Acer XV271Z Support and Manuals
Popular Acer XV271Z Manual Pages
User Manual - Page 2
... to the contents hereof and specifically disclaims the implied warranties of purchase information in any form or by photocopy, recording or otherwise, without obligation to notify any means, electronically, mechanically, by any person of Acer Incorporated. Acer Incorporated. No part of this publication may be incorporated in this manual or supplementary documents and...
User Manual - Page 5
...the product exhibits a distinct change in performance, indicating a need to replace the power cord set . Contact your electrician for service • the product does not operate normally after following requirements: detachable..., make sure that the new power cord meets the following the operating instructions English
• If an extension cord is not properly grounded may result...
User Manual - Page 15
The cord set consisting of H05VV-F cord and plug rated 10 A/250 V. State ON Power Saving Mode
LED Light Blue Amber
The power saving states will be installed. English
Connecting the adapter and AC Power cord
• Check first to the Adapter, and plug the other end into "Power Saving" mode by the...
User Manual - Page 16
... and corresponding timing. The monitor supports the DDC2B standard.
19-pin color display signal cable*
PIN No. Description 1 ML_Lane 0+... 18 GND 10 ML_Lane 3+ 12 ML_Lane 314 CONFIG2 English
Display Data Channel (DDC)
To make installation easier, so long as your system supports the DDC protocol, the monitor is a communication protocol through which the monitor automatically informs the host...
User Manual - Page 17
... by the panel specification.This function can be use the system control panel to a lower refresh rate through the on-screen display settings. If you experience instability, try reducing the overclock to set the maximum refresh rate. However, overclocking may result in system instability. Important: This device is designed to...
User Manual - Page 18
...cable into a nearby electrical outlet. Please check user manual for audio output model. English
HDMI 1(2.0)
HDMI 2(2.0)
DP
Note: Audio output is only for more instruction.
Then tighten the thumbscrews on the computer. Turn off... of your computer and your computer's power cord. 2. Installation
1. Plug the power cords of the graphics card on the signal cable connector. 3.
User Manual - Page 19
.... b. a.
When the Function Menu is active, press this key to view the basic
information for your monitor and current input or reset the custom color settings to enter next function in four directions. Grey indicates inoperable. Press to view Main page.Press again to view Main page. a. b.
a. English
User Controls
1
2 3 4
5
External...
User Manual - Page 20
... and store. Brightness
80
Adjust
OK Hot Key1 (Modes,Brightness,Volume,Gamma,Contr ast,Blue Light,Over Drive,VRB)
2. Input selection
4.
Actual product specifications may vary. For advanced settings, please refer to following content is for general reference only. Hot Key2 (Modes,Brightness,Volume,Gamma,Contr ast,Blue Light,Over Drive,VRB...
User Manual - Page 21
... Source
On
Move
Enter
Exit
The Function page
Open the Function page to adjust the functions, settings which you are done, toggle the joystick to the left or right to open the OSD...joystick to exit current page and store. Picture
Picture Color Audio Gaming OSD System
Save Settings to 100 Note: Sets the degree of difference between light and dark shades.
6. Move
Mode - Selecting the...
User Manual - Page 23
...X
Main Source DP
Resolution 1920x1080
H/V Frequency H:66KHz V:60Hz
Mode HDR
Information
S/N: MN53035032682018TPV888
Reset ALL Settings Exit
Move
Enter
HDR = (Auto or HDR-400)
• HDR function and Effect:
Move
...Off (Default)
Behavior Auto checked input source status Auto checked input source status
No support HDR effect
Note:
1. HDR = (Auto or HDR-400), The source signal content...
User Manual - Page 26
... System
Mode - Move
Enter
1. Stardard Volume Mute
70 Off
X
Save Settings to open the OSD. 2.
Press the MENU key to ... AMD FreeSync Premium: To control support AMD FreeSync Premium or not, default is "OFF", then the user can set to either one of the three settings including: (a) Extreme (b) Normal (c) Off. Volume: Adjust the volume 5.
User Manual - Page 27
... "Off". 3. VRB function does not affect the (Logo, Aim Point, Message and Input Icon) brightness. 5. VRB setting "On", when detection of Input Timing English
6.
VRB set VRB is "Off". 4. VRB: To choose whether to adjustment (Brightness, Blue Light, ACM), will auto set "On", when to support dynamic picture more clean control, default is not...
User Manual - Page 28
The transparency can support auto search for signal source in order Note: Surround application must set Auto Source is "On", which screen aspect you wish to adjust and press...OFF), 20%, 40%, 60%, or 80%.
7. OSD timeout: Adjust the delay before turning off Note: OSD Locked: • Set the OSD Lock to "On" by the OSD option and press "Enter" to Blue Light.
Toggle the joystick to the up...
User Manual - Page 29
... level.
10. User
Picture Color Audio Gaming OSD System
Game Mode Action Game Mode Racing Game Mode Sports
Save Settings to ..." Quick start mode: Select Off or On. When Over Clock = "On", It support max resolution to open the OSD.
2. Press the MENU key to 1920x1080 280Hz. HDMI Black level: Select to...
User Manual - Page 30
... sending your LCD monitor for servicing, please check the troubleshooting list below to their default setting. HDMI /DP Mode (Optional)
Problem No picture visible
LED status Blue
Off
Remedy
Using the OSD menu, adjust brightness and contrast to maximum or reset to see if you can self-diagnose the problem. Check the power switch. Check...
Acer XV271Z Reviews
Do you have an experience with the Acer XV271Z that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Acer yet.
Earn 750 points for your review!