Honeywell RTH2310 Support Question
Honeywell RTH2310 Support Question
Find answers below for this question about Honeywell RTH2310.Need a Honeywell RTH2310 manual? We have 1 online manual for this item!
Question posted by mietsacre on August 11th, 2014
How Do You Reset A Honeywell Thermostat Model Number Rth2310
The person who posted this question about this Honeywell product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Answer #1: Posted by BusterDoogen on August 24th, 2014 12:29 PM
BusterDoogen
Member since:
October 30th, 2011 Points: 28,565,407
Member since:
October 30th, 2011 Points: 28,565,407
After 500 hours of heating or cooling time, an icon appears to indicate that the filter needs replacement. Once the filter is replaced, press the Filter button for 3 seconds to remove the icon and reset the counter.
I hope this is helpful to you!
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful. Please feel free to submit further info for your question, if a solution was not provided. I appreciate the opportunity to serve you
Related Honeywell RTH2310 Manual Pages
Owner's Manual - Page 1
Quick Installation Guide
RTH2310
Programmable Thermostat 69-2214EF-02
Owner's Manual - Page 2
...-step instructions in the following pages.
Identify your system type. Remove your old thermostat. Identify the wires. Mount the new wallplate. Connect the wires. ... the furnace type. Install the batteries. Install the thermostat. Set the system. Call 1-800-468-1502.
1 Do you need assistance? Quick Installation Guide
...
Owner's Manual - Page 3
... systems:
• Gas, oil or electric furnace • Central air conditioner • a hot water system with heat pumps or multi-stage systems.
2 RTH2310 Programmable Thermostat
Identify System Type
1. This thermostat is not compatible with or without pump • a millivolt system • a central heating and cooling system
If you are not sure of...
Owner's Manual - Page 4
... waste management authority for instructions regarding recycling and proper disposal.
3 Contact your old thermostat in the trash if it contains mercury in a sealed tube.
Quick Installation Guide
Remove Old Thermostat
2.
1) Turn power off at the heating/cooling system.
2) Remove old thermostat, but leave wallplate with wires attached. Do not remove wallplate yet.
Owner's Manual - Page 5
... opening.
4 Do not use C or C1 wires
Identify and label each of these wires with electrical tape, so it cannot touch and short other wires.
RTH2310 Programmable Thermostat
Identify Wires
3. Disconnect wires and remove the old wallplate only after all wires are attached to a terminal marked C or C1, they will not...
Owner's Manual - Page 6
Pass wires through opening of wallplate and secure wallplate to the wall using provided screws.
5 Insert plastic anchors. Quick Installation Guide
Mount New Wallplate
4.
1) Remove coverplate.
2) Loosen screw (the screw remains captive on wallplate).
3) Remove thermostat.
4) Mark and drill appropriate mounting holes (or use existing holes).
Owner's Manual - Page 7
... with the terminal having the same letter.
2) Loosen the terminal screws using a screwdriver, insert the wires, then tighten the screws.
3) Push any terminal on the thermostat, see next page.
6
RTH2310 Programmable Thermostat
Connect Wires (typical wiring) 5.
Owner's Manual - Page 9
HE Place the jumper to the G terminal.
J2 jumper
HG Leave the jumper in this position if you have an electric furnace.
8 Set the Jumper J2, on the back of the thermostat, if you have connected a wire to this factory-set position if you have a gas or oil furnace. RTH2310 Programmable Thermostat
Specify Furnace Type
6.
Owner's Manual - Page 10
... ambient temperature once it is normal that the displayed temperature be higher than the ambient temperature if you are installed, the thermostat performs a series of tests for approximately 5 seconds. The thermostat will hear a clicking
sound. It is installed on the wall. Quick Installation Guide
Install Batteries
7.
1) Pull out the battery cover...
Owner's Manual - Page 11
RTH2310 Programmable Thermostat
Install thermostat
8.
1) Mount the thermostat on the wallplate.
2) Tighten the screw and install the coverplate.
3) Turn power back on at the heating/cooling system.
10
Owner's Manual - Page 13
Guide d'installation rapide
RTH2310
Thermostat programmable 69-2214EF-02
Similar Questions
How To Factory Reset My Honeywell Thermostat Model Number Th4110d1007
(Posted by Jeremygsons 9 years ago)
How To Reset My Honeywell Thermostat Model Number Th5220d1003
(Posted by pebdoug 9 years ago)
Can't Get Heater System To Stay On (rth2310),
thermostat was preset by old owner, can't figure out how to reset it.
thermostat was preset by old owner, can't figure out how to reset it.
(Posted by eladio62 10 years ago)
How To Wire Rth2310 To An Oil Fired Boiler?
I have an oil fired boiler with three zones. I am trying to install RTH2310 Stats to control each zo...
I have an oil fired boiler with three zones. I am trying to install RTH2310 Stats to control each zo...
(Posted by Grayai 12 years ago)