Brother International XL3700 Support and Manuals
Get Help and Manuals for this Brother International item
This item is in your list!
View All Support Options Below
Free Brother International XL3700 manuals!
Problems with Brother International XL3700?
Ask a Question
Free Brother International XL3700 manuals!
Problems with Brother International XL3700?
Ask a Question
Popular Brother International XL3700 Manual Pages
Operation Manual - Page 2
... as an unsteady or slanted table, otherwise the machine may fall, resulting in the instruction manual:
• To unplug the machine, switch the machine to the symbol "O" position to... the machine and foot control free from all moving parts.
Return the machine to the nearest authorized dealer or service center for examination, repair, electrical or mechanical adjustment.
• While the ...
Operation Manual - Page 3
... the operation manual when replacing or installing any adjustments in the needle area.
• Do not use of the appliance in a safe way and understand the hazards involved.
For additional product information, visit our web site at www.brother.com
SAVE THESE INSTRUCTIONS
This machine is not intended for use outdoors.
7 For a longer service life:
•...
Operation Manual - Page 4
..., rating as marked on storing the machine 47 Cleaning 47
TROUBLESHOOTING 49 INDEX 52
3 Never use a fuse
approved by ASTA to obtain...models equipped with a quick-set bobbin 18 Upper threading 19 Using the needle threader (for the plug supplied with a twin needle (Option 27 Thread tension 29
3. FOR USERS IN THE UK, EIRE, MALTA AND CYPRUS ONLY IMPORTANT
• In the event of replacing...
Operation Manual - Page 5
...
1
Zigzag foot "J" (on the machine model. Part Name
6
Bobbin (One is on machine)
7
Needle set (90/14 needle)
8 Oval screwdriver
9 Foot controller
Part Code
Americas Others
SA156
SFB: XA5539-151
3-piece set: XE5328-001 2-piece set: XE7064-001
XE5241-001
See page 5
Note
● The included accessories vary depending on machine)
2 Buttonhole foot "A"
3 Zipper foot "I"
4 Darning...
Operation Manual - Page 6
... flat bed attachment. Contact your dealer or the nearest authorized service center. KNOWING YOUR SEWING MACHINE
THE MAIN PARTS
654 3 2 1 7
E
8
9
D
0
A
C B
1 Bobbin winder (Page 15) This winds the thread onto the bobbin for 220-240V area The foot controller part code differs depending on certain models.)
A Flat bed attachment with accessory compartment (Page 5)
B Presser foot (Page...
Operation Manual - Page 16
... machine or bobbins of the same type (part code: SA156, SFB: XA5539-151). If you , in the wrong place, or is set incorrectly, the thread may cause damage to ...the machine. Only use bobbins from the spool 2 with this machine.
Actual size
11.5 mm (7/16 inch)
This model
Other models
1
1 Pull the...thread on the thread guide.
Operation Manual - Page 18
... turning the 2 handwheel toward you. If you accidentally step on using the quick-set the bobbin so the thread unrolls in the wrong direction, it may break the... the presser foot lever. CAUTION
● Make sure you set bobbin, see page 18. Remove the bobbin cover by the arrow.
1
2
1 Wound evenly 2 Wound poorly
Lower threading
Install the bobbin wound with your finger, and then
pass the ...
Operation Manual - Page 19
Replace the bobbin cover. Lower threading (for models equipped with a quick-set bobbin)
Install the bobbin wound with the cutter (3).
• At this time, check that... inserted through the slit (1 and 2). Then, pull the thread toward the rear of the machine (as shown, guide the
thread through
1
the tension-adjusting spring of the bobbin
case, it with thread. Put the 6 projection into...
Operation Manual - Page 20
...YOUR SEWING MACHINE
Upper threading
2
2
3 4
1 5
1 Spool pin 2 Thread guide (back) 3 Thread guide (front)
4 Thread take-up the spool pin and put a spool of 20 or...handwheel 3 toward you (counterclockwise) so that the
mark on the wheel points up. • If the needle is set incorrectly, the thread may tangle on the spool pin and cause the needle to "FABRIC, THREAD, AND NEEDLE COMBINATIONS...
Operation Manual - Page 21
...Feed the upper thread as shown in the 6 following illustration.
1
1 Needle bar thread guide
Make sure you guide the thread through 7 the thread take-up lever from right to left
as shown in the... inches)
Note
● Make sure you may cause sewing problems.
20 While holding the
1
• Make sure that the mark on the thread guide.
• The thread can easily be wrapped around the thread...
Operation Manual - Page 24
... along the slit in the
2 direction of the machine under the presser foot.
1 2
1 Upper thread 2 Lower thread
■ For models equipped with a quick-set bobbin You can draw up the bobbin thread. Replace the bobbin cover. 4
23 Before you can begin sewing immediately without cutting it there without drawing up the lower thread...
Operation Manual - Page 29
... using the thread from front to
thread the twin needle. Install the second thread spool onto the extra spool pin.
1 ...passes through the eye of the needle bar thread guide
3 Needle bar thread guide
Attach zigzag foot "J". 3 For details on changing...set above the needle before you threaded the left needle. 1 Follow the same instructions for threading a
single needle (see page 19). Note
Models...
Operation Manual - Page 48
... using it may result, for example, rust caused by the user.
Using the oval screwdriver, remove the 4 two screws. If problems occur, such as
shown in any of the locations described below, otherwise damage to the machine may reduce its efficiency. Storing this... period of time without using the machine, and contact your authorized dealer or the nearest authorized service center.
Operation Manual - Page 50
... problems by yourself.
The upper thread was not threaded correctly. The upper thread tension is pushed to sew. You have not used the foot controller properly.
How to the left. Correctly install the needle. Replace the needle. Lightly guide the fabric. Replace the bobbin case. Loosen the upper thread tension. Visit us at " http://solutions.brother...
Operation Manual - Page 51
...your retailer or the nearest authorized service center.
- Replace the bobbin case. Wind the bobbin thread properly.
15
The lower
The bobbin is incorrectly installed. Remove the tangled thread and clean...is correct
appropriate for the type of stitch that are being sewn, the stitch is set incorrectly.
The thread is Sew with stabilizer material under the
not being sewn, the ...
Brother International XL3700 Reviews
Do you have an experience with the Brother International XL3700 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Brother International yet.
Earn 750 points for your review!