Acer B227QA Support and Manuals
Get Help and Manuals for this Acer Computers item
Popular Acer B227QA Manual Pages
User Manual - Page 2
...model number are registered trademarks of merchantability or fitness for identification purposes only and belong to the contents hereof and specifically disclaims the implied warranties of Acer Incorporated. No part...transmitted, in this manual or supplementary documents and publications. All correspondence concerning your computer. Acer LCD Monitor User's Guide
Model number Serial number ...
User Manual - Page 3
... the image or turning off the power switch for a few hours. • Acer monitor is purposed for video and visual display of information obtained from the LCD monitor:
• Make sure the monitor is displayed for your monitor
Please carefully follow these instructions carefully. Connecting/disconnecting the device
Observe the following are turned off the power...
User Manual - Page 5
...Note: The grounding pin also provides good protection from the wall outlet and refer servicing to replace the power cord set . v
ampere rating of the equipment plugged into a non-grounded power outlet...electrical devices that the new power cord meets the following the operating
instructions If you to qualified service personnel. Unplug this product yourself, as opening or removing covers may...
User Manual - Page 6
...instructions, since improper adjustment of used equipment, as grain, dust or metal powders.
IT Equipment Recycling Information
Acer is strongly committed to this website: http://www.acer-group.com/public/Sustainability/
Visit www. We at service... them out of the reach of our other controls may contain small parts.
vi
Note: Adjust only those controls that are in progress. Potentially...
User Manual - Page 15
...set should have the appropriate safety approvals for damage resulting from giving shock or scratch to the screen, as screen is fragile. In order to prevent damage to the monitor, do not lift the monitor by its base. CLEANING YOUR MONITOR...DISPLAY SCREEN OR CASE. Acer will not be liable for the country in which the equipment will be installed. CONNECTING THE POWER CORD
...
User Manual - Page 16
... Data Channel) is able to ON state is around 3 seconds.
The monitor supports DDC2B standard.
EN-6 DDC
To make your installation easier, the monitor is a communication protocol through which the monitor automatically informs the host system about its capabilities, for example, supported resolutions and corresponding timing. The recovery time from the display controller, as...
User Manual - Page 19
... Hz 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz 75 Hz
Remark For DP/HDMI only
Note: The DisplayPort of this monitor is purposely supporting the Adaptive-Sync support technology and targeting AMD graphic solutions. For other GPUs, please contact the graphic card manufactures whether they can...
User Manual - Page 20
...Optional) 3. Insert the monitor power cable into a nearby electrical outlet. 5. EN-10 Connect the DP cable to the computer. 1-2 Connect HDMI Cable (Only HDMI-input model) a. Select Power-off ...cable to the computer. 2. INSTALLATION
To install the monitor to your monitor into the power port at the back of the monitor. 4. Connect the HDMI cable to other settings than the center position may ...
User Manual - Page 22
...OSD (on-screen display) can be achieved. Press the MENU button to your LCD Monitor. Adjusting the OSD settings
Note: The following page: Main Page The default function for buttons 1 and 2...the picture quality, OSD position and general settings. Input 4. Actual product specifications may vary. You can use the Hot Key Assignment function to set these buttons to open the OSD. ...
User Manual - Page 25
.... The higher the level, the higher the boost. 8. Note: Sets the degree of the display- blacks will be less black. V. ACM: Turn ACM On or Off. ... best protection, select a lower value. 7. Clock (only Analog input model): Adjust the clock from 0 to 100. 11. Position (only Analog input model): Adjust the horizontal position from 0 to 100.
It can simulate high...
User Manual - Page 28
.../OK button, select Performance from the OSD. Over Drive: Select Off, Normal, or Extreme. 5. Adaptive-Sync is available for AMD
supported graphic cards only. 6. Press the MENU button to select the setting. 4. Use the Navi/OK button to open the OSD. 2. Refresh rate num: Display the panel's current refresh rate on the...
User Manual - Page 32
EN-22 TROUBLESHOOTING
Before sending your LCD monitor for servicing, please check the troubleshooting list below to see if you can self-diagnose the problem.
(VGA Mode)
Problems No Picture
Abnormal Picture Abnormal Sound (Only AudioInput model) (Optional)
Current Status LED ON LED OFF LED displays amber color Unstable Picture
Display is missing, center shift, or too small...
User Manual - Page 33
...cord is properly connected to their default settings.
Check the power switch. (HDMI/DP Mode)
Problems No Picture Abnormal Sound (Only Audio-Input model) (Optional)
Current Status
Remedy
LED ...ON
Using OSD, adjust brightness and contrast to maximum or reset to the monitor.
...
User Manual - Page 35
... St., Suite 1500 San Jose, CA 95110 U. Contact Person:
Acer Representative
Phone No.:
254-298-4000
Fax No.:
254-298-4147... any interference received, including interference that may not cause harmful interference, and (2) this declaration:
Product:
LCD Monitor
Model Number:
B227Q
SKU Number:
B227Q xxxxxx ("x" = 0~9, a ~ z, or A ~ Z)
Name of Responsible Party: Address of the FCC Rules...
User Manual - Page 36
... risks of inactivity. • Wake the monitor when it is ENERGY STAR? The more...set by reducing energy costs and helps protect the environment without sacrificing features or performance. Environmental Protection Agency. Acer...Acer's ENERGY STAR qualified products save you money by the U.S. Acer is proud to offer products and services worldwide that are registered U.S. marks
EN-26 Acer...
Acer B227QA Reviews
We have not received any reviews for Acer yet.