Troy-Bilt TB625 Support Question
Troy-Bilt TB625 Support Question
Find answers below for this question about Troy-Bilt TB625.Need a Troy-Bilt TB625 manual? We have 1 online manual for this item!
Current Answers
Related Troy-Bilt TB625 Manual Pages
Operation Manual - Page 1
... Customer Support Department at the time of printing. Copyright© 2013 MTD SOUTHWEST INC, All Rights Reserved.
01/13 Operator's Manual
Electric Start Capable 4-Cycle Trimmer
TB625 EC
TABLE OF CONTENTS Service 1 Safety 2 Know Your Unit 5 Specifications 5 Assembly 6 Oil and Fuel 8 Starting and Stopping 10 Operation 12 Maintenance 13 Cleaning and Storage...
Operation Manual - Page 2
... Signals a MODERATE hazard.
Replace damaged parts. Never remove the fuel tank cap or add fuel when the engine is hot. Move the unit at a minimum. Remove rocks, broken glass, nails, wire, string and... maintained in a well ventilated outdoor area.
• Be aware of risk of injury to the head, hands and feet.
• Carefully inspect the area before filling the tank. Failure to obey ...
Operation Manual - Page 3
... unit immediately. Wear a face mask or dust mask if the operation is idling. The cutting head remains stationary when the engine is dusty.
• Wear heavy long pants, boots, gloves and... this tool for this unit.
Do not touch or try to prevent unauthorized use . Carefully remove vegetation and other users. Make sure all moving parts.
• To reduce fire hazard, ...
Operation Manual - Page 4
You may appear on trimmer attachment
shield. Failure to do not touch the line cutting blade.
4 Keep away from the rotating rotor.
• KEEP BYSTANDERS AWAY
WARNING: Keep all warnings ...
Operation Manual - Page 5
...Cap
Handle Shaft Housing
Air Filter Cover
Throttle Control
Choke Lever
Cutting Head
Coupler
Cutting Head Shield
Oil Fill Plug
Line Cutting Blade
SPECIFICATIONS*
Engine Type Air-... cu. Other optional accessories may be used with cutting head, cutting head shield and handle 13 - 14 lbs. (5.9 - 6.4 kg) Trimmer Mechanism Bump Head Trimming Line Diameter 0.095 inches (2.41 mm) Cutting Path...
Operation Manual - Page 6
... only the instructions that provides the best grip. Remove the wing nut and washer from the end of 6 inches (15.24 cm) from the cutting head shield.
2. Put the washer onto the square bolt...the handle to the location that apply to the location that provides the best grip.
Cutting Head Shield
Slot Fig. 1
INSTALLING AND ADJUSTING THE HANDLE
Installing the Handle
1. Adjusting the Handle
...
Operation Manual - Page 7
...the release button with the attachment. CAUTION: Before operating the unit, make installing or removing the attachment easier, place the unit on the ground or on a work bench.... button (Fig. 5). 3. Follow all safety information contained within. For decorative edging with a string trimmer attachment, lock the release button into
the primary hole only. CAUTION: The release button should be ...
Operation Manual - Page 8
...the oil level before starting the unit.
Unscrew the oil fill plug (Fig. 8). 5. cycle engine. Remove the paper seal. DO NOT mix oil with a 2.03 fluid oz. (60 ml) bottle of ...be added before each use dirty oil. DO NOT use . NOTE: This unit comes with gasoline. 6. Remove the cap from the oil bottle.
Reinstall the oil fill plug. NOTE: This unit was shipped without oil...
Operation Manual - Page 9
...to inhibit corrosion and minimize gum deposits. It has been proven that may explode. WARNING: Remove the fuel cap slowly to the unit's fuel tank. WARNING: Add fuel in place. Avoid...the tank. Never operate the unit without the fuel cap securely in a clean, well ventilated outdoor
area. Remove the fuel cap. 3. Place the fuel container spout into the fill hole on the container. As little...
Operation Manual - Page 11
..., move the choke lever to squeeze the throttle control.
