Kenmore HE2t Support Question
Kenmore HE2t Support Question
Find answers below for this question about Kenmore HE2t - 3.7 cu. Ft. Front Load Washer.Need a Kenmore HE2t manual? We have 1 online manual for this item!
Question posted by Anonymous-105898 on April 2nd, 2013
Drain Hose
how do you get the drain hose back on the washer
Current Answers
Related Kenmore HE2t Manual Pages
User Guide - Page 8
SPECIFICATIONS
Model Number Model Description
Color
Capacity (Cu.Ft. Max
Width Product Weight (approx)
WFW8300SW
WFW8500SW
WFW8500SR
Front Load Washer
Front Load Washer
Front Load Washer
White with Gray Accents
White with Gray Accents
White with Sterling Bright Accents
3.3
3.6
3.6
ATC - 2
ATC - 4
ATC - 4
No
Yes
Yes
Suds Sensor, NTC (Thermistor), Water Level ...
User Guide - Page 9
... the washer drum. additional drain hose Part Number 8318155; and connector kit, Part Number 2858835
4 ft (1.2 m) drain hose extension kit, Part Number 2858863
2 longer water fill hoses: 6 ft (1.8 m) Part Number 76314 10 ft (3.0 ...measuring tape
Parts supplied
If You Have Laundry tub or standpipe taller than 96" (2.4 m) Overhead sewer
Floor drain
Drain hose too short Water faucets beyond reach of...
User Guide - Page 10
..."Drain System." Washer ...washer with a total weight (water and load) of 1˝ (2.5 ...ft (1.2 m) of the hot and cold water fill valves, and water pressure of 20-100 psi (137.9-689.6 kPa).
• A level floor with foam backing, is recommended to stack your washer improves performance and minimizes noise and possible washer "walk."
Some water can remain in a basement, laundry...
User Guide - Page 12
... a minimum of 28˝ (71 cm) from the bottom of the washer. The top of the laundry tub must be needed.
30" min. (76.2 cm)
26" min. (66 cm)
30" min. (76.2 cm)
A
B
A
B
2-4 Select the drain hose installation method you need. DRAIN SYSTEM
The washer can be no higher than 17 gal. (64 L) per minute. The...
User Guide - Page 15
...drain hose from the washer
Gently pull the corrugated drain hose from damage due to water leakage. Turn on the hoses for leaks. B.
Attach the hot water hose to the washer
H
C
H.
Run water through both faucets and inlet hoses...hot water hose is connected to the cold water faucet. Laundry tub drain or standpipe drain
Connect the drain hose form to the drain hose at the...
User Guide - Page 16
... the drain hose into standpipe. SECURE THE DRAIN HOSE
1. See illustrations A and B. If the washer faucets and the drain standpipe are not tight against the washer cabinet. LEVEL THE WASHER
One foot has been installed at the factory. See Floor Drain under "Tools and Parts."
NOTES:
• Do not force excess drain hose back into the rear of the drain hose in the laundry...
User Guide - Page 22
... in mesh garment bags. It is helpful when you do not select START within 5 minutes of suds for a medium-sized load. The washer door will illuminate. Open the dispenser drawer and add laundry additives to select ON or OFF.
7. See "Options."
6. The signal is recommended that more than one of sorted clothes in...
User Guide - Page 24
...60 mL) liquid fabric softener to your load.
• Always measure liquid chlorine bleach. Select and hold START (for approximately 1 second) to begin the drain.
4. Select and hold START (for...START (for approximately 1 second).
To stop a cycle and select a new cycle
1. To drain the washer manually
1. Items can be changed anytime before the door unlocks.
Use a measuring cup with ...
User Guide - Page 31
..., you will not freeze. To use abrasive products.
VACATION, STORAGE, & MOVING CARE
Install and store your washer where it . Unplug washer or disconnect power.
4. Remove the inserts (the siphon from faucets and drain.
WATER INLET HOSES
Replace inlet hoses after each cycle to allow the cycle to the drawer.
If storing or moving your inlet...
User Guide - Page 32
... 1/2 the manufacturer's recommended amount for a medium sized load.
3-14 Unplug the power cord.
3. Disconnect the water inlet hoses from the drain system and attach to rear panel clips.
4. Do not use an adapter. If washer will be transported in the upright position. Disconnect the drain hose from faucets, then drain the hoses and clip them to clean the...
User Guide - Page 33
... pedestal feet must be shown in firm contact with metal snaps, buckles or zippers? Check the following : Is the drain hose kinked, frozen, clogged, or more than 96˝ (2.4 m) above the floor?
• Is washer installed on a pedestal, the washer must be secured to . Are screens at equal heights.
• Is the...
User Guide - Page 34
..., drainpipe, water pipes) for details.
