Ryobi TS1342L Support Question
Ryobi TS1342L Support Question
Find answers below for this question about Ryobi TS1342L.Need a Ryobi TS1342L manual? We have 4 online manuals for this item!
Question posted by golfesxu on March 22nd, 2014
How Do I Replace The Spring On My Ts1342l 10 Lower Blade Guard
The person who posted this question about this Ryobi product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Ryobi TS1342L Manual Pages
English Manual - Page 1
... for your purchase. WARNING: To reduce the risk of operation, and operator safety. Thank you years of rugged, trouble-free performance. OPERATOR'S MANUAL
10 in. Compound Miter Saw
TS1342L -
When properly cared for, it will give you for dependability, ease of injury, the user must read and understand the operator's manual before...
English Manual - Page 2
...stated in any case, within ninety (90) days or less.
To receive a replacement power tool or requested warranty service, you must present proof of purchase. We will repair any...warranty covers all defects in workmanship or materials in the design of Terms...9 Features...10-12 Tools Needed...12 Loose Parts...13 Assembly...13-20 Operation...21-...
English Manual - Page 3
... switch is damaged should be properly repaired or replaced by preventing body contact with sufficient set. Consult the operator's manual for lubricating and changing accessories.
DISCONNECT TOOLS. Before further use of the tool, a guard or other conditions that can get caught and draw you into a blade, cutter, or sanding spindle against the direction or...
English Manual - Page 4
... the saw with the blade touching the workpiece. Repair or replace a damaged or worn cord immediately. Do not operate tool when you are tired. Do not rush.
DO NOT USE TOOL IF SWITCH DOES NOT ...on the saw or workpiece before starting cut.
NEVER cut more than one blade is 10 in a polarized outlet only one piece at approximately hip height.
KEEP HANDS AWAY ...
English Manual - Page 5
...tool and wait for saw blade to stop before
moving workpiece or changing settings.
THIS TOOL should any electrical component fail to perform properly, shut off the power switch, remove the miter saw plug from the power source and have damaged, missing, or failed parts replaced...without guards in place. g) Disconnect power (or unplug tool as applicable)
before any use of the saw blade....
English Manual - Page 8
...replace immediately. ELECTRICAL CONNECTION
This tool has a precision-built electric motor. Do not operate this tool on lumber, tools or other obstructions while you return the tool...a power tool at a ... a tool with a power tool. Use... factory replacement parts... tools do...tool's internal insulation. It should be connected to handle the current the tool...**Ampere rating (on tool data plate)
0-2.0 ...
English Manual - Page 10
FEATURES
PRODUCT SPECIFICATIONS
Blade Arbor 5/8 in . No Load Speed 5,500 r/min. (RPM) Input 120 V, AC only, ... at 45°/Bevel 45°: Maximum nominal lumber sizes 2 x 4
blade wrench
Upper Blade Guard
"D" Handle
DUST BAG Bevel
Lock Knob
Bevel Scale MITER Fence
Miter Table
BASE
Switch Trigger
Lower blade guard
throat plate
"NO HANDS ZONE" LABEL
"NO HANDS ZONE" BOUNDARY LINE
Miter...
English Manual - Page 11
...recessed areas for carrying the saw 's base. BLADE
A 10 in the saw . One end of servicing.
10 in this product requires an understanding of the ...tool and in . ELECTRIC BRAKE
An electric brake has been provided to handle tough cutting jobs. MITER FENCE
The miter fence on each side of the project you are for making all ball bearings, and has externally accessible brushes for the blade...
English Manual - Page 12
...
The following tools (not included) are needed for making adjustments or installing the blade:
Combination Wrench (2) 10 mm ,12 mm
hex key 5 mm
FRAMING SQUARE
COMBINATION SQUARE Fig. 5
12
The spindle lock button locks the spindle stopping the blade from each side of the blade. SPINDLE LOCK BUTTON
See Figure 3. SELF-RETRACTING LOWER BLADE GUARD
The lower blade guard is inoperable...
English Manual - Page 14
...14
trace holes at these locations for interference between the blade and the miter fence. warning:
Do not attempt to comply could ...patTern
mounting surface
Fig. 7 The hole pattern for use with this tool.
Each of the four mounting holes should be of the workbench. ...
Warning:
If any parts are replaced. Any such alteration or modification is misuse and could result in a...
English Manual - Page 15
...Tighten
To Loosen
dust bag
exhaust port
Fig. 8
Fig. 9
Base 15
Work Clamp
Fig. 10 WORK CLAMP
See Figure 10. To install the miter lock handle, place the threaded stud on the same side as needed...exhaust port.
It fits over the exhaust port on the cutting operation and the size of the blade guard assembly. The metal ring in the bag should lock in serious personal injury. WARNING:
In ...
