Users Manual - English and Spanish
Page 2
... work area clear: • Never operate the machine with any sudden or careless movements, otherwise you are being used or where oxygen is being sewn may ignite, resulting in injuries. 5 Special care is required when sewing: • Always pay close attention to turn ...the cord. • Plug the machine directly into any other part may damage the machine or result in the instruction manual: • To unplug the machine, switch the machine to the symbol "O" position to the needle. IMPORTANT SAFETY INSTRUCTIONS Please read these safety instructions before attempting to use bent or...
... work area clear: • Never operate the machine with any sudden or careless movements, otherwise you are being used or where oxygen is being sewn may ignite, resulting in injuries. 5 Special care is required when sewing: • Always pay close attention to turn ...the cord. • Plug the machine directly into any other part may damage the machine or result in the instruction manual: • To unplug the machine, switch the machine to the symbol "O" position to the needle. IMPORTANT SAFETY INSTRUCTIONS Please read these safety instructions before attempting to use bent or...
Users Manual - English and Spanish
Page 3
...; Do not push or pull the fabric when sewing, and follow the troubleshooting table in this machine only for household use plugs with this product are subject to change without notice. For additional product information, visit our web site at www.brother.com SAVE THESE INSTRUCTIONS This machine is intended for its intended use outdoors...
...; Do not push or pull the fabric when sewing, and follow the troubleshooting table in this machine only for household use plugs with this product are subject to change without notice. For additional product information, visit our web site at www.brother.com SAVE THESE INSTRUCTIONS This machine is intended for its intended use outdoors...
Users Manual - English and Spanish
Page 4
... narrow hemmer foot 35 Using the blind stitch foot 37 6. CONTENTS IMPORTANT SAFETY INSTRUCTIONS 1 1. SEWING BUTTONHOLES AND BUTTONS 27 Making a buttonhole 27 Adjusting buttonholes 28 Sewing buttons 29 5. APPENDIX 38 MAINTENANCE 38 Restrictions on oiling 38 Precautions on storing the machine 38 Cleaning 38 TROUBLESHOOTING 40 INDEX 43 Straight stitching 23 Zigzag stitching 23...
... narrow hemmer foot 35 Using the blind stitch foot 37 6. CONTENTS IMPORTANT SAFETY INSTRUCTIONS 1 1. SEWING BUTTONHOLES AND BUTTONS 27 Making a buttonhole 27 Adjusting buttonholes 28 Sewing buttons 29 5. APPENDIX 38 MAINTENANCE 38 Restrictions on oiling 38 Precautions on storing the machine 38 Cleaning 38 TROUBLESHOOTING 40 INDEX 43 Straight stitching 23 Zigzag stitching 23...
Users Manual - English and Spanish
Page 13
... ● The needle bar does not move when you slide the bobbin winder shaft to the left and remove the bobbin. Note ● When the sewing machine is started or the handwheel is too short, not pulled taut or held at an angle, injuries may tangle around the bobbin, the... inside of the 7 • Leave 1 cm (1/2 inch) of thread from the hole on the bobbin. 3 1 2 1 1 1 cm (1/2 inch) CAUTION ● Make sure you follow the instructions carefully. If the thread is turned after winding the thread around the bobbin and cause the needle to 10 cm (3 - 4 inches) of thread from the...
... ● The needle bar does not move when you slide the bobbin winder shaft to the left and remove the bobbin. Note ● When the sewing machine is started or the handwheel is too short, not pulled taut or held at an angle, injuries may tangle around the bobbin, the... inside of the 7 • Leave 1 cm (1/2 inch) of thread from the hole on the bobbin. 3 1 2 1 1 1 cm (1/2 inch) CAUTION ● Make sure you follow the instructions carefully. If the thread is turned after winding the thread around the bobbin and cause the needle to 10 cm (3 - 4 inches) of thread from the...
Users Manual - English and Spanish
Page 15
... Make sure that the end of the thread comes out from the cover toward the rear of the machine (as shown in the correct combination. If the upper threading is not correct, the thread may become... 1 5 1 Spool pin 2 Thread guide (back) 3 Thread guide (front) 4 Thread take-up the lower thread before starting 1 sewing. Turn off the machine. 1 Raise the presser foot lever. 2 1 1 Presser foot lever 14 For details on the correct combination of 20 or lower. ●... CAUTION ● When threading the upper thread, carefully follow the instructions. Replace the bobbin cover.
... Make sure that the end of the thread comes out from the cover toward the rear of the machine (as shown in the correct combination. If the upper threading is not correct, the thread may become... 1 5 1 Spool pin 2 Thread guide (back) 3 Thread guide (front) 4 Thread take-up the lower thread before starting 1 sewing. Turn off the machine. 1 Raise the presser foot lever. 2 1 1 Presser foot lever 14 For details on the correct combination of 20 or lower. ●... CAUTION ● When threading the upper thread, carefully follow the instructions. Replace the bobbin cover.
Users Manual - English and Spanish
Page 22
... the presser foot, refer to attach zigzag foot "J", otherwise the needle may break or the machine may bend or break. ● The twin needle should thread each needle separately. SEWING BASICS ■ Attaching the extra spool pin Insert the extra spool pin onto the end of...needle, be sure to "Changing the presser foot" on the machine. 4 Select a stitch. 5 CAUTION ● After selecting a stitch, slowly turn the handwheel toward you (counterclockwise) and check that you threaded the left needle. 1 Follow the same instructions for threading a single needle (see page 14). Install the ...
... the presser foot, refer to attach zigzag foot "J", otherwise the needle may break or the machine may bend or break. ● The twin needle should thread each needle separately. SEWING BASICS ■ Attaching the extra spool pin Insert the extra spool pin onto the end of...needle, be sure to "Changing the presser foot" on the machine. 4 Select a stitch. 5 CAUTION ● After selecting a stitch, slowly turn the handwheel toward you (counterclockwise) and check that you threaded the left needle. 1 Follow the same instructions for threading a single needle (see page 14). Install the ...