Kenmore HE2t Support Question
Kenmore HE2t Support Question
Find answers below for this question about Kenmore HE2t - 3.7 cu. Ft. Front Load Washer.Need a Kenmore HE2t manual? We have 1 online manual for this item!
Question posted by hallieslayter on September 18th, 2014
Troubleshooting Leak
Water drip at bottom of front door. Looking for fix.
Current Answers
Answer #1: Posted by BusterDoogen on September 18th, 2014 10:54 AM
BusterDoogen
Member since:
October 30th, 2011 Points: 28,565,407
Member since:
October 30th, 2011 Points: 28,565,407
If the washer is leaking water the front door boot seal might have a tear or rip and is letting water leak past. The boot seal can be replaced. This part can tear when the washer is overloaded. This is common repair. Be sure to insert the full model # of your washer for the exact part.
I hope this is helpful to you!
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful. Please feel free to submit further info for your question, if a solution was not provided. I appreciate the opportunity to serve you!
Answer #2: Posted by Brainerd on September 18th, 2014 10:35 AM
Brainerd
Member since:
May 24th, 2014 Points: 759,630
Member since:
May 24th, 2014 Points: 759,630
Hi, please refer to the inatructions in the link below:
http://www.justanswer.com/appliance/4s5si-kenmore-he2-plus-leaking-water-bottom.html
http://www.justanswer.com/appliance/4s5si-kenmore-he2-plus-leaking-water-bottom.html
I hope this helps you!
Please press accept to reward my effort or post again with more details if not satisfied.
Regards, Brainerd
Related Kenmore HE2t Manual Pages
User Guide - Page 1
CONSUMER SERVICES TECHNICAL
EDUCATION GROUP PRESENTS L-78
FRONT-LOADING AUTOMATIC WASHER
MODELS: WFW8300SW, WFW8500SW, WFW8500SR
JOB AID Part No. 8178558
User Guide - Page 2
... only.
FORWARD
This Whirlpool Job Aid, "Duet Sport™ Front-Loading Automatic Washer" (Part No. 8178558), provides the technician with information on the installation, operation, and service of this Job Aid are to:
• Understand and follow proper safety precautions. • Successfully troubleshoot and diagnose malfunctions. • Successfully perform necessary repairs. •...
User Guide - Page 3
... Use 3-3 Washer Care 3-12 Troubleshooting 3-15
COMPONENT ACCESS 4-1 Component Locations 4-1 Removing The Console And The Touchpad/LED Assembly 4-2 Removing The Central Control Unit 4-4 Removing The Water Inlet Valve 4-6 ... Filter 5-3 Detergent Dispenser Motor & Switch 5-4 Door Switch 5-5 Drain Pump 5-6 Temperature Sensor & Heater 5-7 Drive Motor 5-8 Interlock Switch 5-8
- iii -
User Guide - Page 4
iv - Removal Or Replacement 6-8 Washer Care 6-9
Troubleshooting Guide 6-11 WIRING DIAGRAMS 7-1
Washer 7-1 Grounding System 7-2
- Page DIAGNOSTICS & TROUBLESHOOTING 6-1
Diagnostics 6-1 Diagnostic Guide 6-1 Failure/Error Display Codes 6-2 Diagnostic Test 6-5 Error History Display 6-6 History Overview Test Program 6-6 Manual Diagnostic Test 6-7 Manual Overview Test Program 6-7 ...
User Guide - Page 6
MODEL & SERIAL NUMBER DESIGNATIONS
MODEL NUMBER
MODEL NUMBER
W F W 8 3 00 S W 0
BRAND W = Whirlpool
ACCESS F = Front Loading
PRODUCT W = Washer
SERIES 5 = Whirlpool Leap 7 = 24˝ Front Load 9 = Duet Front Load
6 = Oasis 8 = Mid Line Front Load
PRICE POINT LEVELS (1 - 9)
TRADE PARTNER ID (00 = BRANDED)
YEAR OF INTRODUCTION S = 2006, T = 2007
COLOR CODE T = Biscuit Q = White W = ...
User Guide - Page 8
... Number Model Description
Color
Capacity (Cu.Ft. IEC) Temperature Control
Heater Sensors
Tumble Speed
Spin Speed
Motor Voltage Frequency Amps Water Consumption Average DOE (Gallons-Per-Cycle) Rated Load Load Pounds
Height Install Depth: Min - Max
Width Product Weight (approx)
WFW8300SW
WFW8500SW
WFW8500SR
Front Load Washer
Front Load Washer
Front Load Washer
White with Gray Accents
White...
User Guide - Page 9
Tools needed for this washer. and connector kit, Part Number 2858835
4 ft (1.2 m) drain hose extension kit, Part Number 2858863
2 longer water fill hoses: 6 ft (1.8 m) Part Number 76314 10 ft (3.0 m) Part Number 350008
A
... tape
Parts supplied
If You Have Laundry tub or standpipe taller than 96" (2.4 m) Overhead sewer
Floor drain
Drain hose too short Water faucets beyond reach of fill hoses
...
User Guide - Page 10
... load) of 400 lbs (180 kg). Ask for wall, door, and floor moldings.
• Additional spacing of 1˝ (2.5 cm) on soft floor surfaces, such as carpets or surfaces with foam backing, is your washer in a basement, laundry room, closet, or recessed area. See "Electrical Requirements."
• Hot and cold water faucets located within 6 ft (1.8 m) of where...
