Brother International BES-961BC Support and Manuals
Get Help and Manuals for this Brother International item
View All Support Options Below
Free Brother International BES-961BC manuals!
Problems with Brother International BES-961BC?
Ask a Question
Free Brother International BES-961BC manuals!
Problems with Brother International BES-961BC?
Ask a Question
Most Recent Brother International BES-961BC Questions
I Was Told That I Need To Get A New My Mother Board To My Single Head .do You Kn
I was told that I need a mother board . for my single head.Do you know where I can get one.
I was told that I need a mother board . for my single head.Do you know where I can get one.
(Posted by henryarevalo 8 years ago)
Popular Brother International BES-961BC Manual Pages
Thread Tensions - English - Page 2
... screw is not meant to replace the use of the anti-spin spring while setting
the tension. You
may need...could be the problem,
ALWAYS check and adjust bobbin first if necessary. At install and at ...which the tension spring will want to check the tension when using
the corner of a piece of the bobbin. Clean the bobbin case when you see the
needle on the bobbin. Part...
Thread Tensions - English - Page 3
.... How do you adjust them ? At installation and for any tension problems after removing & cleaning them ? For looping problems, turn the knob more turns. At install, after the bobbin has been adjusted as well...more than two to three turns, then there may be checked.
4. What are still having trouble check the thread path and rethread the complete path for ? If the tails are they ...
Thread Tensions - English - Page 5
...set to an exact tension you should see the white streak of bobbin as wide as the two outer streaks of sew out to check your machine. Sew out the bobbin tension test most of your bobbin tension when replacing...letter "H" sewn out at the bottom of thread 1/3, 1/3, 1/3. Other Notes
!" If all the needles are , it , then all just guidelines to setting tensions and correcting tension problems...
Wiper Problems and Solutions - English - Page 1
... part because that the thread is actually cut by the two pieces of the material into the retracted position. Wiper Solenoid Return Spring Plate
Guide
Upper Thread Guide Hook (Wiper)
Slot Thread Presser Base
When addressing problems with the wiper assembly during a trim. Run your upper thread tensions maybe to loose or tail length set...
Wiper Problems and Solutions - English - Page 5
... on the machine.
Color change machine to the solenoid. Manually lower the wiper down on the screw that the bottom part of the return spring mounts to.
First you should see...second. Using a voltmeter set up correctly then either the sensor or solenoid sensor plate needs to be adjusted until the alignment is straight and not bent. Checking upper thread guide hook (wiper) alignment....
Maintenance Schedule - English - Page 9
On 4 head models. Remove the ...7 on machine or by removing the two top screws and loosening the 2 bottom screws.
8. Manually color change box.
5/24/05 9 Remove the color change
screws and loosening the 2 lower... Please Call Toll Fre e 1-877-4BROTHER Email: tsupport@brother.com
Website: http://www.brother-usa.com/industembroidery/tech_down.aspx
6 Month Maintenance
Greasing
Heads continued
5. Remove ...
Tubular to Cap - English - Page 1
... needle #1 using the needle select buttons
.
3) Remove the flat needle plates (A) and replace with the long black thumbscrews (D).
11) Slide the guide bar (F) into the hole to the rear of the arm until the error does not occur.
10) Slide the cap driver unit onto the lower arms of the machine and place the...
Cap to Tubular - English - Page 1
Computer model - It will ask you to confirm canceling the sewing data if using a stand-alone machine ...using the needle select buttons
.
6) Remove the cap needle plates (A) and replace with the flat needle plates.
7) Manually lower all the parts removed on the driver for 5 seconds and power back on Settings, Embroidery Hoop, Tubular (All). Note: You should store all presser feet by ...
Instruction Manual - English - Page 3
...injury that you must make the ground connection".)
BES-961BC • BES-1261BC
1 CAUTION
The instructions which follow this machine and to prevent accidents and ...instruction manual and the indications and symbols that are used on the machine itself are given below and the explanations given in order to ensure safe operation of the caution that you very much for buying a BROTHER...
Instruction Manual - English - Page 4
...installation is complete, otherwise the machine may operate if the start switch is pressed by mistake, which could result in severe injury. Be sure to the machine. Avoid setting...box. If an error occurs in machine ...If the machine develops a problem, contact your skin, ...Brother dealer or a qualified technician.
2
BES-961BC • BES-1261BC
CAUTION
Installation
Machine installation...
Instruction Manual - English - Page 5
...will not be covered by the warranty.
BES-961BC • BES-1261BC
3 Maintenance and inspection
Maintenance and inspection of children. Use only the proper replacement parts as the rotary hook and knife.
Be ..., be absolutely sure to re-install them to observe all safety precautions. Any problems in injury.
If any maintenance and inspection of the electrical system.
Instruction Manual - English - Page 10
... procedures of starting up the machine. BES-1261BC (12 needles)
Explanation for individual model is BES-961BC. Configuration of this manual
This manual consists of the following chapters:
Chapter 1 Preparation of Embroidery Machine This Chapter describes the specifications, installation and preparatory procedures of setting the machine and working environment.
Procedure of Reading This...
Instruction Manual - English - Page 14
...4-1. Replacing and Selecting Needle 38 4-4. Installation 21
3-1. Names of Cotton Stand 30 3-6. Preparation of Embroidery Hoop and Frame 39 4-5. Attachment of Needle Bar Case 24 3-4. Contents
SAFTY INSTRUCTIONS 1 Before Starting Operation 6 Procedure of Reading This Manual 8 Screen Composition 10
Chapter 1 Preparation of Embroidery Data from Floppy Disk 61
12
BES-961BC...
Instruction Manual - English - Page 22
... Accessories
• Holder base 30 x 43 (6) Other embroidery hoops in different sizes
• Sash frame assembly * Other Tajima embroidery hoops that can
be used with BAS-412A and 416A
• Cap frame (6) Cap frame drive assembly (6) Base frame set (12) Set frame base set (1)
• Bobbin winder • Parts for boring
20
BES-961BC • BES-1261BC
Instruction Manual - English - Page 159
... -up movable range.
BES-961BC • BES-1261BC
157
sUpper...set screw of the machine motor pulley loosened? • Is embroidery data normal? sStitches cannot be rotated forcibly by manual...Troubleshooting
Problem sMachine operation abnormal
Check Point
• Is any set screw of the rotary encoder loosened? • Is any set screw of the machine pulley loosened? • Is any set...
Brother International BES-961BC Reviews
We have not received any reviews for Brother International yet.