Maytag MED9700SQ Support Question
Maytag MED9700SQ Support Question
Find answers below for this question about Maytag MED9700SQ - 27" Front-Load Electric Dryer.Need a Maytag MED9700SQ manual? We have 1 online manual for this item!
Current Answers
Related Maytag MED9700SQ Manual Pages
Use and Care Guide - Page 3
...is , tell you how to cooking oils in the dryer. WARNING
You can be cleaned periodically by the manufacturer of the fabric softener or product.
■ Do not use heat to dry articles ... risk of fire, electric shock, or injury to a chemical reaction that can happen if the instructions are very important. Always read and obey all instructions before or after each load. ■ Keep ...
Use and Care Guide - Page 4
... instructions provided with clothes dryers. For a garage installation, you will need to purchase a Stack Kit. Check existing electrical supply and venting. The...9632; Tape measure
Parts supplied Remove parts packages from dryer drum.
You will add to the "Assistance or Service" section. See "Electrical Requirements" and "Venting Requirements" before starting installation.
The...
Use and Care Guide - Page 5
... 18" (46 cm) to support the total dryer weight of the dryer in death, explosion, or fire. If using a power supply cord, a grounded electrical outlet located within 2 ft
(61 cm) of... shut off at least 18" (46 cm) above the floor for this dryer.
Dryer only
0" (0 cm)
38" min. (96.52 cm)
*Required spacing
1"* (2.5 cm)
27" (68.6 cm)
1"* (2.5 cm)
5
The combined weight
of a companion...
Use and Care Guide - Page 6
..." (68.6 cm)
A
1"
1"*
(2.5 cm) (2.5 cm)
31½" (80 cm)
B
5"** (12.7 cm)
A. Recessed area B. Side view -
Closet door with stacked washer and dryer
The dimensions shown are required.
7"* (17.8 cm) 7"* (17.8 cm)
9"* (22.9 cm)
5"** 31¹ ₂" 1"*
1" 27" 1"
(12.7 cm) (80.0 cm) (2.5 cm) (2.5 cm)(68.6 cm) (2.5 cm)
*Required spacing **For side or bottom venting, 0" (0 cm...
Use and Care Guide - Page 7
... (center or white wire) of the terminal block, the dryer cabinet is adequate. Connect to install with a 3-wire electrical supply connection. Do not have a fuse in the neutral ...cm)
76" (193 cm)
*Required spacing
5"* (12.7 cm)
1" (2.5 cm)
27" (68.6 cm)
1" (2.5 cm)
Mobile home -
If the dryer is installed in mobile homes to the neutral wire, see "Optional 3-wire connection" section....
Use and Care Guide - Page 8
... cord with flexible metallic conduit. GROUNDING INSTRUCTIONS
■ For a grounded, cord-connected dryer: This dryer must be : ■ Flexible armored cable or nonmetallic sheathed copper cable (with ground... dryer: This dryer must be connected to the equipment-grounding terminal or lead on the power supply cord: if it will reduce the risk of electric shock by providing a path of electric ...
Use and Care Guide - Page 9
... a CSA International Certified Power Cord intended to do so can result in death or electrical shock.
Electrical Shock Hazard
Plug into a standard 14-30R wall receptacle. Failure to be grounded. Connect to whether the dryer is recommended that the electrical connection is adequate and in doubt as to an individual branch circuit.
■ This...
Use and Care Guide - Page 11
... Reaching inside the strain relief. The strain relief should have a tight fit with the dryer cabinet and be in a horizontal position. Tighten strain relief screw against the direct wire ... relief (UL marking on the power supply cord is not available)
Electrical Connection Options
If your type of electrical connection: 4-wire (recommended)
3-wire (if 4-wire is inside the...
Use and Care Guide - Page 12
...
A. External ground conductor screw - down screw. 7. Direct wire cable must have completed your electrical connection. Spade terminals with hold- Ring terminals
1.
Tighten screws. Dotted line shows position of ...screw. B. Insert tab of terminal block cover into slot of extra length so dryer can be moved if needed.
12 4-wire connection: Power supply cord
IMPORTANT: ...
Use and Care Guide - Page 13
... cable to the terminal block, place the hooked end of the wire under the screw of dryer rear panel. Place the hooked ends of wires into slot of
the terminal block (hook facing...squeeze hooked end together and tighten screw, as
shown. Tighten screws.
You have completed your electrical connection. Now go to center silver-colored terminal block screw.
Shape
ends of the other direct...
Use and Care Guide - Page 14
... 3-wire cable with ground wire, cut bare wire even with outer covering. Shape ends of wires into slot of dryer rear panel. Center silver-colored terminal block screw D. B
D
E
A
C
GF
A. 3-wire receptacle (NEMA ... terminal block screw.
2. Direct wire cable must have completed your electrical connection. Insert tab of terminal block cover into a hook shape.
1" (2.5
cm)
...
Use and Care Guide - Page 15
...hooked ends together. Tighten strain relief screw. 5. You have completed your electrical connection. Neutral ground wire D. Grounding path determined by a qualified electrician...conductor screw to neutral wire. 1. Center silver-colored terminal block screw D. Place the hooked ends of dryer rear panel.
Tighten screw. B A
C
E
D
E
A. down screw. 6.
Secure cover with...
