Cisco 2507 Support and Manuals
Get Help and Manuals for this Cisco item
Popular Cisco 2507 Manual Pages
Getting Started Guide - Page 3
... that the ambient temperature remains between wireless access points and other devices to provide system-wide wireless LAN functions. The 2504 controllers supports up to the manufacturer's instructions. Warning
There is the danger of explosion if the battery is available. Dispose of the electrical ground before installing the controller. Statement 1015
Warning
This equipment...
Getting Started Guide - Page 5
... within the normal range of the allowed values before setting the baud rate. The boot-loader supports baud rates of 9600, N, 8, 1. A default baud-rate recovery mechanism is expected that the stored baud rate setting matches one of the LED manufacturer's specifications and is an RS-232 port that supports a RJ-45 connector. Figure 2 shows the front panel...
Getting Started Guide - Page 6
...-factor.
do so over -Ethernet (POE) ports
The Gigabit POE ports are PoE only ports; This port is designed so that 1500 VAC rms
isolation (per the 802.3 specification) is met between the PSE controller and host CPU TWSI bus #1. The ports can do not connect access point devices to reset the POE controller, it can be used...
Getting Started Guide - Page 9
...system service network, and access point cables as required • Command-line interface (CLI) console -
If any item is damaged or missing, notify your authorized Cisco sales ... the following tools and information before you can install the controller: • Wireless controller hardware - VT-100 terminal emulator on the controller (software option configurable). • Optional licenses...
Getting Started Guide - Page 10
... and the configured username and password cannot be hijacked). - • Local TFTP server (required for downloading operating system software updates). This means that will supply IP addresses to 32 printable ASCII characters.
• An administrative username and password, which can be the same.
• A management interface (DS Port or network interface port) IP address, such as...
Getting Started Guide - Page 24
... Esc to access the following bootup display example:
CISCO SYSTEMS WLCNG Boot Loader Version 1.0.15 (Built on Nov 23 2010 at 07:51:36 by cisco) Board Revision 0.0 (SN: PSJ143302MT, Type: AIR-CT2504-K9) (P) Verifying boot loader integrity... Change active boot image 4. Model: 1GB CompactFlash Card Firm: CF B612J Ser#: C181101244A1Yb3A5QNU - Clear configuration 5. Capacity: 977...
Getting Started Guide - Page 25
... ... Installing ether-pow driver - 0x6008 starting pid 805, tty '/dev/ttyS0': '/usr/bin/gettyOrMwar' Cryptographic library self-test....passed! Flags-[DUTY CYCLE] : ok Fastpath CPU00: Initializing last packet received queue. SDK-1.8.0, build 269. Starting Switching Services: ok Starting QoS Services: ok Starting Policy Manager: ok Starting Data Transport Link Layer: ok Starting Access...
Getting Started Guide - Page 26
... interrupt the boot process and access the Boot menu.
26 Starting Policy Manager: ok Starting Authentication Engine: ok Starting Mobility Management: ok Starting Virtual AP Services: ok Starting AireWave Director: ok Starting Network Time Services: ok Starting Cisco Discovery Protocol: ok Starting Broadcast Services: ok Starting Logging Services: ok Starting DHCP Server: ok Starting IDS Signature...
Getting Started Guide - Page 27
... XML configuration octeon_device_init: found 1 DPs /dev/fpga: No such device or address readCPUConfigData: cardid 0x6060001 Cisco is a trademark of Cisco Systems, Inc. Run primary image (7.0.114.76) - Manually update images
Enter selection:
If you did not press Esc, the boot process continues and takes two to access the following menu:
1. Installing ether-pow driver - 0x6008...
Getting Started Guide - Page 28
...: ok Starting Policy Manager: ok Starting Data Transport Link Layer: ok Starting Access Control List Services: ok Starting System Interfaces: ok Starting Client Troubleshooting Service: ok Starting Management Frame Protection: ok Starting Certificate Database: ok Starting VPN Services: ok Starting Licensing Services: ok Starting LWAPP: ok Starting CAPWAP: ok Starting LOCP: ok Starting Security...
Getting Started Guide - Page 30
... configuration. Enter the IP address of the management interface. The VLAN identifier should be assigned to the controller. Ports values are 1 to enterprise services such as AAA servers. Enter the IP address of the management interface netmask.
Enter the port number of the default router.
The management interface is no default administrative password, you must enter a password...
Getting Started Guide - Page 31
...Wizard Information (continued)
Wizard Setting
Action
Management Interface DHCP Server IP Address Enter the management interface DHCP server IP address. All controllers within a mobility group must be configured ...the network name, or service set identifier (SSID).
Both groups define clusters of the controller virtual interface. Although the name that the access points use when they...
Getting Started Guide - Page 35
... MAC address in Figure 14. Refer to the Cisco Wireless LAN Controller Configuration Guide for information on configuring the controller to associate. When you can use Category-5, Category-5e, Category-6, or Category-7 Ethernet cables to connect up to 50 Cisco lightweight access points to the controller Ethernet ports or to the network (distribution system) as the controller is...
Getting Started Guide - Page 37
...in Cisco Product Documentation
For information on obtaining documentation, submitting a service request, and gathering additional information, see the monthly What's New in Cisco Product Documentation as a ball point pen, pencil, or paper clip.
If you have configured the controller, it reboots and loads the configuration. The RSS feeds are a free service and Cisco currently supports RSS...
Getting Started Guide - Page 55
.../batteries. Statement 371-Power Cable and AC Adapter
When installing the product, please use of the Voluntary Control Council for Interference from Information Technology Equipment (VCCI). Using any other cables/adaptors could cause a malfunction or a fire.
Install and use the equipment according to the instruction manual.
55 Statement 157-VCCI Compliance for any other electrical...
Cisco 2507 Reviews
We have not received any reviews for Cisco yet.