Brother International SB4138 Support and Manuals
Get Help and Manuals for this Brother International item
View All Support Options Below
Free Brother International SB4138 manuals!
Problems with Brother International SB4138?
Ask a Question
Free Brother International SB4138 manuals!
Problems with Brother International SB4138?
Ask a Question
Popular Brother International SB4138 Manual Pages
Users Manual - English - Page 3
... cover included with your machine cannot be installed on the machine.
(XE8992-001)
(XE8878-001)
2
Utility stitches
Decorative stitches (For models with this kit was purchased.
Bobbin case (gray) (XE8298-001)
Bobbin cover with tabs (*See Note.)
Screwdriver (small) (X55468-051)
CD-ROM (Contains the Operation Manual and the Templates for freemotion sewing.) (USA/CANADA: XE9382...
Operation Manual - Page 4
... consult the operation manual when replacing or installing any opening. • Do not operate where aerosol (spray) products are subject to the danger of this manual. If the problem persists, please consult your work area clear:
• Never operate the machine with the bag due to change without notice. The contents of this manual and specifications of suffocation...
Operation Manual - Page 6
Contents
IMPORTANT SAFETY INSTRUCTIONS 1 Introduction ...7 Sewing Machine Features ...7 Accessories ...8
Included accessories ...8 Optional accessories ...9
Names of Machine Parts and Their Functions 10
Front view ...10 Needle and presser foot section ...11 Right-side/rear view ...11 Operation buttons ...12 Operation panel ...13
GETTING READY
15
Turning the Machine On/Off 16
Power supply ...
Operation Manual - Page 9
... (page 65).
Sewing Machine Features
a Easy upper threading Since the spool can be installed at the end of...manual for future reference. c Automatic thread-cutting The sewing machine can quickly be set to raise and lower the presser foot with thread (page 22). Before using this sewing machine, carefully read the "IMPORTANT SAFETY INSTRUCTIONS" (page 1), and then study this sewing machine...
Operation Manual - Page 12
... take -up lever.
10 Names of Machine Parts and Their Functions
The names of the various parts of thread on the spool pin. Before using the sewing machine, carefully read these buttons and the slide to check the position of the machine parts. b Thread guide cover Pass the thread behind the thread guide cover when threading the upper thread...
Operation Manual - Page 15
...sewing machine is pressed, the font switches to one of Machine Parts and Their Functions 13
n Manual memory key Press this key to the previous screen. q OK key
Press this key to adjust the stitch width setting...and keys for specifying various sewing settings.
1 2 3 4 5 6 0
A
B
C
H
a LCD (liquid crystal display) Settings for the selected stitch and error messages for incorrect operations ...
Operation Manual - Page 21
... key) in the operation
X The settings screen appears. Changing the Machine Settings 19 Turn on .
Press or (Stitch width keys) until the
1
c stitch or machine attribute that you wish to set
The general procedure for changing machine settings is displayed. Changing the Machine Settings
Various sewing machine operations and sewing settings can be changed . is described below.
Operation Manual - Page 24
... may result in injuries or damage to the machine.
● The included bobbin was designed specifically for this sewing machine. Be sure to wind the thread onto the bobbin, and then insert the bobbin thread. Use of the same type (part code: SA156, SFB(XA5539-151)). GETTING READY
Winding/Installing the Bobbin
This section describes how to...
Operation Manual - Page 25
... shaft so c that the spool is inserted onto the e spool pin.
1
2
a Spool pin b Spool cap
Winding/Installing the Bobbin 23 a
Place the spool of the d arrow until it snaps into place.
1
• If the spool....
1
Open the top cover. b
Place the bobbin on the slit in the spool or the machine may become tangled around the spool pin. Turn on the shaft fits into the notch
in orange.
...
Operation Manual - Page 27
...bobbin is set to cut the thread as described. Slide the sewing speed controller to the right m to increase the bobbin winding speed and slide
to stop the machine, otherwise the sewing machine may ...guide l slit in the bobbin winder seat, and then pull
the thread to the right to a suitable length. When the foot controller is plugged in cutter)
X The thread is impossible.)
Winding/Installing...
Operation Manual - Page 28
... bobbin was designed specifically for this is indicated by marks around the tab with thread. this sewing machine.
Be sure to thread the machine as shown, lightly pull the thread to install the bobbin so that the bobbin thread should be incorrect. GETTING READY
Remove the bobbin from other models are used, the machine will not operate...
Operation Manual - Page 30
... then thread the machine. If the upper threading is indicated by a solid line on the sewing machine.
Threading the upper thread
Set the spool of thread on the sewing machine. GETTING READY
Upper...machine should be threaded is not correct, the thread may become tangled and the needle may bend or break.
CAUTION
● When threading the upper thread, carefully follow the instructions...
Operation Manual - Page 48
... pant legs. Slide the part that you are finished with free-arm sewing, c install the flat bed attachment back in its
original position. X With the flat bed attachment removed, freearm sewing is available through your brother dealer.
46 GETTING READY
Sewing Cylindrical or Large Pieces
When sewing cylindrical or large pieces of the sewing machine bed.
a
Open up the...
Operation Manual - Page 153
... direction.
• Hold the bobbin with your dealer or the nearest authorized service center. Troubleshooting
If the machine stops operating correctly, check the following possible problems before contacting us at " http://solutions.brother.com " .
For this before requesting service.
Troubleshooting 151
Frequent troubleshooting topics
Detailed causes and remedies for common...
Operation Manual - Page 162
APPENDIX
List of stitch that you wish to sew. Press the "Start/Stop" button.
Use the screwdriver to
the right.
Correctly install the spool.
A bobbin designed specifically for this machine. Replace the bobbin case. Contact your dealer or the nearest authorized service center.
The "Start/Stop" button was not pressed. Do not use the "Start/ Stop" button...
Brother International SB4138 Reviews
We have not received any reviews for Brother International yet.