BenQ MX823ST Short-Throw Network Projector Support and Manuals
Get Help and Manuals for this BenQ item
This item is in your list!
View All Support Options Below
Free BenQ MX823ST Short-Throw Network Projector manuals!
Problems with BenQ MX823ST Short-Throw Network Projector?
Ask a Question
Free BenQ MX823ST Short-Throw Network Projector manuals!
Problems with BenQ MX823ST Short-Throw Network Projector?
Ask a Question
Popular BenQ MX823ST Short-Throw Network Projector Manual Pages
User Manual - Page 3
... on .
Always open the lens shutter (if any) or remove the lens cap (if any objects when the projector is recommended that you connect your projector. This projector is important that you follow the instructions mentioned in this could fail if power cuts or surges of this manual before 5. However, to qualified service personnel.
6. Important safety...
User Manual - Page 7
...Network Control Integrated RJ45 connector for wired network control allowing management of projector status from a computer using a web browser. • Crestron RoomView®, PJ Link and AMX supported The projector supports... depending on the ambient lighting conditions, selected input signal contrast/brightness settings, and is directly proportional to show the best picture quality immediately....
User Manual - Page 10
...-Screen Display
Displays the source selection bar.
(OSD) menu item.
6. Focus ring
10. Lights up red if the projector's temperature becomes too high.
9. problem. Goes back to hide the screen picture.
7. exits and saves menu settings.
Keystone/Arrow keys ( / Up, / Down)
Manually corrects distorted images resulting from an angled projection.
8.
Controls and functions...
User Manual - Page 11
...
19
12
20
13
21
14
22
1.
Left/
Decreases the projector volume.
6.
Introduction 11
ON/ OFF
Toggles the projector between standby
7. Source selection buttons
Emits visible laser pointer light for display. menu.
MODE/ENTER
Selects an available picture setup mode. MHL control buttons
NETWORK)
( Previous, Play/Pause,
Selects an input source for
(COMPUTER...
User Manual - Page 14
... projection screen and the BenQ Projector Ceiling Mount Kit are required for quick setup and portability.
3. Set Rear Table in the SYSTEM SETUP: Basic > Projector Installation menu after you select.
Your room layout or personal preference will dictate which installation location you turn the projector on the table behind the screen. Purchase the BenQ Projector Ceiling Mount Kit from...
User Manual - Page 18
... Video
Better
S-Video
Good
Video
Normal
Connecting audio
The projector has built-in home theater or home cinema applications. The built-in the SYSTEM SETUP: Advanced menu. Usually a key combo like FN +... signal cables have been connected correctly.
18 Connection See "Standby Settings" on both the projector and the video source device as might be muted when the AUDIO-OUT jack is ...
User Manual - Page 23
... is the overview of the OSD menu.
SYSTEM SETUP: Basic
Presentation Timer Language Projector Installation Menu Settings Operation Settings Remote Receiver Panel Key Lock Background Color Splash Screen
Front Table
Front+Rear Off
BenQ BenQ
SYSTEM SETUP: Basic
Presentation Timer Language Projector Installation Menu Settings Operation Settings Remote Receiver Panel Key Lock Background Color Splash...
User Manual - Page 24
... in this manual, and keep the manual in advance or right after the password is entered so that it is available to you should you
desire to set , the OSD menu returns to the Security Settings page.
5. Securing the projector
Using a security cable lock
The projector has to be installed in a safe place.
6.
Confirm the new password by re...
User Manual - Page 25
...six-digit password, or if you did not
record the password in a short time. You have successfully assigned a new password to the SYSTEM SETUP: Advanced> Security Settings > Change Password menu.
2. If you enter the wrong password, the
Password Error
password error message as asterisks on-screen.
displays lasting for details.
Write down the recall code, and contact BenQ Customer Center...
User Manual - Page 26
..., go back to re-activate the password function by the projector depending upon the "aspect ratio" setting, which outputs at the same time.
Though the password function is disabled, you need to the SYSTEM SETUP: Advanced > Security Settings > Change Security Settings menu after opening the OSD menu system. However, it can press MENU/EXIT to search for...
User Manual - Page 32
...to 240 minutes in 5-minute increments. The contrast level of the primary color you select Red and set its range at 0, only the saturation of the desired adjustments. 9. Every adjustment made will be ...presentations. Lower settings produce less saturated colors; Make sure you want the timer to show up on , the timer will reflect to
BLUE
the image immediately. Go to the SYSTEM SETUP: Basic ...
User Manual - Page 39
...Reminder On/Off
On/Off
Language
4. SYSTEM SETUP: Basic
Projector Installation
Front Table/Rear Table/Rear Ceiling/ Front Ceiling
Menu Display Time
5 sec/10 sec/20 sec/30 sec/Always
Menu Settings Menu Position
Center/Top-Left/Top-Right/ ...
Remote Receiver
Front+Rear/Front/Rear
Panel Key Lock
On/Off
Background Color
BenQ/Black/Blue/Purple
Splash Screen
BenQ/Black/Blue
Operation 39
User Manual - Page 40
.../LumenCare
Reset Lamp Timer
Equivalent Lamp
Security Settings
Change Password
Change Security Settings
Power On Lock
Baud Rate
2400/4800/9600/14400/19200/ 38400/57600/115200
5. Current System Status
INFORMATION
• Lamp Mode • Resolution • 3D Format • Color System
• Equivalent Lamp
• Firmware Version
Note that the menu items are accessible...
User Manual - Page 46
...a suitable RS-232 cable and update or download the projector's firmware. Closed Caption Enable Activates the function by selecting On when the selected input signal carries closed captioning mode. Caption Version Selects a preferred closed captions. SYSTEM SETUP: Advanced menu
Function
Description
High Altitude Mode
A mode for details. Lamp Settings
Security Settings
Reset Lamp Timer See...
User Manual - Page 47
...is in standby mode and the COMPUTER-1 jack is able to devices. The projector can be detected by AMX controller. Wired LAN See BenQ Network Projector Operation Guide for how to the projector.
SYSTEM SETUP: Advanced menu
Function
Standby Settings
Network Settings Reset All Settings
Description
Network Selecting On enables the function.
MAC Address Displays the mac address of this...
BenQ MX823ST Short-Throw Network Projector Reviews
Do you have an experience with the BenQ MX823ST Short-Throw Network Projector that you would like to share?
Earn 750 points for your review!
We have not received any reviews for BenQ yet.
Earn 750 points for your review!