Honeywell RTH2310 Support Question
Honeywell RTH2310 Support Question
Find answers below for this question about Honeywell RTH2310.Need a Honeywell RTH2310 manual? We have 1 online manual for this item!
Question posted by garywhiteman on June 14th, 2014
Display Goes Blank
twice the display has gone blank then come back on when i press keys. both times needed to reset the time but program still in place. no low battery warning on display. ran a/c overnight down to 59deg first time 3wks ago. yesterday just noticed it was blank while walking past. unit 2yrs old. don't trust it anymore, what's wrong?
Current Answers
Related Honeywell RTH2310 Manual Pages
Owner's Manual - Page 1
Quick Installation Guide
RTH2310
Programmable Thermostat 69-2214EF-02
Owner's Manual - Page 2
... are here to help. Just follow the simple step-by-step instructions in the following pages.
Identify your system type. Remove your old thermostat. Identify the wires. Mount the new wallplate. Connect the wires. If the wire labels don't match. Specify the furnace type...
Owner's Manual - Page 3
RTH2310 Programmable Thermostat
Identify System Type
1. This thermostat is compatible with the following systems:
• Gas, oil or electric furnace • Central air conditioner • a hot water system with heat pumps or multi-stage systems.
2 This thermostat is not compatible with or without pump • a millivolt system • a central heating and cooling system
If...
Owner's Manual - Page 4
... not put your local waste management authority for instructions regarding recycling and proper disposal.
3 Do not remove wallplate yet. Quick Installation Guide
Remove Old Thermostat
2.
1) Turn power off at the heating/cooling system.
2) Remove old thermostat, but leave wallplate with wires attached.
Owner's Manual - Page 5
...Identify and label each of each wire.
If any wires are not attached to your old thermostat or are labeled.
Disconnect wires and remove the old wallplate only after all wires are attached...to a terminal marked C or C1, they will not be connected to your new thermostat. IGNORE WIRE COLORS: Use terminal screw designations to prevent them from falling though the wall opening...
Owner's Manual - Page 6
Pass wires through opening of wallplate and secure wallplate to the wall using provided screws.
5 Insert plastic anchors. Quick Installation Guide
Mount New Wallplate
4.
1) Remove coverplate.
2) Loosen screw (the screw remains captive on wallplate).
3) Remove thermostat.
4) Mark and drill appropriate mounting holes (or use existing holes).
Owner's Manual - Page 7
... with the terminal having the same letter.
2) Loosen the terminal screws using a screwdriver, insert the wires, then tighten the screws.
3) Push any terminal on the thermostat, see next page.
6 RTH2310 Programmable Thermostat
Connect Wires (typical wiring) 5.
Owner's Manual - Page 9
Set the Jumper J2, on the back of the thermostat, if you have an electric furnace.
8 RTH2310 Programmable Thermostat
Specify Furnace Type
6.
J2 jumper
HG Leave the jumper in this factory-set position if you have connected a wire to this position if you have a gas or oil furnace. HE Place the jumper to the G terminal.
Owner's Manual - Page 10
Observe the
polarity. 3) Reinstall the battery cover. The thermostat will hear a clicking
sound. Quick Installation Guide
Install Batteries
7.
1) Pull out the battery cover. 2) Install the batteries as shown. Afterwards, the screen displays the actual temperature. By default, the setpoint is normal that the displayed temperature be higher than the ambient temperature if you are...
Owner's Manual - Page 11
RTH2310 Programmable Thermostat
Install thermostat
8.
1) Mount the thermostat on the wallplate.
2) Tighten the screw and install the coverplate.
3) Turn power back on at the heating/cooling system.
10
Owner's Manual - Page 12
DISPLAY
DESCRIPTION
OPTIONS 1
Temperature display
°C or °F
Time display
12 h or 24 h
Early Start 2
On or Off
Heating cycles per hour 3
2, 3, 4, 5 or...To advance to the next function, briefly press both and buttons simultaneously.
3) To change the setting, press the or button. Quick Installation Guide
System Setup
9.
1) Press both and buttons simultaneously for gas or...
Owner's Manual - Page 13
Guide d'installation rapide
RTH2310
Thermostat programmable 69-2214EF-02
Similar Questions
How Do You Reset A Honeywell Thermostat Model Number Rth2310
(Posted by mietsacre 9 years ago)
Nearly Blank Screen
My Honeywell screen is fading, we've changed batteries still nearly blank screen, think the model is...
My Honeywell screen is fading, we've changed batteries still nearly blank screen, think the model is...
(Posted by Karenanderson1234 10 years ago)
Rth230b When Switched To Heat, Display Goes Blank
(Posted by chickiwak 10 years ago)
I Have A T8600d 2028. It Goes Blank And Looses Set Time. There Are No Batteries
(Posted by wjenk 11 years ago)