Home » Frigidaire » Ice Machines » Frigidaire IM115

Frigidaire IM115 Support Question

Find answers below for this question about Frigidaire IM115 - Ice Maker Kit.
Need a Frigidaire IM115 manual? We have 1 online manual for this item!

Frigidaire Overview Questions Manuals Reviews Videos Research

Question posted by glera on June 20th, 2014

How Long Should It Take For Ice Maker To Make Batch Of Ice

The person who posted this question about this Frigidaire product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.

Requests for more information

Request from OnlineOutreachSpecialist on June 26th, 2014 11:28 AM
Good Afternoon Glera,

I understand you want to know how long it should take for a batch of ice to be made in your ice maker, model# IM115. I will be more than happy to assist you. So I am able to better assist you, I kindly ask for the model number of your refrigerator, which the ice maker is attached to. You can typically find this number located inside your refrigerator, on the side walls. Looking forward to hearing from you.

-Best Regards-

I Know the Answer!

I have the same question
Request More Information

Current Answers

There are currently no answers that have been posted for this question.
Be the first to post an answer!

Remember that you can earn up to 1,100 points for every answer you submit. The better the quality of your answer, the better chance it has to be accepted.

Related Frigidaire IM115 Manual Pages

User Manual - Page 1

...; 1/4 inch brass compression nut and ferrule • Freezer shelf (Some models not eqipped with shelf). The following items will not be required to install the ice maker kit. • 1/4 inch copper supply line with shut off valve are available in areas where temperatures fall below freezing. • Connect the...

User Manual - Page 2

... - Qty 1 Tools Required: • Putty Knife • ¼ inch Socket Wrench or Nut Driver • Knife • Pliers • Needle Nose Pliers • Adjustable Wrench 2 Ice Maker 2. Leveling Bracket Qty 1 8. Qty 2 10. Ice Container 3. Plastic Water Supply Tubing 4. Qty 2 5. Qty 1 9.

User Manual - Page 3

...lift up and pull on back of refrigerator. Peel off label covering ice maker hole. 7. Rotate while inserting tube until right side of shelf is... screw(s). Remove freezer shelf (some models). 3. Remove and save screws. Unplug refrigerator from hole. 5. Remove ice tray rack from inside compressor compartment (D), remove screws securing sound baffle to remove. 4. Remove plugs from freezer ...

User Manual - Page 4

... tighten bracket. (Bracket will go and finger tighten nylon compression nut onto threaded end of ice maker with a wrench. Start two, long, ice maker mounting screws (5) into water inlet tube (11) as far as it will be tightened later.) 13. 9. Make sure water inlet tube (11) is sitting inside fill cup. 11. Turn each screw five...

User Manual - Page 5

...models with factory drilled holes. Connect wiring harness to drive the two self drilling screws (4) through cabinet liner. Set ice container (2) on shelf. 18. Align water valve bracket with exterior condenser, reinstall condenser brackets and tighten down screws. ...19. Use a power drill with a Phillips® head bit to water valve. Make sure connection is tight. 20. See step 5. 5

User Manual - Page 6

... or three times before connecting a water supply line to the ice maker inlet valve. IMPORTANT: Ensure that your household water system. Disconnect...kit number 5303917950, available from electrical power before making a full tray of water supply line into valve inlet and finger tighten compression nut onto valve.Tighten another half turn ice maker on, lower wire signal arm. (See ice maker...

User Manual - Page 7

.... • Keep the wire signal arm in its “down” or ON position. If your ice quality. Ice Maker Tips • Ice stored too long may develop an odd flavor. The ice maker will then produce more ice. • Occasionally shake the container to the water supply or whenever the water supply is turned off. • The...