Ryobi SC164VS Support and Manuals
Get Help and Manuals for this Ryobi item
View All Support Options Below
Free Ryobi SC164VS manuals!
Problems with Ryobi SC164VS?
Ask a Question
Free Ryobi SC164VS manuals!
Problems with Ryobi SC164VS?
Ask a Question
Most Recent Ryobi SC164VS Questions
Ryobi Lower Blade Clamp
Where can I buy a ryobi sc164 scroll saw lower blade clamp?
Where can I buy a ryobi sc164 scroll saw lower blade clamp?
(Posted by abirdboy 7 years ago)
Popular Ryobi SC164VS Manual Pages
English Manual - Page 1
... will give you for dependability, ease of injury, the user must read and understand the operator's manual before using
this product.
Thank you years of rugged, trouble-free performance. SCROLL SAW VARIABLE SPEED
SC164VS
15 0
Your scroll saw has been engineered and manufactured to our high standard for your purchase.
OPERATOR'S MANUAL
16 in. SAVE THIS MANUAL FOR FUTURE REFERENCE
30
English Manual - Page 6
...completely the operator's manual.
SAVE THESE INSTRUCTIONS
6 CAUTION:
Indicates a potentially hazardous situation, which, if not avoided, may result in minor or moderate injury. We recommend Wide Vision Safety Mask for assistance.
Call Ryobi customer service for use over ...with side shields and, when needed, a full face shield. Always use only identical replacement parts.
English Manual - Page 9
...
THROAT PLATE
BLADE CLAMP SCREWS
30
DROP
15
FOOT
0
BEVEL SCALE
TABLE LOCK KNOB
SAW TABLE
SWITCH AND SWITCH KEY SAWDUST
EXHAUST
VARIABLE SPEED KNOB
MOTOR Fig. 2
9 FEATURES
PRODUCT SPECIFICATIONS
Throat 16 in ., pin or plain Input 120 V, 60 Hz, AC Only, 1.2 A
No Load Speed 400-1,600 r/min. (SPM) Net Weight 28 lbs. Blade Length 5 in...
English Manual - Page 10
... attach any 1-1/4 in a location inaccessible to children and others not qualified to use of this operator's manual as well as a knowledge of the workpiece to prevent the workpiece from the high speed ... the blade tension knob. SWITCH AND SWITCH KEY
Your scroll saw table, allows for maximum accuracy. The safe use the tool.
VARIABLE SPEED KNOB
Turn the knob to 45°.
For best ...
English Manual - Page 13
...SCROLL SAW TO WORKBENCH
See Figure 5. If the scroll saw is to be used in previous section called Mounting Scroll Saw to Workbench. Locate and mark the holes where scroll saw ... 3/4 in saw is recommended.
Mount saw to the bellows tube before starting the saw while in use.
thickness is being mounted to .
The tall, front part of saw . SAWDUST ...other supporting surface.
English Manual - Page 17
...speed of the lower blade holder. Pull up on either side then the drop foot must be adjusted. OPERATION
INSTALLING AND REMOVING BLADES
See Figure 11.
REMOVING THE SAW BLADE
Turn off and unplug the saw blades wear out quickly and must be replaced... Remove the blade. Scroll saw from under the blade holder in the V-notch of tension. Replace the throat plate. ...
English Manual - Page 18
...(0.3 mm)
3/32 in . Scroll saw blades generally stay sharp for straight and large curve cutting. The saw blades wear out and must guide the workpiece very slowly into the ...inch, the user must be cut with that blade is applied to the left.
18 ON OF F
15 30 45
TO INCREASE
TO DECREASE
Fig. 12
USING VARIABLE SPEED
See Figure 12. By turning the variable speed knob, the saw's speed...
English Manual - Page 19
...Install blade through the hole in the workpiece; You must attach the stacked pieces of a workpiece without pushing it - Use of commercial solvents and may be stacked on the saw table with the saw through the edge or perimeter of the board.
To make interior cuts in the workpiece, remove the scroll saw...identical replacement parts. WARNING:
Do not at the same time. INTERIOR SCROLL ...
English Manual - Page 21
... any repair. Too much tension. 2. Blade twisting in manual. 3. Loose table or table resting
against motor.
4. Have the proper outlet installed by a qualified service technician.
1. Reduce side pressure on blade; Check mounting. 2.
Loose motor mounting. SOLUTION
1. Tighten table lock knob.
4.
Blade holders out of saw. 2.
Have worn parts replaced before using scroll saw is...
English Manual - Page 22
... lumber. Please call or visit. OPERATOR'S MANUAL
16 in the space provided below.
• HOW TO ORDER REPAIR PARTS
When ordering repair parts, always give the following information:
• MODEL NUMBER • SERIAL NUMBER
SC164VS
Ryobi® is a registered trademark of Authorized Service Centers.
• MODEL NO. SCROLL SAW VARIABLE SPEED
SC164VS
WARNING:
Some dust created by power...
Repair Sheet - Page 1
SC164VS REPAIR SHEET RYOBI 16 in. (406 mm) SCROLL SAW
MODEL NO.
Repair Sheet - Page 2
MODEL SC164VS
82
55 11
24
65
23
16
57 66
11
95
21
28
93
94
22
20
29 25 27 70
25
16
41
93 75
35
58
84
49
83
76
78
4
9
68
3
6
4
28 25 56
67
26
23
24 88 34 30 16 69 61
48 87
47
3116
77
51
80...
50 85 89
81
3
7 8
10
18
73
17 18 19 4
13 14
53
18 54
36
33 44 74 72 86
2
5
73
12
15
63
2 RYOBI 16 in. (406 mm) SCROLL SAW -
Repair Sheet - Page 3
... Scroll Saw or when ordering repair parts. PARTS LIST
Key Part
Key Part
No. Number
Description
Qty. For the service center nearest you call 1-800-525-2579.
* Standard Hardware Item - Any repairs requiring disassembly of a double insulated tool can result in . (406 mm) SCROLL SAW - May Be Purchased Locally 3 RYOBI 16 in damage to the motor housing.
MODEL SC164VS
The model number...
Repair Sheet - Page 4
... S1605011
VARIABLE SPEED KNOB ...MANUAL
2-14-08
(REV:01)
* Standard Hardware Item - MODEL SC164VS
The model number will be found on a plate attached to the motor housing. No. Number
Description
Qty. May Be Purchased Locally 4
Always mention the model number in . (406 mm) SCROLL SAW - RYOBI 16 in all correspondence regarding your Scroll Saw or when ordering repair parts. Key Part...
Repair Sheet - Page 5
MODEL SC164VS
CIRCUIT BOARD
BLACK WHITE
MOTOR
BLACK
WHITE
RED RED
SPEED KNOB
SWITCH
POWER CORD
WHITE BLACK
GREEN
WIRING DIAGRAM
5 RYOBI 16 in. (406 mm) SCROLL SAW -
Ryobi SC164VS Reviews
We have not received any reviews for Ryobi yet.