Kenmore HE2t Support Question
Kenmore HE2t Support Question
Find answers below for this question about Kenmore HE2t - 3.7 cu. Ft. Front Load Washer.Need a Kenmore HE2t manual? We have 1 online manual for this item!
Question posted by kkaya2 on February 3rd, 2013
Kenmore He2t Cycle Problems
My washer begins a wash cycle and after a few minutes give a error message "20 F" and stops the cycle. According to the manual it is a interuption in the water flow possibly caused by a kink in the water hoses. After rearranging the hoses the problem continues. What could be the cause of this problem and what is the best method to fix it?
Current Answers
Related Kenmore HE2t Manual Pages
User Guide - Page 8
...
Motor Voltage Frequency Amps Water Consumption Average DOE (Gallons-Per-Cycle) Rated Load Load Pounds
Height Install Depth: Min - Max
Width Product Weight (approx)
WFW8300SW
WFW8500SW
WFW8500SR
Front Load Washer
Front Load Washer
Front Load Washer
White with Gray Accents
White... (8 kg)
N/A
36.0" 30.00"
27" 242 lbs.
1-4 SPECIFICATIONS
Model Number Model Description
Color
Capacity (Cu.Ft.
User Guide - Page 19
... speed can obtain the same results with smaller amounts of the washer will illuminate for small and large loads size.
ADD A GARMENT
This option is available in which means fewer loads. This washer allows a 7-minute period in all wash cycles except Rinse/Spin and Drain/Spin. AUTO WATER LEVEL
Adjusting to the size of operation may be added...
User Guide - Page 22
... be used and that should close easily.
• Mix large and small items. Avoid washing a single item. Press END OF CYCLE SIGNAL to avoid spills. To load washer
Open the washer door by pulling on the washer by pushing it stops. The indicator light for the selected cycle will illuminate. Place a load of choosing a cycle, the washer automatically shuts off.
3-4 To begin .
User Guide - Page 23
... D. IMPORTANT: When delaying a cycle, use only powdered detergents in washer errors, longer cycle times, and reduced rinsing
performance. Do not put laundry additives directly into the wash tub. The washer powers down the washer manually after the cycle is complete and the CYCLE COMPLETE light goes off.
To power down automatically 5 minutes after the wash cycle is complete, select PAUSE...
User Guide - Page 24
.... NOTE: Overfilling could cause an oversudsing condition. Add no more than the manufacturer's recommended amount. To continue the cycle, select and hold START (for approximately 1 second) to your load.
• Always measure liquid chlorine bleach. Cycles and Options can be removed from the washer. To stop a cycle and select a new cycle
1. Select and hold START (for...
User Guide - Page 26
...ensure proper performance during this cycle to wash loads of 2-3 lightly soiled garments that you set your water pressure, water temperature, detergent, and clothes load. Normal/Casual
Use this cycle to clean heavily soiled, colorfast fabrics. Quick Wash
Use this cycle to wash small loads of no bleach is unbalanced. Delicate/Hand Wash
Use this cycle to wash sheer fabrics, lingerie, hand...
User Guide - Page 27
... all options are available with all cycles.
• See the "Laundry Guide" section for an overview of possible options for each Wash Cycle selection.
• If an option is preset to the wash cycle will be drained with liquid chlorine bleach to thoroughly clean the inside of your wash load.
Clean Washer
Use the Clean Washer cycle once a month to keep the...
User Guide - Page 28
....
3-10
You may be used to aid in "Cycles."
• ATC works for fabrics. Use the warmest wash water safe for the wash temperature with the same water temperature as it stops.
Cold rinses save energy. Select a water temperature based on the cold water at the faucet. Prewash
Use this option for loads of Cycle Signal
This signal is illuminated.
User Guide - Page 30
.... This will unlock. The door will take approximately 3 minutes.
7.
Begin procedure
1.
WASHER CARE
CLEANING THE WASHER
Cleaning the Door Seal/Bellow
1. A
A. b) Wipe the seal/bellow area with liquid chlorine bleach to inspect all the Cycle lights will flash and the WASH and CONTROLS LOCKED lights will cause damage to the unit and clothing added to check...
User Guide - Page 33
... the Estimated Time Remaining display (on some models).
• "Spin" and "Wash" (HT "Rinse" and "Cycle Complete") illuminated or "F20" on display (Water Inlet Problem-no water or insufficient water supply) Select PAUSE/CANCEL twice to washer clogged?
As with any new product, you washing items with metal snaps, buckles or zippers? These new sounds and...
User Guide - Page 35
... the hot and cold water faucets turned on the water.
• Is the water inlet hose kinked? WASHER OPERATION
WASHER WON'T RUN, FILL, RINSE, OR TUMBLE; Allow the cycle to start a new cycle. WASHER CONTINUES TO FILL OR DRAIN, DRAIN CYCLE SEEMS STUCK
• Is the top of the drain hose more items or redistribute the load. Cycle will see little or...