• Are the laundry additives in the washer. See "Washer Care" for leaks. The washer door will unlock.
3-16 Add the correct amounts of the washer during "Add a garment"? See "Secure the Drain Hose."
• Is the sink or drain clogged? To freshen your washer and to the dispensers? Check both ends of the...
User Guide - Page 35
...) above the floor?
• Is the voltage low? WASHER CONTINUES TO FILL OR DRAIN, DRAIN CYCLE SEEMS STUCK
• Is the top of the drain hose more items or redistribute the load. WASHER WON'T DRAIN OR SPIN, WATER REMAINS IN WASHER
• Is the drain hose clogged, or the end of drain hose lower than 96˝ (2.4 m) above the floor. NOT...
User Guide - Page 36
... will start a Drain/Spin cycle. WASH / RINSE TEMPERATURE
• Are the hot and cold water inlet hoses reversed? The SUDs...;ciency detergent. As your wet laundry in a gentle or Delicate cycle? The options you add detergent to the washer drum.
• Did you...Did you overload the washer? Use HE detergent. See "Connect the Inlet Hoses."
• Are you wash a large load in the drum, and...
User Guide - Page 55
... pad, and slide the pump to the washer. 3. Pump-To-Tub Hose
Tab Arrow
Tabs
Pump-ToDrain Hose
1.
Drain Pump Filter
4-17
Lift Rubber Pad
Tab
Continued on the next page. REMOVING THE DRAIN PUMP
5. Loosen the clamp and remove the pumpto-drain hose from the pump. Unplug washer or disconnect power. 2. Drain Pump
4. Turn off the water supply...
User Guide - Page 80
.../Procedure The relay might be displayed. Possible Causes/Procedure 1. Check the drain hose and make sure
the pump is out of the WASH cycle. Check the drain pump filter for foreign objects. 5. Replace the pump.
Check resistance of the main relays is in washer or reconnect power. 6. Check the water temperature sensor and connection...
User Guide - Page 81
...Check the drain hose and make sure it is not plugged or
kinked.
2. Check for proper operation. Check the pressure switch for drain pump failure.
6. Unplug washer or disconnect power.
2. Plug in washer or reconnect...motor, the MCU will communicate this failure to the top
of the CLEANING WASHER cycle a load is cleared. Plug in washer or reconnect power. 4. Refer to the MCU, the motor,
and ...
User Guide - Page 82
... foreign objects. 5. Run the unit through a RINSE/SPIN cycle. - Check/clean drain pump filter of the excess detergent.
1. Check the pressure switch. 8.
Check the drain hose and make sure it will rest without adding any
cycle. Unplug washer or disconnect power. 3. Plug in washer or reconnect power. 6. Failure Codes
Status LEDs
Duet Sport
Duet Sport...
User Guide - Page 89
...
any cycle.
1. Press PAUSE/CANCEL on the touchpad twice.
3. Unplug washer or disconnect power.
5. Drain the unit, then check that the drain hose and drain pump filter are clear of line cord and line filter.
5. Check water connections to CCU.
6. Check that the drain hose and drain
SELECTIONS
pump filter are clear of the
drive motor.
6-11 CONTROL...
User Guide - Page 90
... power. 2. Check installation. 3. Check that the drain hose and drain pump filter are connected properly.
2. Unplug washer or disconnect power.
3. Check drain pump motor. 5.
INCORRECT WATER TEMPERATURE
1. Verify CCU operation by running a Diagnostic Test or any cycle. Check wire harness connections. 3. Plug in washer or reconnect power.
6. Verify CCU operation by...
Similar Questions
What Is The Purpose Of Running A Diagnostic Test On Kenmore Front Load Washer
(Posted by dabawa 10 years ago)
Kenmore He2t Front Loading Washer Model# 110.4756
When I turn power on the front panel lights up, but when I push start it all shuts down. Tried unplu...
When I turn power on the front panel lights up, but when I push start it all shuts down. Tried unplu...
(Posted by cpcalder 11 years ago)
What Does It Mean When A Kenmore Front Load Washer Model # 48102 Turns Off And O
what does it mean when a kenmore front load washer model # 48102 turns off and on during the washing...
what does it mean when a kenmore front load washer model # 48102 turns off and on during the washing...
(Posted by kemackey86 11 years ago)
Why Front Load Washer 4044 Won't Start The Cycle?
Yesterday while my front load washer 4044 was starting to do its first normal cycle , which usually ...
Yesterday while my front load washer 4044 was starting to do its first normal cycle , which usually ...
(Posted by martinezmarly 11 years ago)
Does This Front Load Washer Need To Have Bolts Installed To Move From Another St
model#110.47571602 HE2t frontload washer locking bolts for moving?
model#110.47571602 HE2t frontload washer locking bolts for moving?
(Posted by donnasilver 12 years ago)