Adaptec 2940 - AHA Storage Controller Fast SCSI 10 MBps Support and Manuals
Get Help and Manuals for this Adaptec item
View All Support Options Below
Free Adaptec 2940 manuals!
Problems with Adaptec 2940?
Ask a Question
Free Adaptec 2940 manuals!
Problems with Adaptec 2940?
Ask a Question
Adaptec 2940 Videos
2940 B
Duration: :04
Total Views: 39
Duration: :04
Total Views: 39
m 2940
Duration: 3:28
Total Views: 22
Duration: 3:28
Total Views: 22
PCI Adaptec AHA-2940-UW/B-V5 FSC SCSI-22 50p+68p [9052] - m-ware.de
Duration: :36
Total Views: 91
Duration: :36
Total Views: 91
Popular Adaptec 2940 Manual Pages
Installation Guide - Page 1
Installation Guide
AHA-2940/2940W
PCI-to-Fast SCSI Host Adapter with SCSISelect
R
Downloaded from www.Manualslib.com manuals search engine
Installation Guide - Page 2
... AIC-78xx SCSI Protocol Chip
Adaptec AHA-2940
68-pin 16-bit Internal SCSI
Connector
50-pin 8-bit Internal SCSI Connector
Host Adapter LED
68-pin 16-bit External SCSI Connector
LED Connector Host Adapter BIOS AIC-78xx SCSI Protocol Chip
Adaptec AHA-2940W
1
Downloaded from www.Manualslib.com manuals search engine 1 Introduction
The Adaptec AHA®-2940 and AHA-2940W PCI-toFast SCSI...
Installation Guide - Page 3
... leave the AHA-2940/ 2940W set up your computer.)
PCI slots are shorter than ISA or EISA slots and are three PCI slots. (One of these instructions to install the AHA-2940/ 2940W:
1 Turn OFF power to the computer and peripheral
devices and disconnect the power cords.
2 Remove the cover from www.Manualslib.com manuals search engine
We...
Installation Guide - Page 4
... resolves SCSI ID conflicts automatically at the two extreme ends of the SCSI bus).
3
Downloaded from (see Configuring the Host Adapter on page 8. To disable SCAM support, see Configuring the Host Adapter on the AHA-2940 itself is controlled by a set manually. Note: If you plan to boot your computer from
a SCSI device attached to the...
Installation Guide - Page 5
... SCSI devices, a terminating plug (a resistor pack embedded in a small plug) is installed or removed to control termination.
4
Downloaded from the default setting. On other internal SCSI devices you leave the AHA-2940 set to Low ON/High ON. If you must physically remove or install resistor module(s). This means that termination is enabled for both its internal...
Installation Guide - Page 6
... does not stock these cables, call Adaptec directly at the number for ordering Adaptec software and cables listed on page 12. 4 Installing SCSI Devices
You can connect up to a total of seven internal and external 8-bit SCSI devices to the AHA-2940, and up to two internal SCSI devices (the AHA-2940 kit includes a 50-pin internal SCSI cable...
Installation Guide - Page 7
... host adapter's external SCSI connector.
6
Downloaded from your com- config- For instructions, see the device's documentation as well ... internal SCSI devices, make sure you install.
1 Prepare each SCSI device for installation; Make sure the colored stripe on...5 Connect a DC power cable (from www.Manualslib.com manuals search engine Connecting Internal SCSI Devices
If you are connecting ...
Installation Guide - Page 8
... on the following section, Configuring the Host Adapter.
SCSISelect Default Settings
The AHA-2940/2940W has the default settings shown in the table on your SCSI hard disk drives.
Your host adapter is ready for operation and you can proceed to Installing Device Drivers on page 10.
7
Downloaded from the LED connector on the motherboard and connect it...
Installation Guide - Page 9
... More Than 2 Drives4
Enabled
BIOS Support for Bootable CD-ROM4
Enabled
BIOS Support for Int 13 Extensions4
Enabled
1 Applies to AHA-2940 only 2 Applies to AHA-2940W only 3 Setting is valid only if Multiple LUN Support is enabled 4 Settings are valid only if host adapter BIOS is enabled.
8
Downloaded from www.Manualslib.com manuals search engine If you would like...
Installation Guide - Page 10
... press Enter. Starting the SCSISelect Utility
You can start the SCSISelect utility by pressing Esc.
s Format Disk-This utility allows you exit).
Exiting SCSISelect To exit SCSISelect, press Esc until a message prompts you to exit (if you changed any key to exit, then press any AHA-2940/2940W settings, you select a specific ID and device, a small menu...
Installation Guide - Page 11
... connected? s Adaptec 7800 Family Manager Set-allows you to install software drivers for your AHA-2940/2940W;
s Does the host adapter and all devices on page 12.
9 Troubleshooting Checklist
If you have unique SCSI IDs?
10
Downloaded from www.Manualslib.com manuals search engine
You can press Esc at its optimum level. Is pin 1 oriented correctly? If the utility finds bad...
Installation Guide - Page 12
...'s
CMOS setup is set with jumpers or switches on the drive.
3 If this does not solve the problem, back up all devices on partitioning the disk after formatting.
11
Downloaded from www.Manualslib.com manuals search engine Computer Will Not Boot from a SCSI Disk Drive
If both SCSI and non-SCSI disk drives are installed, then...
Installation Guide - Page 13
... from www.Manualslib.com manuals search engine 10 Adaptec Customer Support
If you have questions about installing or using your questions here. s To request additional documentation for Adaptec products, call 800-934-2766 or 510-732-3829, M-F: 6:00 a.m. s The Adaptec Electronic Bulletin Board Service (BBS) provides information on software upgrades, product literature, answers to...
Installation Guide - Page 14
... some jurisdictions. Each host adapter is subject to operate such equipment. Adaptec, the Adaptec logo, AHA, EZ-SCSI, and SCSISelect are designed to change without notice.
13
Downloaded from that to
which can radiate radio frequency energy, and if not installed and used in residential installations. These limits are trademarks of the FCC rules.
A RQ 7/95...
Adaptec 2940 Reviews
We have not received any reviews for Adaptec yet.