User Guide - Page 37
... unload the washer promptly? The wash load must be balanced and not overloaded.
Check that the hot and cold water hoses are connected to relax wrinkles? Powdered detergents may not dissolve well in a lowspeed cycle? Dispensing balls will cause wrinkling. If safe for load, use powdered detergent in a slow-speed cycle. Unload the washer as soon as it stops.
•...
User Guide - Page 80
... attempts to step 7. 7. Unplug washer or disconnect power. 2. Refer to 103°C]) during the first 40 minutes is not a siphon problem.
2. WATER TEMPERATURE SENSOR ERROR If the water temperature sensor (NTC) value is out of the WASH cycle.
PUMP DRIVE ERROR The pump driver fails to it. 3. Possible Causes/Procedure Replace CCU board.
MAIN RELAYS ERROR One of failure codes will be...
User Guide - Page 81
... be manually unlocked.
Possible Causes/Procedure Door lock mechanism is broken. NOTE: The door switch/lock unit can be to the left when facing the MCU connectors. Check dispenser motor for operations of the CLEANING WASHER cycle a load is detected inside the drum. Plug in washer or reconnect power.
5. Plug in washer or reconnect power. 4. Turn off .
7. Possible Causes/Procedure...
User Guide - Page 82
... of foreign objects. 5. Run a NORMAL cycle without tumbling, the water will rest without adding any
cycle. Check/clean drain pump filter of the excess detergent.
1. They use the status lights on the touchpad/LED. Check the pressure switch. 8. Possible Causes/Procedure If too much detergent was used: - Plug in washer or reconnect power. 6. Check wire harness...
User Guide - Page 83
...error states that have been recorded by the appliance.
• Run through an automated test.
• Run loads to start the test.
1.
Starting Service History Mode & Diagnostic Test:
NOTE: The washer...show the error history.
• Close the door.
• Push POWER.
• Select the CLEAN WASHER cycle.
•...for 5 seconds.
• Next the washer begins the Diagnostic Test.
• To cancel ...
User Guide - Page 85
... set to the beginning. For model Duet Sport... plus 10 sec).
Stop motor to maximum speed...minutes max.)
Drum executes reversing movement at wash speed (10 min).
Filling only by the Hot valve.
Filling with both valves.
Press/ hold 4 sec's., release
NOTES:
• Press the same key to advance to Bypass channel. Filling only by the Cold valve. MANUAL DIAGNOSTIC TEST
The washer...
User Guide - Page 87
... seal and to do so will stop the cycle. If stained areas are found, wipe down area thoroughly with a dry cloth and let the washer interior air dry with the dilute ...cycle.
6-9 Washer Maintenance Procedure
This washer has a special cycle that uses higher water volumes in the back of the CCU with liquid chlorine bleach to thoroughly rinse the remaining bleach from the unit. This will cause...
User Guide - Page 89
... in washer or reconnect power. 8. Check the touchpad/LED assembly by looking for plugged screen in water source. 4. CONTROL WON'T 1. Drain the unit, then check that the drain hose and drain pump filter are clear of foreign objects.
3. PROBLEM WON'T DISPENSE
WON'T FILL
OVER FILLS
DRUM WON'T ROTATE MOTOR OVERHEATS
POSSIBLE CAUSE/TEST
NOTE: Possible Cause/Tests...
User Guide - Page 90
.... 3. Plug in the sequence shown for an abnormal condition. Check wire harness connections. 3.
PROBLEM WON'T DRAIN
POSSIBLE CAUSE/TEST
NOTE: Possible Cause/Tests must be performed in washer or reconnect power.
6. Check drain pump. 4. Remove shipping system. 2. Check leveling feet. Check the water heater and wire harness connections to it.
4. MACHINE VIBRATES
1. Check...
Similar Questions
Where Is The Mcu Located On A Kenmore He2t Front Loading Washer
(Posted by DRobRoha 10 years ago)
Kenmore He2t 3.7-cubic-foot Front-loading Washer Wont Start
(Posted by flFe 10 years ago)
Kenmore He2t Front Loading Washer Model# 110.4756
When I turn power on the front panel lights up, but when I push start it all shuts down. Tried unplu...
When I turn power on the front panel lights up, but when I push start it all shuts down. Tried unplu...
(Posted by cpcalder 11 years ago)
What Does It Mean When A Kenmore Front Load Washer Model # 48102 Turns Off And O
what does it mean when a kenmore front load washer model # 48102 turns off and on during the washing...
what does it mean when a kenmore front load washer model # 48102 turns off and on during the washing...
(Posted by kemackey86 11 years ago)
Why Front Load Washer 4044 Won't Start The Cycle?
Yesterday while my front load washer 4044 was starting to do its first normal cycle , which usually ...
Yesterday while my front load washer 4044 was starting to do its first normal cycle , which usually ...
(Posted by martinezmarly 11 years ago)