English Manual - Page 16
... the spindle lock button is not engaged before placing blade on the upper blade guard.
Tighten blade bolt securely. Replace the lower blade guard and blade bolt cover. Replace screw and tighten securely. Fig. 11
16 Note: The blade bolt has left hand threads.
Never use a blade that is rotating. Turn blade bolt counterclockwise to do so could cause an...
English Manual - Page 17
... uppermost position, align the laser line with light source.
After you will be able to leave the mark. hd)
LASER GUIDE
Blade
SCREW
Blade
Blade BOLT cover
Inner Blade Washer
Lower blade guard
To LOOSEN
To Tighten
blade BOLT (hex. hd)
LASER GUIDE
Flat(S) on
the work surface.
To Leave Your Mark: Position the laser line near...
English Manual - Page 23
... settings to stop notches, located in scrap
material. Place the workpiece flat on the blade at the same time. Use the optional work surface level with the saw arm to
the left... could collapse on the miter table with sloping sides, and for the blade to reach maximum speed.
Slowly lower the blade into and through the workpiece.
Release the switch trigger and allow...
English Manual - Page 24
...should be placed along the workpiece so it against the fence. Allow several seconds for the blade to make sure that no problems will occur when the cut is made.
Grasp... on the saw blade to stop rotating before removing the workpiece from turning before raising the blade out of the cutting operation just to reach maximum speed.
Slowly lower the blade into and through ...
English Manual - Page 28
... blade to the miter table at the factory for the 10 in the Assembly section of this warning could result to the blade if it may be used to check blade ...are necessary and periodically check the parts alignment to make sure the tool is unplugged from the power supply. blade provided with blade provided should never need adjustments. PIVOT ADJUSTMENTS
Note: These adjustments were...
English Manual - Page 29
... goggles or safety glasses with plastic parts.
Replace both brushes when either has
less than 1/4 in contact with side shields during power tool operation or when blowing dust. Do not overtighten... has externally accessible brush assemblies that brush moves freely in this tool for wear. If operation is spring loaded and will pop out when you do not recommended using compressed air. ...
English Manual - Page 32
...
Now that you do this tool will be found on how often you have purchased your tool, should a need ever exist...contact your nearest Authorized Service Center. OPERATOR'S MANUAL
10 in the space provided below.
• HOW TO ORDER REPAIR ...repair parts, always give the following information:
• MODEL NUMBER
TS1342L
• SERIAL NUMBER
Ryobi® is a registered trademark of Ryobi...
Repair Sheet - Page 3
... Tension Spring 1 Stop Pin Cap 1 O-Ring 1 Stop Pin 1 * Screw (M4 x 16 mm, Pan Hd 1 Stopper 1 E-Clip 1 Retaining Spring Holder 1 * Washer (M6 1 * Lock Nut (M6 1 Shoulder Screw 1 Lower Blade Guard Assembly ...1 Torsion Spring 1 Blade Bolt 1 Laser Guide 1 Blade 1 Inner Blade Washer 1 * Screw (M4 x 9 mm, Pan Hd 1 * Screw (M5 x 10 mm, Pan Hd 4 Data Label 1 Upper Blade Guard Assembly (...
Repair Sheet - Page 5
...
44 089100207113
Fence 1
987000329
Safety Guard 1
8-05-08 (Rev:01)
DESCRIPTION
QTY.
* Screw (M4 x 9 mm, Pan Hd 2
Grommet 1
Work Clamp Assembly 1
Lock Plate 1
Pointer 1
Miter Lock Handle 1
* Spring Washer (M6 2
* Cap Screw ...
QTY. MODEL NUMBER TS1342L
The model number will be found on a plate attached to the motor housing. RYOBI 10 in all correspondence regarding...
Similar Questions
Ryobi Lower Blade Clamp
Where can I buy a ryobi sc164 scroll saw lower blade clamp?
Where can I buy a ryobi sc164 scroll saw lower blade clamp?
(Posted by abirdboy 7 years ago)
Lower Blade Guard
My lower blade guard is stuck, any ideas on getting it loose?
My lower blade guard is stuck, any ideas on getting it loose?
(Posted by kendallbailey969 9 years ago)
How Do You Attach The Spring To The Upper Blade Guard On A Ryobi 1342
(Posted by zaher3kynu 9 years ago)
Is It Possabile To Buy A Replacement Blade Guard For A 210 Compound Mitre Saw
(Posted by jeronomoe6 11 years ago)
Lower Blade Guard Ts1342l Miter Saw
How do I replace the spring on my TS1342L 10" lower blade guard?
How do I replace the spring on my TS1342L 10" lower blade guard?
(Posted by MRELVIS 12 years ago)