Adaptec AHA-1540 - Storage Controller Fast SCSI 10 MBps Support and Manuals
Get Help and Manuals for this Adaptec item
View All Support Options Below
Free Adaptec AHA-1540 manuals!
Problems with Adaptec AHA-1540?
Ask a Question
Free Adaptec AHA-1540 manuals!
Problems with Adaptec AHA-1540?
Ask a Question
Popular Adaptec AHA-1540 Manual Pages
User Manual - Page 1
AHA-1540 User's Manual AT-to-SCSI Host Adapter adaptec, inc.
User Manual - Page 2
... material for possible later reuse should return of each item.
The following section details the installation procedure for the Adaptec AHA-1540 AT to a SCSI target. The installation of the board consists of the various customer configurable items on the AHA-1540.
After opening the shipping container, use the packing slip to verify receipt of damage, have...
User Manual - Page 3
...
0
- XX
1
X- The SCSI parity jumper, pin pair 3 is terminators installed.
AHA-1540
3 - 2
adaptec Pin pair 1 is parity checking enabled.
3.2.3 SCSI Terminators
RN6 and RN7 are ... the AHA-1540 is selected according to the following table. X-
5
X- -
6
- --
7
X = Jumper Installed
J1 4 5 6
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
L pin pair 1
3.2.2 SCSI Parity
Jumper set J1...
User Manual - Page 4
..., controls the terminator power. X
5
X -
6
- -
7
X = Jumper Installed
J1
7 8
0 0 0 0 0 0 0 X 0 0 0
0 0 0 0 0 0 0 X 0 0 0
pin pair 1
AHA-1540
3 - 3
adaptec If another SCSI device is the synchronous negotiation enable jumper. Default is Fl installed with the AHA-1540 supplying the terminator power.
3.2.5 SCSI Synchronous Negotiation
Jumper set by these jumpers according to...
User Manual - Page 5
.... DMA ACK Jumpers
Pin Pair
4 3 - - - DMA REQ Jumpers
- Pin Pair 4 3 21
X X X X
DMA Channel
0 5 6 7
X = Jumper Installed
J6 2
0 0 X 0 0 0 X 0
Pin Pair 1
AHA-1540
3 - 4
adaptec
This jumper set is located near the left corner of pins. Pin pair 1 is the right most set is the right most pair of the small AT bus connector. X X - - - DMA Channel
0 5 6 7
X = Jumper Ins ailed
J7...
User Manual - Page 6
... 0 0 0 0 0 X 0
pin pair 1
Jumper set by the AHA-1540. The interrupt channel used by these jumpers according to the following table. Pin pair 1 is interrupt channel 11.
AT Interrupt Channel
Pin Pair
Interrupt
654 3 21
Channel 9 10 11 12 14 15
X = Jumper Installed
J8 3
0 0 0 X 0 0 0 0 0 X 0 0
I-Pin Pair 1
AHA-1540
3 - 5
adaptec The default is the left most pair of the...
User Manual - Page 7
... Are: 334, 330, 234, 230, 134, 130
AHA-1540
3 - 6
adaptec The default address is coded in jumper block J9. The default address is located just above the left most pair of pins. The port address is 0330H and must match. This jumper set is 330H. Section Three
Installation
3.3.3 AT Port Address
The starting address of the...
User Manual - Page 8
.... Contact your system manufacturer if in the system. AHA-1540
3- 7
adaptec BIOS Address 0C8000H 0 D8000H 0CC000H 0DC000H
J1 0
0 0
0 0 00
Pin Pair 1
X = Jumper Installed
3.3.5 AT BIOS Wait State
Accesses to the left of the SCSI terminator RN7. Default is jumper installed. This jumper set is prevented. This jumper set is ODCOOOH.
X X- -- -
This address must not conflict...
Adaptec AHA-1540 Reviews
We have not received any reviews for Adaptec yet.