Brother International Laura Ashley Innov-ís NX2000 Support and Manuals
Get Help and Manuals for this Brother International item
View All Support Options Below
Free Brother International Laura Ashley Innov-ís NX2000 manuals!
Problems with Brother International Laura Ashley Innov-ís NX2000?
Ask a Question
Free Brother International Laura Ashley Innov-ís NX2000 manuals!
Problems with Brother International Laura Ashley Innov-ís NX2000?
Ask a Question
Most Recent Brother International Laura Ashley Innov-ís NX2000 Questions
Portuguese Manual
(Posted by cacavallet 9 years ago)
Popular Brother International Laura Ashley Innov-ís NX2000 Manual Pages
Users Manual - English - Page 10
...
Memo
We recommend an upper thread tension that there is higher than the standard setting.
If sewing is equipped with automatic thread cutting turned on the fabric, bunched stitches... a stitch.
We recommend selecting a simple stitch and sewing trial stitches to the machine's Operation Manual. • Depending on , the thread may become tangled or the needle may result.
Memo
...
Users Manual - English - Page 3
...proper needle plate. tioned in this manual. SAVE THESE INSTRUCTIONS This machine is being used as..." " position when making any other user servicing adjustments men- Do not pull or push ...examination, repair, electrical or mechanical adjustment.
4. Always unplug the machine from all instructions before ...following: Read all moving parts. The machine should be replaced by pulling on cord....
Users Manual - English - Page 5
... equipment has been tested and found to comply with the instructions, may cause undesired operation. Federal Communications Commission (FCC) Declaration of Conformity (For USA Only)
Responsible Party:
Brother International Corporation 100 Somerset Corporate Boulevard Bridgewater, NJ 08807-0911 USA TEL : (908) 704-1700
declares that interference will not occur in a particular installation.
Users Manual - English - Page 6
... store anything on the foot controller. 4. Always consult the operation manual when replacing or installing any assemblies, the presser feet, needle, or other parts to inspect and adjust the machine yourself. For repair or adjustment In the event a malfunction occurs or adjustment is completed • Replacing or removing the needle or any location exposed to clean...
Users Manual - English - Page 15
... Quick Reference Guide
XE8167-001
43 Wide table
XE0802-101
44 Soft cover
XE1121-001
*1 See Circular Attachment Instruction Manual for detailed instruction.
*2 See Bobbin Work Instruction Manual for the presser foot holder is on using parts 13 and 43, refer to the instruction sheet enclosed with item.
• Always use accessories recommended for this machine model NX-2000...
Users Manual - English - Page 23
... the screen. Six categories are displayed at the top of this Operation Manual are stored in this machine. Press
to
1
see more information about that category.
■ Contents of Each Category
Names of Machine Parts and Their Functions
Sewing Basics
Troubleshooting
Getting Ready
Presser foot lever Sewing speed controller Handwheel Flat bed attachment...
Users Manual - English - Page 25
... bobbins of the same type (part code: SA156, SFB: XA5539-051).
11.5 mm (approx. 7/16 inch)
Actual size This model Other models
a Supplemental spool pin
d
Place..., medium, or small) that the thread unwinds from other models are set the
bobbin on the shaft. Getting Ready
CAUTION
• The included bobbin was designed specifically for this machine, you can conveniently be wound.
65
a...
Users Manual - English - Page 32
...SETTING CHART" at the end of this machine (part code X59296-151). c
Pass the thread through the bobbin winding thread guide. Then, slide the spool
cap as far as possible onto the supplemental
spool pin to set..., and then pass the thread
through the thread guide.
* Do not pass the thread through the needle bar thread guide, and then manually thread the needle
on
page 33). The needle ...
Users Manual - English - Page 43
...the presser foot lever. Once the trouble spot has been sewn, the presser foot
will return to break and cause injury.
Sewing Basics
The pivot setting is automatically raised so the fabric ...machine stops with the needle in the machine settings screen is set to "ON", the thickness of presser foot "J". If the fabric is automatically detected by the internal sensor so the fabric can be
fed....
Users Manual - English - Page 44
....
CAUTION
• If the stitches get bunched together, lengthen the stitch length and continue sewing. Each press of the settings as described in this manual). • If a stitch setting is changed (See "STITCH SETTING CHART" at the end of makes the stitch longer.
Otherwise, the needle may break and cause injury.
42
However, if...
Users Manual - English - Page 53
... to "STITCH SETTING CHART" at the end of this manual.
■ Using the Mirror Image Key
Press
so that they can be created. b Set the stitch length to its default settings,
press
, .... c Press
.
* To reset the selected stitch to 2.0 mm.
b Press
to
save specific settings for the straight stitch
a Press , and then select a straight stitch.
This machine is selected, a mirror ...
Users Manual - English - Page 82
...or basting to attach the appliqué to correct the problem.
■ If the Needle Does Not Catch the ... Needle Catches Too Much of these occur, follow the instructions below to the fabric. a Appliqué
a a... and length according to the shape, size and fabric quality of this manual.
a
b
a Appliqué b Fabric glue
b Press
or .... SETTING CHART" at the end of the appliqué ...
Users Manual - English - Page 144
... needle is set incorrectly. Remove the dust or lint with your sewing machine, check the following solutions. Reinstall the spool correctly. The wrong presser foot was used , the needle bar thread guide did not catch the thread, etc.). Remove the knots and tangles.
Replace the needle.
Replace the needle with a simple troubleshooting feature that are...
Users Manual - English - Page 145
...is set incorrectly.
Do not pull the fabric during sewing.
Replace the race (bobbin case), or consult your
−
presser foot. Replace the needle with a new one .
33
The thread is installed ... pass through the machine
The feed dogs are caught in the feed dogs.
TROUBLESHOOTING
Problem
Cause
Solution
Page
High-pitched sound while Dust or lint is too strong. ...
BOBBIN WORK INSTRUCTION MANUAL - Multi - Page 12
...small).
c
If the desired results could not be sure to sew trial stitches in the Operation Manual. b Adjust with a screwdriver so it is lower than the top surface of the bobbin ... trial stitches and checking the sewing results, adjust the thread tensions if necessary.
We recommend a setting between 6 and 8 for bobbin work and attaching cords. a Spring plate b
From the wrong...
Brother International Laura Ashley Innov-ís NX2000 Reviews
We have not received any reviews for Brother International yet.