Honeywell RTH2310 Support Question
Honeywell RTH2310 Support Question
Find answers below for this question about Honeywell RTH2310.Need a Honeywell RTH2310 manual? We have 1 online manual for this item!
Question posted by Karenanderson1234 on September 8th, 2013
Nearly Blank Screen
My Honeywell screen is fading, we've changed batteries still nearly blank screen, think the model is cms921b1042, can anyone help please?
Current Answers
Answer #1: Posted by TommyKervz on September 8th, 2013 6:30 AM
TommyKervz
Member since:
January 10th, 2013 Points: 17,776,813
Member since:
January 10th, 2013 Points: 17,776,813
Greetings - It sounds like a bad thermostat.
Related Honeywell RTH2310 Manual Pages
Owner's Manual - Page 1
Quick Installation Guide
RTH2310
Programmable Thermostat 69-2214EF-02
Owner's Manual - Page 2
...; Mount the new wallplate. Connect the wires. If the wire labels don't match. Specify the furnace type. Install the batteries. Install the thermostat. Set the system. We are here to help. Call 1-800-468-1502.
1 Do you need assistance? Quick Installation Guide
Installation is Easy
Your new...
Owner's Manual - Page 3
RTH2310 Programmable Thermostat
Identify System Type
1.
This thermostat is compatible with the following systems:
• Gas, oil or electric furnace • Central air conditioner • a hot water system with heat pumps or multi-stage systems.
2 This thermostat is not compatible with or without pump • a millivolt system • a central heating and cooling system
...
Owner's Manual - Page 4
Do not remove wallplate yet. Quick Installation Guide
Remove Old Thermostat
2.
1) Turn power off at the heating/cooling system.
2) Remove old thermostat, but leave wallplate with wires attached.
Contact your old thermostat in the trash if it contains mercury in a sealed tube. MERCURY NOTICE: Do not put your local waste management authority for...
Owner's Manual - Page 5
...wires are attached to a terminal marked C or C1, they will not be connected to your old thermostat or are labeled. Wrap the bare metal end of each wire. IGNORE WIRE COLORS: Use terminal screw ...Wrap the wires around a pencil to identify wires. If any wires are not attached to your new thermostat. Do not use C or C1 wires
Identify and label each of these wires with electrical tape, so ...
Owner's Manual - Page 6
Insert plastic anchors. Pass wires through opening of wallplate and secure wallplate to the wall using provided screws.
5 Quick Installation Guide
Mount New Wallplate
4.
1) Remove coverplate.
2) Loosen screw (the screw remains captive on wallplate).
3) Remove thermostat.
4) Mark and drill appropriate mounting holes (or use existing holes).
Owner's Manual - Page 7
If a wire does not match any excess wire back into the wall opening. Labels don't match? RTH2310 Programmable Thermostat
Connect Wires (typical wiring) 5. Remove jumper if you have both R and Rc wires.
1) Match each labeled wire with the terminal having the same letter.
2) ...
Owner's Manual - Page 9
HE Place the jumper to the G terminal.
Set the Jumper J2, on the back of the thermostat, if you have connected a wire to this factory-set position if you have a gas or oil furnace. J2 jumper
HG Leave the jumper in this position if you have an electric furnace.
8 RTH2310 Programmable Thermostat
Specify Furnace Type
6.
Owner's Manual - Page 10
... the wall. Afterwards, the screen displays the actual temperature. The thermostat will hear a clicking
sound. By default, the setpoint is 70 °F (21 °C).
9 Observe the
polarity. 3) Reinstall the battery cover. After the batteries are holding the thermostat. Quick Installation Guide
Install Batteries
7.
1) Pull out the battery cover. 2) Install the batteries as shown.
Owner's Manual - Page 11
RTH2310 Programmable Thermostat
Install thermostat
8.
1) Mount the thermostat on the wallplate.
2) Tighten the screw and install the coverplate.
3) Turn power back on at the heating/cooling system.
10
Owner's Manual - Page 12
Quick Installation Guide
System Setup
9.
1) Press both and buttons simultaneously.
3) To change the setting, press the or button. DISPLAY
DESCRIPTION
OPTIONS 1
Temperature display
°C or °F
Time display
12 h or 24 h
Early Start 2
On or Off
Heating ...
Owner's Manual - Page 13
Guide d'installation rapide
RTH2310
Thermostat programmable 69-2214EF-02
Similar Questions
How Do You Reset A Honeywell Thermostat Model Number Rth2310
(Posted by mietsacre 9 years ago)
Screen On Touchscreen Thermostat Has Ee. Changed Battery And Flicked Circuit Bre
breaker but will not work. What to do? Model GH8320U1008
breaker but will not work. What to do? Model GH8320U1008
(Posted by ljones5706 10 years ago)
Display Screen Is Blank After Changing Batteries
The display screen showed LO which we took to mean the batteries were low even though the manual doe...
The display screen showed LO which we took to mean the batteries were low even though the manual doe...
(Posted by bhugg137 12 years ago)
How To Wire Rth2310 To An Oil Fired Boiler?
I have an oil fired boiler with three zones. I am trying to install RTH2310 Stats to control each zo...
I have an oil fired boiler with three zones. I am trying to install RTH2310 Stats to control each zo...
(Posted by Grayai 12 years ago)