Canon REALiS WUX400ST Pro AV Support and Manuals
Get Help and Manuals for this Canon item
View All Support Options Below
Free Canon REALiS WUX400ST Pro AV manuals!
Problems with Canon REALiS WUX400ST Pro AV?
Ask a Question
Free Canon REALiS WUX400ST Pro AV manuals!
Problems with Canon REALiS WUX400ST Pro AV?
Ask a Question
Popular Canon REALiS WUX400ST Pro AV Manual Pages
User Manual - Page 16
Safety Instructions
Before installing and operating the projector, read this manual again, check operations and cable connections, and try the solutions in the "Troubleshooting" section in the back of Electronic Computer / Data Processing Equipment, ANSI / NFPA 75.
16 If the problem still persists, contact the Canon Customer Support Center. THIS SYMBOL INDICATES THAT DANGEROUS VOLTAGE ...
User Manual - Page 18
... never be covered with care. This projector should be placed in a built-in installation such as they may result in the rear and front of the cabinet are provided for long periods of time, unplug it is provided.
18 Safety Instructions
■ READ AND KEEP THIS OWNER'S MANUAL FOR LATER USE. Follow all of...
User Manual - Page 26
.... • Useful life of lamps varies widely from lamp to fall or be scattered inside the projector. Failure to the side of maintenance costs, contact the Canon Customer Support Center. Always request service from doing so. During replacement, stand to do not use or after the lamp's useful life has expired may damage
lamps (which...
User Manual - Page 32
... 15-pin)
• Power cord (1.8 m / 5.9')
For Continental Europe
• User's Manual (CD-ROM)
For the U.S.A. and Canada
• Warranty Card • Important Information
32 However, some buttons are not supported with the projector.
• Remote control
• Batteries for the remote control
(part No.: RS-RC06)
Optional remote controls are also available (RS-RC04...
User Manual - Page 70
...adjust the corner. You can now reset the correction selected in the [Install settings] menu (WUX400ST/WX450ST).
■ Resetting the Keystone Adjustment
Perform the following steps to reset the keystone adjustment. Remote control
Projector
3 Press the pointer buttons to display the [Keystone reset] window. Remote control
Projector
4 When you subsequently use [Zoom] (P149) in the keystone...
User Manual - Page 88
...; For the signal types supported by the projector, see the table on page 292. Select an input signal corresponding to accept your setting.
Setting Display Status (Input Settings)
Setup Using Auto PC
> [Input settings] > [Auto PC]
HDMI Digital PC
Component Analog PC
LAN USB
Automatically adjusts display position misalignment and screen flickering. Press the OK button to the...
User Manual - Page 120
... which reminds you of the time remaining until the lamp must be replaced. For details about how to replace or clean the filter, refer to [Full power].
Press the MENU button or EXIT button.
120 This value is selected. Customizing System Operation (System Settings)
• The lamp counter provides an estimate of the time for cleaning...
User Manual - Page 128
Specifically, refer to instructions for the image projected to return to normal.
■ At Altitudes above 2,300 m (7,545.8'), Adjust the Settings
Projector settings must be adjusted when using the projector at altitudes of the room rises suddenly, moisture in the air may condense on the ceiling or installed in the [Install settings] menu.
■ When Using Mounted on the Ceiling...
User Manual - Page 129
... any direction*1, as shown below. Installation and Maintenance Installation
Before Installation
■ Install Facing in the Correct Direction
The projector can be no more than 10° from the vertical axis.*2
If installing the
projector on its side.
Specifically, for upward or downward projection, refer to instructions for installing the projector in ways other than ceiling...
User Manual - Page 201
... be displayed again if you select [No] in the [System
settings] menu. (P119) • This screen is not displayed when [Lamp warning display] is
displayed. • When you press the POWER button, the "Push POWER button again to turn off
power." Installation and Maintenance Maintenance
Replacing the Lamp
When the usage time of the lamp...
User Manual - Page 202
.... Replacing the Lamp
1 Turn off the projector, wait until the cooling fan stops, disconnect the power plug from the electrical outlet, and let the projector stand for further information.
Additionally, with ceiling-mounted projectors, the lamp may break
during use if it . If the lamp breaks, contact the Canon Customer Support Center or follow the instructions on...
User Manual - Page 204
... on the projector and gently push the lamp cover to attach it.
204 Bring up the menu and select [System settings] -
[Other settings] - [Lamp counter].
8 Select [Reset] - [Yes] to reset the lamp counter.
• We recommend cleaning or replacing the air filter (part no.: RS-FL02) when you replace the lamp.
• Contact the Canon Customer Support Center for...
User Manual - Page 211
... required to the projector. For instructions on how to "Completing Computer Settings" (P178). Networked Multi-Projection Networked Multi-Projection Overview
Installation
Installation
The application is stored in order. - Refer to "Windows Firewall" (P215) for more detailed information on accessing the projector's web screen with a browser, refer to set the firewall manually. To check...
User Manual - Page 282
... projector is connected to a problem with the input terminal has not been performed correctly. Turn on the external monitor output on the notebook computer correctly. To turn on image output by holding down the Windows logo key and pressing the [P] key. (P145) The combination of keys used to the manual that displayed on the model...
User Manual - Page 312
Menu Configuration
HDMI In Language
Other settings Password settings Register password Gamma restore Lamp counter Air filter counter Firmware Factory defaults
Network Settings Menu
Network settings lock Network password setting Register network password Network function (wired) Network standby settings Detailed settings (wired)
IP address
Auto* Computer
English German French Italian Spanish ...
Canon REALiS WUX400ST Pro AV Reviews
We have not received any reviews for Canon yet.