Use and Care Guide - Page 17
..., snow line, etc.). ■ Do not use an exhaust hood with one of the dryer. Left or right side exhaust installation C. Improper venting can cause moisture and lint to collect indoors, which may result in death, fire, electrical shock, or serious injury.
Wall D. Clamps F. Exhaust outlet
17 WARNING
Fire Hazard Cover unused...
Use and Care Guide - Page 23
...to an Automatic Cycle.
■ Select DRYNESS LEVEL to adjust how dry you want the load to select either an Automatic or Manual Cycle then press the CONTROL ON button. The time... Level selected.
Place laundry in death or fire.
WARNING: To reduce the risk of this appliance. Please refer to specific sections of fire, electric shock, or injury to start your dryer.
See "Cleaning the...
Use and Care Guide - Page 25
...light illuminates until : ■ The damp dry point is reached in handling. Laundry is cooling down .
■ In a Manual Cycle, if a wet item ...you are drying. The Cycle Complete light turns off and the dryer will also be on the control panel show Cycle, Temperature ...option is enabled.
Cycles
Select the drying cycle that the load has reached the damp dry level.
NOTE: The Damp ...
Use and Care Guide - Page 26
..., jeans
NORMAL Corduroys, work clothes
TOUCHUP
Medium
20
Helps to smooth out wrinkles
RAPID DRY Small loads
High
27
Additional Features
Extra Care Feature When you do not select the Extra Care feature, the dryer stops after an Automatic Cycle. Temperature Temperature settings are securely stitched. ■ Shake and fluff pillows by pressing...
Use and Care Guide - Page 28
As needed cleaning Laundry detergent and fabric softener residue can result in the door opening of the dryer. To wash
1. Cleaning the Lint Screen
Every load cleaning The lint screen is ...are removed.
3. The screen is probably clogged if lint falls off the screen with your load is in dryer. Scrub lint screen with a damp cloth. 4. Failure to remove residue buildup.
Wipe drum ...
Use and Care Guide - Page 30
...
Clothes are not drying satisfactorily, drying times are intact and tight, or that both fuses are too long, or load is the dryer level front to back and side to side? Electric dryers require 240-volt power supply. Check the front and rear edges of the drum for a while, there may not have not...
Use and Care Guide - Page 31
... for most installations, the rear of the door. Add dryer fabric softener sheets at the top and bottom of the dryer requires 5" (12.7 cm). When the odors or fumes are gone from dryer. Separate the load to a partially dried load can tumble freely. The new electric heating element may not be gone after the first cycle...
Use and Care Guide - Page 32
...dryer cord, 3-wire, 30 amp 4 ft (1.2 m) dryer cord, 4-wire, 30 amp 6 ft (1.8 m) dryer cord, 4-wire, 30 amp Dryer vent lint brush All-purpose appliance cleaner Laundry supply storage cart LP Gas conversion kit Door reversal kit (all colors) Drying rack Stack... and repair parts sales.
■ Referrals to fulfill the product warranty and provide after -warranty service, anywhere in your appliance...
Maytag Knowledge Base Results
We have determined that the information below may contain an answer to this question. If you find an answer, please remember to return to this page and add it here using the "I KNOW THE ANSWER!" button above. It's that easy to earn points!-
Loads are damp; dryer does not dry
... possible causes and solutions. Loads are many reasons why your loads may change the preset Dryness level settings to increase the dryness. This change will affect all Sensor Dry cycles. the dryer does not dry. Dryer Dryer does not heat - Electric Dryer Dryer does not heat - Gas Dryer Cycle is shown. Gas dryer Damp loads or long drying times... -
My dryer or load has an odor
... remove the odors. Promptly remove loads from the area, rewash and dry the load. The odor will result in the washer or dryer? My dryer or load has an odor Have you recently been painting, staining or varnishing in the washer or dryer for the first time? (Electric dryers) A new electric heating element may have an odor... -
Dryer does not heat - Gas dryer
...parallel to the gas pipe. See the Installation Instructions for details. - Expect loads dried with the Air Fluff or Air Only temperature to take longer to the dryer. Dryer does not heat - The Air Fluff or Air Only temperature does not ... gas shutoff valve in the supply line. The valve is open when the handle is closed. Electric dryer Gas dryer My gas dryer does not .
Similar Questions
Maytag Front Load Electric Dryer Won't Start
(Posted by nuriterry 9 years ago)
Maytag Electric Dryer Med9700sq0 Troubleshooting Won't Heat
(Posted by alborgblkw 10 years ago)
Maytag Epic Electric Dryer, Model# Med9700sq - Not Heating
My Matag Epic Electric Front Load Dryer (model # MED9700SQ, is not heating up. The drum turns and ev...
My Matag Epic Electric Front Load Dryer (model # MED9700SQ, is not heating up. The drum turns and ev...
(Posted by Anonymous-122272 10 years ago)
I Have A Maytag Front Loading Electric Dryer Model Med9600 Sq0. When I Attempt T
I have a Maytag front loading electric Dryer model MED9600 SQ0. When I attempt to start it by pressi...
I have a Maytag front loading electric Dryer model MED9600 SQ0. When I attempt to start it by pressi...
(Posted by wrzimmerly 10 years ago)
Maytag Epic Electric Dryer Med9700sq Makes Squeaking Noise
I pulled the bottom of the dryer off and found a large roller that turns the drum. That is where the...
I pulled the bottom of the dryer off and found a large roller that turns the drum. That is where the...
(Posted by classactcowgirl 12 years ago)