User Guide - Page 14
.... These bolts also retain the power cord inside the washer until it to the water faucets
Make sure the washer drum is to the hot water faucet. Excessive Weight Hazard Use two or more people ...to do so can result. Failure to move it is within approximately 3 ft (90...
User Guide - Page 15
... on the hoses for leaks.
Using pliers, tighten the couplings with an additional two-thirds turn. Bend drain hose over drain hose form and snap into a laundry tub, drainpipe or bucket, to the cold water faucet. Record hose installation or replacement dates on the washer.
2.
NOTE: Do not overtighten. Damage to water leakage. B.
Remove drain...
User Guide - Page 17
... grounding method. Do not use an extension cord. Read "Washer Use." 9. Allow the washer to see which step was skipped.
3. COMPLETE INSTALLATION
1. ...a grounded 3 prong outlet. 8. Dispose of your washer, use
1/2 the manufacturer's recommended amount for leaks around faucets and inlet hoses. Be sure that you...water faucets are now installed.
Check for a medium sized...
User Guide - Page 19
..., reducing drying time.
You are evenly balanced.
3-1
SUSPENSION SYSTEM
To reduce washer "walk" and "off -balance loads during spinning, it redistributes the clothes so that clothes coming out of water is available in which means fewer loads. When this feature allows the washer to use whether you can handle slow speeds needed for the fi...
User Guide - Page 22
... amount of the tub for this type of fabric. To load washer
Open the washer door by pulling on the washer by turning the cycle selector. See "Options."
6. This wash system, along with less water, will illuminate. This initial cycle serves to select ON or OFF.
7. Load evenly.
• Wash small items such as it firmly...
User Guide - Page 24
...water level or the temperature is complete, the door unlocks. To change Options after the wash cycle. To drain the washer manually
1. Select and hold START (for approximately 1 second) to restart the washer...load.
• Always measure liquid chlorine bleach. Items can be changed anytime before the door unlocks. do not guess. The liquid detergent flows immediately into the washer....
User Guide - Page 27
... cycles.
• See the "Laundry Guide" section for an overview of synthetics, delicate fabrics, handwashables, and woolens should be a short tone and the light for :
• Loads that option will show in stains.
Between changes in the Estimated Time Remaining display. • Select START. See "Troubleshooting."
See "Cleaning The Washer." This cycle combines fast...
User Guide - Page 34
... dry between uses. This washer has a tight seal to the washer basket. Select DRAIN/SPIN to carry away 17 gal. (64 L) of the door, when the door is normal. Press PAUSE/CANCEL once. LEAKING
• Was the door opened after use the chlorine bleach dispenser for leaks. Check household plumbing (laundry tubs, faucets, drainpipe, water pipes) for color-safe...
User Guide - Page 35
... bolts removed? Do not use an adapter. Straighten the hoses.
• Are the water inlet valve screens clogged? The washer pauses for leaks.
• Is the washer in a normal pause in the standpipe, or is used.
• Is the load balanced? The door must be closed again to the standpipe?
The hose needs an air gap...
User Guide - Page 36
... evenly distribute your wet laundry in a load. If the laundry is still wet, take half of the load out of load you overloaded the washer? The washer can occur when mixing whites and colors in the drum, and start to redistribute the load with additional tumbling.
• Did you wash a large load on your hot water system is complete, then...
User Guide - Page 87
...solution, using 3/4 cup (177 mL) of liquid chlorine bleach, and 1 gal. (3.8 L) of warm tap water. To remove the touchpad/LED assembly:
1. Remove left front screw that was covered by pressing PAUSE/CANCEL. ...Remove the two screws which secure the line filter to release right side of the washer. Open the washer door and remove any clothing or items from the CCU.
3. Pull back the seal to ...
User Guide - Page 91
WIRING DIAGRAMS
WASHER
N L
IF
DOOR LOCK/SWITCH
DS
DLS
Lock Unlock
IF2
DS2
DL3
DLS2
1
2
12 1 2 3
1 2
DRIVE MOTOR
MOTOR CONTROL UNIT (MCU)
L2 N1
MS2
1
2
MI3 1 2 3
HEATING ELEMENT DRAIN PUMP
...
Similar Questions
What Is The Purpose Of Running A Diagnostic Test On Kenmore Front Load Washer
(Posted by dabawa 10 years ago)
Kenmore He2t Front Loading Washer Model# 110.4756
When I turn power on the front panel lights up, but when I push start it all shuts down. Tried unplu...
When I turn power on the front panel lights up, but when I push start it all shuts down. Tried unplu...
(Posted by cpcalder 11 years ago)
What Does It Mean When A Kenmore Front Load Washer Model # 48102 Turns Off And O
what does it mean when a kenmore front load washer model # 48102 turns off and on during the washing...
what does it mean when a kenmore front load washer model # 48102 turns off and on during the washing...
(Posted by kemackey86 11 years ago)
Why Front Load Washer 4044 Won't Start The Cycle?
Yesterday while my front load washer 4044 was starting to do its first normal cycle , which usually ...
Yesterday while my front load washer 4044 was starting to do its first normal cycle , which usually ...
(Posted by martinezmarly 11 years ago)
Does This Front Load Washer Need To Have Bolts Installed To Move From Another St
model#110.47571602 HE2t frontload washer locking bolts for moving?
model#110.47571602 HE2t frontload washer locking bolts for moving?
(Posted by donnasilver 12 years ago)