Pioneer VSX-50 Support Question
Pioneer VSX-50 Support Question
Find answers below for this question about Pioneer VSX-50.Need a Pioneer VSX-50 manual? We have 1 online manual for this item!
Question posted by Rmerrifieldz on May 29th, 2016
Pioneer Vsx-50 Reset
Receiver turns on but no sound for about 20 minutes when it suddenly comes on. Followed directions for reset. RESET-No comes up but does not respond to controls, then turns off. Also does not respond to Receiver button on remote.
Current Answers
Answer #1: Posted by waelsaidani1 on May 30th, 2016 6:04 AM
waelsaidani1
Member since:
May 12th, 2013 Points: 19,501,797
Member since:
May 12th, 2013 Points: 19,501,797
Use this procedure to reset all the receiver's
settings to the factory default. Use the front panel
controls to do this. Set MULTI-ZONE to OFF.
R26; Disconnect the iPod and USB memory
device from the receiver beforehand.
1
Switch the receiver into standby.
2
While holding down ENTER on the front
panel, press =557; STANDBY/ON.
The display shows RESET =539; NO =540;.
Select 'RESET' using PRESET =547;/=548;, then
3
press ENTER on the front panel.
The display shows RESET? OK.
4
Press ENTER to confirm.
OK appears in the display to indicate that the
receiver has been reset to the factory default settings.
Related Pioneer VSX-50 Manual Pages
Owner's Manual - Page 4
... receivers 53 Setting the remote to control other components 53 Selecting preset codes directly 53 Programming signals from other remote controls 54 Erasing one of the remote control button settings 54 Erasing all learnt settings that are in one input function 54 Direct function 54
Multi Operation and System Off 55 Resetting the remote control settings......... 56 Controlling components...
Owner's Manual - Page 10
... DIRECT CONTROL
ENTER
PHONES
MCACC SETUP MIC
5V 2.1 A
iPod iPhone
iPad
USB
HDMI 2 INPUT
8
VSX-51
MASTER VOLUME
9 10 11
12 13 14
MCACC SETUP MIC
VIDEO 2 INPUT
5V 2.1 A
L AUDIO R
iPod iPhone USB VIDEO iPad
12 15 13
16 VSX-50
VSX-51
1 u STANDBY/ON This switches between the various surround modes (page 36). ! lights when the component...
Owner's Manual - Page 11
...VSX-50 are the same except where noted. Plugging in should be difficult. The RS-232C terminal is exclusively for WIRELESS LAN
LAN (10/100)
COAXIAL ASSIGNABLE IN 1 IN 2
IN 1
IN 2
OPTICAL
ASSIGNABLE
CONTROL IN
OUT IR IN
VIDEO ZONE 2
AUDIO...chapter explains the kinds of components you can connect to make up your equipment
This receiver provides you with many connection possibilities, but it ...
Owner's Manual - Page 17
... OPTICAL
Select one
VIDEO OUT VIDEO
COMPONENT VIDEO OUT
PR
PB
Y
HDMI OUT
HDMI OUT
HDMI IN
Select one
DIGITAL OUT
AUDIO OUT
COAXIAL OPTICAL
R ANALOG L
VSX-51 only
This connection is no need to tell the receiver which digital input you connected the player to the sound of the TV is input to the...
Owner's Manual - Page 19
... 1
ASSIGNABLE IN 2
IN 1
IN 2
OPTICAL
ASSIGNABLE
CONTROL IN
OUT IR IN
VIDEO ZONE 2
AUDIO DVR/BDR CD-R/TAPE ZONE 2
(OUTPUT 5 V ...receiver or other audio components
This receiver has both digital and analog inputs, allowing you to connect audio components for playback. When you set up the receiver you'll need to tell the receiver which input you connected the component to the receiver...
Owner's Manual - Page 20
.... To fix the stand to ZONE 2. to 20 ft.) length of VSX-50
Sub Zone Input functions available
ZONE 2
DVD, TV/SAT, DVR/BDR, VIDEO 1, VIDEO 2, CD, CD-R/TAPE, TUNER, ADAPTER PORT (Output analog audio only.)
It is clear.
4 Place the AM antenna on a flat surface and in a direction giving the best reception.
5 Connect the...
Owner's Manual - Page 36
...control (ALC) mode, this receiver, you can listen to sources using the EFFECT parameter in surround sound
Using this receiver equalizes playback sound...simplest, most direct listening option...Audio options on page 47 ). ! Standard surround sound
The following modes provide basic surround sound...sound). Try different settings with various soundtracks to be selected by pressing the STEREO button...
Owner's Manual - Page 37
... display to PURE DIRECT. AUTO SURROUND - Plays back sound from the Speaker B in Setting the Audio options on the input signal and whether or not surround back speakers are calibration of the sound field by the MCACC system and the Phase Control effect. ! When listening through the options as described below. !
to the receiver operation
2 While...
Owner's Manual - Page 38
... in the following cases: - If the speaker distance is on and we recommend leaving Phase Control switched on the front panel lights. When the PURE DIRECT mode is
set to maximize the effect. If two waveforms are plugged in phase, preventing unwanted distortion and/or coloring of the sound signal.
