Singer 14J250 Stylist II Serger Support Question
Singer 14J250 Stylist II Serger Support Question
Find answers below for this question about Singer 14J250 Stylist II Serger.Need a Singer 14J250 Stylist II Serger manual? We have 1 online manual for this item!
Question posted by vickrisblanco on February 21st, 2013
Thread Guide Pole Is Stuck
I can't pull the thread guide pole to the highest position. I just received it today and it will not go up all the way.
Current Answers
Related Singer 14J250 Stylist II Serger Manual Pages
Instruction Manual - Page 2
... not pull or push fabric while stitching. It may deflect the needle causing it has been dropped or damaged, or dropped into water. " Read all moving parts. "Never operate the sewing machine with EEC Directive 2004/108/EC covering the electromagnetic compatibility. "Use this sewing machine only for its affiliates.
"Switch the sewing machine off („0") position, then...
Instruction Manual - Page 7
...feed control dial
25. Stitch length dial
26. Moving cutter
31. Overedge cutting width dial
3
9. Working table
10. Release lever
21. Upper looper
33. Sewing light
4. Plug connector socket
28. KNOWING YOUR SEWING MACHINE
IDENTIFICATION CHART 1
1. Thread guide pole
4
11. Front cover
30. Lower looper
34. Cutting width gauge
9
20. Power/light switch
29. Cord...
Instruction Manual - Page 9
...
11. Wrench
12. Blind hem foot 20. Screw driver (small)
6. Oiler
10. Spool disc
1
15. Vinyl dust cover
ADDITIONAL ACCESSORIES
19. Spool cap (on machine)
17. Two-thread converter
2. Package of needles
8. Screw driver (large)
9. Spool holder
16. Tape measure (option)
7. Brush
5. Tweezers 14. Gathering foot 21. Elasticator foot
6
7
8
9
3
4
5
10
11
12...
Instruction Manual - Page 11
... power/light switch is turned on. This same switch controls both machine power and sewing light. OPENING WORKING TABLE To open working table, pull the release lever toward you to open front cover, pull it to power supply outlet.
3. Illustration
* I : Plug connector socket * II : Power/light switch * III : Release lever * IV: Working table * V : Front cover...
Instruction Manual - Page 13
... the spool stand and draw thread through thread guides on the pins. Place spool discs on the pole from rear to front. For storage, use the thread guides on the pole to hold thread spools on the spool stand by pushing down on the pole to lower it click. PREPARATION FOR THREADING THREAD GUIDE POLE
Pull up thread guide pole to the highest point until you hear it...
Instruction Manual - Page 19
... No. 80-60 Polyester No. 60 - 50 Cotton No. 60 Polyester No. 60 - 50 Bulk Nylon
NEEDLE
90 (14) for general
sewing 75 (11) for light weight fabrics
* Synthetic threads are recommended for your project.
18
TABLEAU DES FILS ET MATIERES
Utiliser SINGER Cat. No. 2022. Le fil polyester, par exemple, est...
Instruction Manual - Page 21
... when the presser foot is up. Pull the lower thread through the thread guide as illustrated. 2. Holding the thread with your left hand, pull down with right hand firmly. 3. Open the front cover and the working table.
STARTING TO SEW
THREADING YOUR MACHINE
Wrong threading may cause skipped stitches, breaking threads, or other problems. Try to its highest point by the
arrow...
Instruction Manual - Page 23
Draw the thread through the thread guide as illustrated.
(When threading according to the instructions, upper looper thread passes the thread guide (A) automatically after turning the hand wheel.) 4. Feed the thread through the thread guide as illustrated. 2. Holding the thread with your left hand, pull down with right hand firmly. 3. Pull an excess thread length of about 4" (10 cm) ...
Instruction Manual - Page 25
... the thread with your left hand, pull
down with right hand firmly. 3. Draw the needle threads through needle eye and pull the threads towards the
back passing along the right side of presser foot, leaving an extra length of about 4" (10 cm).
24 Draw the thread through the thread guide as illustrated. 4. THREADING NEEDLES
1. Feed the thread through the thread guides as...
Instruction Manual - Page 27
... clamp.
7. Raise the needle bar to highest position, and pull the thread leaving about 4" (10 cm) clear.
2. Move the needle threader backwards slightly. For right needle / Pour aiguille droite / Para la aguja derecha For left needle / Pour aiguille gauche / Para la aguja izquierda
26
7 7 Feed the thread through the thread guide of the machine. Raise the presser foot.
Instruction Manual - Page 31
...thread tensions by test sewing on most fabrics except bulky materials.) Guide the fabric gently as machine automatically feeds the material.
