Asus P2L-M Support and Manuals
Get Help and Manuals for this Asus item
Popular Asus P2L-M Manual Pages
P2L-M User Manual - Page 4
...8 Introduction to ASUS Smart Series motherboards 9 Parts of Chipset Features Setup 46
4
ASUS P2L-M User's Manual Jumpers 14 Jumper Settings 15 2. System Memory (DIMM 17 DIMM Memory Installation 18 3. Expansion Cards 25 Expansion Card Installation Procedure 25 Assigning IRQs for Expansion Cards 25 Assigning DMA Channels for ISA Cards 26 ISA Cards and Hardware Monitor 26 Accelerated...
P2L-M User Manual - Page 5
... and PCI Setup 52 Details of PNP and PCI Setup 52
Load BIOS Defaults 54 Load Setup Defaults 54 Supervisor Password and User Password 55 IDE HDD Auto Detection 56 Save & Exit Setup 57 Exit Without Saving 57
V. ASUS LAN Card 61 ASUS PCI-L101 Fast Ethernet Card 61 Features 62 Software Driver Support 62 Question and Answer 62
ASUS P2L-M User's Manual
5
P2L-M User Manual - Page 7
... (optional)
ASUS P2L-M User's Manual
7 ASUS L101 Card: Installation of the files • Technical Support Form
(1) User's Manual
Infrared external connector module (optional) ASUS PCI-L101 Wake-on setting up the BIOS software
V. INTRODUCTION
How this product
III. BIOS Software: Instructions on the included support software
VI. I . Support Software: Information on setting up the...
P2L-M User Manual - Page 17
...chips/side + 1 parity chip) and make the proper settings in BIOS Chipset Setup of the DIMM module takes up one Row on the ...ASUS P2L-M User's Manual
17 To utilize the chipset's Error Checking and Correction (ECC) feature, you must have 18 chips or less. BIOS SOFTWARE). IMPORTANT: Memory speed setup is required through "Auto Configuration" in the BIOS Chipset Features Setup (IV. INSTALLATION...
P2L-M User Manual - Page 25
... in use . INSTALLATION
4.
Remove the bracket on a specific device gives you intend to both your expansion card documentation on any hardware and software settings that you configure the card's jumpers manually and then install it in use .
Currently, there are then used and free IRQs. Set any necessary jumpers on the ISA bus.
ASUS P2L-M User's Manual
25 Make...
P2L-M User Manual - Page 34
... Management Setup of ... default setting of the ...ASUS P2L-M User's Manual INSTALLATION
18. The system power LED shows the status of the switch. System Power LED (KEYLOCK, 3 pins) This 3-pin connector connects the system power LED, which lights when the system is a preferred method of rebooting to prolong the life of Enable.
20. INSTALLATION Connectors
III. This function requires ACPI OS support...
P2L-M User Manual - Page 36
...and the path, for example, A:\440XX1 and then press .
36
ASUS P2L-M User's Manual
It is recommended that updates the BIOS by the Flash Memory Writer utility. This file works only ...Support Software
AFLASH.EXE: This is not supported by the ACPI BIOS and therefore, cannot be programmed by uploading a new BIOS file to the programmable flash ROM chip on the upper left-hand corner of the code...
P2L-M User Manual - Page 39
... system stores the Setup utility. All computer motherboards provide a Setup utility program for future reference; If you are installing the motherboard, reconfiguring your system or you receive a Run Setup message, you from calling up the Setup utility. If you are released. You can be slightly different.
ASUS P2L-M User's Manual
39 Press to call up Setup. When you still...
P2L-M User Manual - Page 45
... Password and/or User Password (explained later in this section), the Security Option field determines when the system prompts for shadowing other expansion card ROMs. If you install other expansion cards with installed DRAM of greater than the ROM.
BIOS BIOS Features
ASUS P2L-M User's Manual
45 Relocating to set the two typematic controls listed next.
Setup default setting...
P2L-M User Manual - Page 46
....
Leave on default setting.
SDRAM Banks Close Policy (Arbitration) Leave on default setting.
See section III for the previous screen. MA Wait State (Auto) Leave on default setting. BIOS Chipset Features
NOTE: SETUP Defaults are all 10ns SDRAM, you may set this item to CAS Delay (Auto) Leave on default setting.
46
ASUS P2L-M User's Manual
BIOS SOFTWARE
Chipset Features...
P2L-M User Manual - Page 52
... uses auto-routing to Yes...
52
ASUS P2L-M User's Manual IV. BIOS SOFTWARE
PNP and PCI Setup
This "PNP and PCI Setup" option configures the PCI bus slots. Details of PNP and PCI Setup
PNP OS Installed (No) This field allows you install a legacy ISA card that IRQ. Thus interrupts may be set IRQ10 Used By ISA to determine...
P2L-M User Manual - Page 55
.... A password prompt appears on clearing the CMOS. Taking note that the password is case sensitive, and can be used to 8 alphanumeric characters long, type in the "Security Option" field of entering a new password when the "Enter Password" prompt appears. The system confirms your password and then press . IV. If you to the main screen. ASUS P2L-M User's Manual...
P2L-M User Manual - Page 56
....
When auto-detection is new and empty.
56
ASUS P2L-M User's Manual Skipped entries are ignored and are not entered in the Standard CMOS Setup screen. If you want to accept a set . If you must support the Enhanced IDE features in this case); Some IDE drives can only install two IDE hard disk drives. IV. Do not...
P2L-M User Manual - Page 57
...
Select this option to save the configuration changes, highlight the "Save & Exit Setup" option on the main screen and then press .
ASUS P2L-M User's Manual
57 You will not be detected. Press to reject the presented settings and enter the correct ones manually from the ones used for your hard disk was formatted, the disk will...
P2L-M User Manual - Page 58
SOFTWARE ASUS Support CD
58
ASUS P2L-M User's Manual The LANDesk Client Manager must be installed in order to use the hardware manager features.
• LDCM Administrator Setup: Installs software to see the contents of the ASUS support CD. • Technical Support Form: View the Technical Support Form with Notepad. • LDCM Introduction (MPEG): View a video on the network within the ...
Asus P2L-M Reviews
We have not received any reviews for Asus yet.