When the HDMI audio output...
Owner's Manual - Page 44
... using an HDMI cable. ! In this receiver once it to ON to use the Control with HDMI-compatible component is input to the receiver via HDMI (see the operating instructions for a component connected to the receiver by HDMI connections, if the TV supports the HDMI ARC (Audio Return Channel) function, the sound of this to transfer signals from...
Owner's Manual - Page 45
.... If a listening mode other than Pioneer that supports the Control with PQLS Multi
Surround, PQLS works for all sources. The sound of TV programs or an external input connected to the TV can also be played
through the receiver from the Audio input terminals other than AUTO SURROUND, ALC, DIRECT, PURE DIRECT or STEREO is selected while...
Owner's Manual - Page 47
..., it is unavailable due to the
current source, settings and status of the receiver.
1 Press
to the receiver operation mode, then press AUDIO PARAMETER.
2 Use i/j to select the setting you want to surround sound at low volumes). DRC (Dynamic Range Control)
Adjusts the level of dynamic range for movie soundtracks optimized for phase shifting on...
Owner's Manual - Page 50
... or off when headphones are switched automatically according to the audio input signal. ! Using the MULTI-ZONE controls
The following table shows the possible MULTIZONE remote controls:
50 En Switches the MULTIZONE feature off all output to the B-speaker terminals, and the subwoofer. If this receiver is set to more than one zone also changes the...
Owner's Manual - Page 53
... codes for the receiver ("Receiver 1" to "Receiver 4") you have multiple Pioneer receivers, amplifiers, etc., this receiver. The LED blinks once and flashes continuously. See Multi Operation and System Off on page 54 .
Release the button after the LED flashes once. Devices may be learned directly. If the desired operations cannot be set the remote control setting. ! See Erasing...
Owner's Manual - Page 54
... Pioneer format only). The LED continues to exit the preset setup mode. If the LED lights for one input function on this receiver's remote control. Note that have programmed and restores the button to the factory default.
1 Press and hold RCU SETUP, then press '7' for the other components you want to exit the erasing mode. Direct...
Owner's Manual - Page 56
... / DTV MPX PQLS
S.RETRIEVER
1
2
AUDIO 3
SIGNAL SEL MCACC SLEEP INFO
4
5
6
DISP
CH LEVEL A.ATT DIMMER
7
8
9
D.ACCESS
CLASS CH
/ CLR
0
ENTER
AUTO / ALC / DIRECT STEREO STANDARD ADV SURR
LISTENING MODE
RECEIVER
56 En
Controlling components
This remote control can control components after entering the proper codes (see Setting the remote to reset all the signals
learned in...
Owner's Manual - Page 72
...component has a digital volume control, make sure it 's connected to NO (see The Input Setup menu on page 13 ).
Broadcast stations cannot be able to Speaker B and audio is selected with Dolby Digital/ DTS discs.
Noise may be output from receiver during playback. No sound... button, no sound will be caused by interference from subwoofer. Adjust the position and direction of...
Owner's Manual - Page 75
...playing DVD-Audio material ...turn on the disc, the Dolby Digital or DTS is performed, but due to display when using another remote control...Control Mode Setup on the receiver. If they still do not output these adjustments in the remote control (see Choosing the input signal on to achieve optimal sound...Pioneer components with this is no obstacles between the receiver and the remote control...
Owner's Manual - Page 78
... 12 is performed from the receiver or remote control.
Try using another server.
Audio playback is set . There are listed in the list of Internet radio stations on . Check whether the connection status is undesirably stopped or disturbed. Switch on the audio component on the network before switching on the component connected to "Do not authorize...
Owner's Manual - Page 84
... you to restore sound pressure and smooth jagged artifacts left over after compression. 13 Additional information
Decoding A technology for converting digital signals that supports the Control with HDMI functions are possible when the component is connected to be optimal for the volume level.
Network function
AirPlay This receiver supports AirPlay audio streaming from Microsoft...
Similar Questions
How Do I Reset A Pioneer Vsx-55txi Receiver
how do I reset a pioneer vsx-55txi receiver ?
how do I reset a pioneer vsx-55txi receiver ?
(Posted by 9393 3 years ago)
Factory Reset Pioneer Vsx D209 Receiver
How do I Factory reset Pioneer VSX D209 Receiver?
How do I Factory reset Pioneer VSX D209 Receiver?
(Posted by krash1111 7 years ago)
I Have A Pioneer Vsx-504s Receiver. Can I Plug A Digital Optical Cord From My Tv
(Posted by Jeffmoore 12 years ago)
Help With Pioneer Vsx 50
I can not get the guy screen up on my tv
I can not get the guy screen up on my tv
(Posted by Kpaterson303 12 years ago)