3. Rotate the hand wheel toward
you plan to sew and test sew in test fabric under the presser foot by pushing thread... pulling all the threads to see if the lock stitches are produced off the fabric. Start the machine at a low speed, gently pulling ...
Instruction Manual - Page 33
...; 4 →
← 4 → ← 4 → ← 4 →
Stitch length control
2.5 - 3.5
2.5 - 3.5
Ref. Try test-sewing with wooly nylon thread, set the thread tension control dial at ← 2 →. SETTING CHART
Number of scrap you sew light or heavy weight fabric. 3.
No.
1
2
3
3
3
2
4→ ←5→
4
4 - 6
6
← 6 →
Left
Right
Right...
Instruction Manual - Page 39
... Pull the stitch finger from the needle plate using a screwdriver.
Please use the recommended threads... below for use on light weight fabrics such as illustrated or in the needle plate. The picot stitch can be used when sewing...
Rolled edge with Three Threads with Two Threads
Nylon No. 100
Bulk nylon (less stretchable)
Illustration
* I : Stitch finger (A) * II : Cross section showing...
Instruction Manual - Page 45
... fabric using three threads (right needle only) and setting the width dial at 4 - 5 (Fig. 3).
Decrease the cutting width by turning it towards 5 if fabric edge curls while sewing. (Fig. 1)
Increase the cutting width by simply turning the Overedge cutting width dial to get proper stitching. (Fig. 4)
Illustration
* I : Stitch length dial * II : Overedge cutting...
Instruction Manual - Page 49
...II : Increase *III : Decrease *IV : Tighten * V : Loosen *VI : Cutter release mechanism screw.
48
The lever can be sewn on this machine. If adjustment is necessary, turn the overedge cutting width dial to decrease pressure.
When sewing... fabric can be made between 0.7 (negative effect) and 2 (positive effect).
SETTING DIFFERENTIAL FEED
Set by simply moving the differential feed ...
Instruction Manual - Page 53
... the left needle thread guide (3). Increase speed as follows:
1. See Fig. 1.
2. Be sure it under the presser foot as a crochet cotton, gimp, wool, knitting yarn, or shirring elastic at intervals and pull out looper thread(s).
Place a "filler" cord, such as usual.
Pass it is feeding correctly. Follow directions as needed. Your machine is equipped with...
Instruction Manual - Page 55
... overlocking, which is fully described in this instruction book, your machine can be achieved. using buttonhole twist or embroidery thread on the lower looper. A
Unfold the fabric, pull the ends of using three threads (flat seam) Fold fabric along the line to the normal position by pushing in and turning it
away from you use...
Instruction Manual - Page 61
... serger and foot control clean. Use dry rags to avoid electrical shock.
Use the brush to the points indicated by arrows.
CLEANING AND OILING
To keep the machine running smoothly, keep it clean and lubricated at all times.
Apply a few drops of oil to remove dust and lint. ALWAYS USE A GOOD QUALITY SEWING MACHINE...
Instruction Manual - Page 63
... blunt needle Incorrect setting of Needle
Loose presser foot Bent or blunt needle Thread tension (s) too tight Incorrect setting of Needle Thread Spool tangled Thread guide pole not extended
CORRECTION
Reset thread tension (s) Insert correct size needle for thread and fabric Re-thread machine Do not pull fabric; guide it at 1 or at less than 1
Set it gently Re-attach presser...
Instruction Manual - Page 65
... left needle just catching the fold of pearls extending behind foot. • Take one stitch with the hand wheel to secure the pearls. • Sew pearls on the edge of fabric along fabric guide on Pearl foot. • Sew pearls on with Pearl foot. • Insert Stitch finger B • Lower cutter to it 's highest position. •...
Similar Questions
Serger Thread Pole Flops All Over, Raises Up But Wiggles All Over, Whats Wrong?
(Posted by jm118114 9 years ago)
Beeping From Singer Sewing Machine Stylist Ii 5625
My sewing machine will beep and stop sewing after three inches of sewing. I have taken it to be repa...
My sewing machine will beep and stop sewing after three inches of sewing. I have taken it to be repa...
(Posted by arusheria 9 years ago)
Do It Yourself Repair Manual
My sister gave me her serger. I would like to try to fix it myself. How can I find the repair manual...
My sister gave me her serger. I would like to try to fix it myself. How can I find the repair manual...
(Posted by SandyWagner 10 years ago)
I Am Trying To Down Load To My Reader But I Have Not Been Able To Do So.
Can I have a manual for the singer stylist II serger 14J250 mail to my home.
Can I have a manual for the singer stylist II serger 14J250 mail to my home.
(Posted by pcriss41 10 years ago)