter 4
Configuration Using the Console Interface
Back to Main Menu
Select Back to Main Menu if you want to return to advertise, or manually fix the speed, duplex mode, and flow control. Port Status
The Port Status screen allows...
User Guide - Page 19
...
System Name Specifies the name of VLAN 1.
Firmware Version The current software version is enabled via manual configuration (Static), Dynamic Host Configuration Protocol (DHCP), or Boot Protocol (BOOTP).
Select the IP Address Mode using the text field provided. You may also need to a connected PoE device. By default, all ports on the Switch are members of...
User Guide - Page 20
...Set the time zone by selecting it from the factory default set USA, Europe, or custom daylight saving time by periods. (Default: 192.168.1.254) Subnet Mask This mask identifies the host address bits used for routing to specific subnets. (Default: 255.255.255.0) Default... sends a request for event entries. Setup > Time
Set Time
Set the system time manually This option allows you to assign a...
User Guide - Page 21
...Port Management > Port Settings
Port Displays the port number. Link Status Displays the link status of the appropriate port. Port Management > Edit Port Settings
This screen allows you to edit the following information for editing port settings. Port Management > Port Settings
You can manually configure the speed, duplex mode, and flow control used by default.
48-Port 10/100 + 4-Port...
User Guide - Page 38
... to define packet classification, service tagging, and bandwidth policing, it must be specified, including standard or extended IP ACLs and MAC ACLs. (Range: 1-16 characters)
IP DSCP A DSCP value. (Range: 0-63)
IP Precedence An IP Precedence value. (Range: 0-7)
VLAN A VLAN value. (Range: 1-4094)
Add Adds the specified criteria to a specific interface by setting a CoS, DSCP, or...
Administration Guide - Page 31
...:
• Upgrade the firmware or boot code, or replace a second language, as described in Upgrade/Backup Firmware/Language section.
• Save configuration files on the switch to a location on another device as described in the Downloading or Backing-up a Configuration or Log
• Viewing Configuration Files Properties
Cisco Small Business 200 Series Smart Switch Administration Guide
32...
Administration Guide - Page 33
... and File Types section).
• TFTP Server Definition-Select whether to be replaced with a new version of that file type located on a TFTP server.
... file type. Cisco Small Business 200 Series Smart Switch Administration Guide
34 Only valid file types are shown. (The file types are :
- Managing System Files
Upgrade/Backup Firmware/Language
4
Select one link local address is supported. A link...
Administration Guide - Page 54
...; Actual Time (Static)-System time on some devices.
Cisco Small Business 200 Series Smart Switch Administration Guide
55 Optionally, enforce authentication of the SNTP sessions by using the HTTP protocol.
STEP 2 Enter these parameters:
Clock Source Settings-Select the source used when there is manual, you can enter the time here. System Time
Configuring...
Administration Guide - Page 101
... desired ports from the Edit Port Settings page. The Edit Port Settings page opens. Combo Ports Copper-Combo port connected with copper CAT5 cable, supports the following values: 10M, 100M, and 1000M (type: Copper).
- The Port Settings page opens. STEP 4 To update the port settings, select the desired port, and click Edit. Cisco Small Business 200 Series Smart Switch Administration Guide
102...
Administration Guide - Page 104
... are supported:
• Static-A LAG is static if the LACP is disabled on it . Port Management
Configuring Link Aggregation
9
• Link Aggregation Overview
• Static and Dynamic LAG Workflow
• Defining LAG Management
• Configuring LAG Settings
• Configuring LACP
Link Aggregation Overview
Link Aggregation Control Protocol (LACP) is part of the IEEE specification (802...
Administration Guide - Page 227
... default settings:
• Have a minimum length of eight characters.
• Contain characters from at least three character classes (uppercase letters, lowercase letters, numbers, and special characters available on a standard keyboard).
• Are different from the current password.
• Contain no password). Cisco Small Business 200 Series Smart Switch Administration Guide
228...
Administration Guide - Page 236
... security reasons. STEP 2 Enable or disable the following TCP/UDP services:
• HTTP-Enabled by factory default • HTTPS-Enabled by factory default The active TCP connections are also displayed in this window. Cisco Small Business 200 Series Smart Switch Administration Guide
237 Configuring Security
Configuring TCP/UDP Services
STEP 5 Click Apply, and the rule is enabled or...
Administration Guide - Page 248
...by default on it. Denial of Service Prevention > Security Suite Settings.
To configure DoS Prevention global settings and monitor SCT:
STEP 1 Click Security > Denial of Service Security Suite Settings
NOTE Before activating DoS Prevention, you must unbind all Access Control Lists (ACLs) or advanced QoS policies that are bound to enable viewing CPU resource utilization information. Cisco...
Administration Guide - Page 274
....
The Interface Settings page is displayed.
The list of determining how traffic in queues is displayed. QoS State displays whether QoS is the highest priority queue. STEP 4 Select the Port or LAG interface. Configuring QoS Queues
The switch supports four queues for this interface.
Cisco Small Business 200 Series Smart Switch Administration Guide
275 STEP...
Cisco SRW248G4P Reviews
Do you have an experience with the Cisco SRW248G4P that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Cisco yet.
Earn 750 points for your review!