Refer to restart the engine. Slowly press and release the primer bulb 10 times (Fig. 10).
4.
Remove the electric start accessory (items sold separately). IF... If the engine speed fluctuates in intervals no longer than 2 seconds each until
the engine comes to...
Operation Manual - Page 12
... 14
Fig. 15
Bump Knob
Fig. 16 CAUTION: Do not remove or alter the line cutting blade
assembly.
TIPS FOR BEST TRIMMING RESULTS • Keep the cutting head parallel to the ground. • Cut from :
• ... stopping the engine. This may stall the engine. OPERATION
HOLDING THE TRIMMER WARNING: Always wear eye, hearing, hand, foot and body protection to reduce the risk of trimming line...
Operation Manual - Page 13
...of new trimming line. 3. Pull the line until a few inches protrude from the cutting head. NOTE: Some maintenance procedures may not release properly if the line is too long.
Refer... the cutting head until the ends are unsure about 5 inches (12.7 cm) protrude from starting accidentally. If necessary, remove any seasonal tune-up.
Always allow the unit to Removing Old Trimming ...
Operation Manual - Page 14
... the tabs securely snap into the oil level window; Add oil to prevent debris
from the cutting head. 1. Tab Hole
Fig. 19
Fig. 20
Oil Fill Plug Oil Fill Hole
Maximum Oil Level
Fig...on the outer
spool (Fig. 19). Unscrew the oil fill plug. 3. Reinstall the oil fill plug. Remove any old trimming line and/or obstructions. 4. CHECKING THE OIL LEVEL
WARNING: OVERFILLING THE CRANKCASE MAY
CAUSE ...
Operation Manual - Page 15
... improper air filter maintenance is still warm. Lightly coat the air filter with clean SAE 30 oil. 5. Insert the cover screw into
a container (Fig. 22).
Remove the air filter from the air filter housing (Fig. 24).
2. Wipe up any oil that may have spilled. 5. Cleaning the Air Filter
1. Swing the air...
Operation Manual - Page 16
..., and adjusting the idle speed should make carburetor adjustments. Remove the spark plug from the spark plug.
2. Grit in the cylinder head.
Clean around the spark plug. WARNING: Do not sand... (Fig. 25). Tighten the spark plug with a 5/8-inch socket, turning it from the cylinder head with replacement part #753-05784, a Champion RDZ4H or an equivalent spark plug.
4.
If the ...
Operation Manual - Page 17
... to distribute the oil. Preparing the Unit for more than 30 days. NOTE: Do not use strong detergents. Long-term Storage
1. Reinstall the spark plug.
4. Remove the spark plug and drain all fuel has been drained from the cylinder. 2.
Repair or replace damaged parts and tighten loose screws, nuts or bolts...
Operation Manual - Page 18
... replace the air filter Replace the spark plug
Stop the engine and clean the cutting head Refill the cutting head with new line Rewind the line Clean the inner reel and outer spool Open the cutting head and remove the welded section Rewind the line Stop the unit, push the bump knob and pull...
Operation Manual - Page 20
... above limitation may not apply to you .) In no event shall recovery of any Troy-Bilt Product without limitation, expenses incurred for substitute or replacement lawn care services, for transportation or for related expenses, or for whom it was purchased as set forth in Canada. Troy-Bilt reserves the right to...
Similar Questions
Changing Trimmer Head On Troy-bilt Tb6044 Xp
I have a TB6044 XP and want to replace the trimmer head with a Pivotrim hybrid. But cannot remove th...
I have a TB6044 XP and want to replace the trimmer head with a Pivotrim hybrid. But cannot remove th...
(Posted by GCP1 8 years ago)
How Do I Remove The Cutting Head Of The Tb625 Ec Trimmer
head removal instructions.
head removal instructions.
(Posted by Anonymous-150877 8 years ago)
Replace Trimmer Head
I want to replace the trimmer head with an ugly head. The nuts provided in the ugly head package do ...
I want to replace the trimmer head with an ugly head. The nuts provided in the ugly head package do ...
(Posted by ipferrara 10 years ago)