Frigidaire IM115 Support Question
Frigidaire IM115 Support Question
Find answers below for this question about Frigidaire IM115 - Ice Maker Kit.Need a Frigidaire IM115 manual? We have 1 online manual for this item!
Question posted by majoAsim on February 16th, 2014
How Long Does It Take Ice Maker To Make Batch Of Ice
The person who posted this question about this Frigidaire product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Frigidaire IM115 Manual Pages
User Manual - Page 1
...for the supply line. • DO NOT install water supply tubing in a kit from the softener may damage the ice maker, causing it greatly increases the potential for water leaks.
Water supply tubing made ... plumbing supply store.
The following items will not be required to install the ice maker kit. • 1/4 inch copper supply line with shut off valve are available in areas where temperatures ...
User Manual - Page 2
...; Knife
• Pliers • Needle Nose Pliers • Adjustable Wrench
2 Qty 2
5. Qty 1
11. Qty 2
6. Water Valve - Qty 2
10. Screws - Use This Page to Identify Parts
1. Ice Maker
2. Screws - Steel Clamp -
User Manual - Page 3
... rack from inside compressor compartment (D), remove screws securing sound baffle to remove.
4. Remove freezer shelf (some models).
3. Peel off label covering ice maker hole.
7. Rotate while inserting tube until right side of shelf is out of refrigerator.
3 DO NOT remove compressor sound baffle (A), if installed.Carefully bend condenser ...
User Manual - Page 4
... bracket (7) on back freezer panel. Ice maker is level when gap between freezer wall and ice maker is sitting inside fill cup.
11. Mount ice maker onto two screws (5) you installed in one half turn with screw (6). Make sure water inlet tube (11) is same at top and bottom. Start two, long, ice maker mounting screws (5) into water inlet tube...
User Manual - Page 5
Locate factory punched holes at bottom right corner of water valve. Make sure connection is tight.
20. Finger tighten nylon compression nut onto ... clamps.
17. 15. Tighten another one half turn with dynamic condensers, remount sound baffle, if installed. Set ice container (2) on shelf.
18. DO NOT over tighten.
16.
Reinstall freezer shelf in lower position. Push plastic water supply...
User Manual - Page 6
...rear panel of 1/4 inch (6.4 mm) OD, copper tubing. NOTE: Water line kit number 5303917950, available from your household water system. Disconnect refrigerator from water valve inlet...ice maker to your appliance dealer at shutoff valve and tighten any other surface.
8. New plumbing may damage the ice maker, causing it will need to measure the distance from electrical power before making...
User Manual - Page 7
... water • Water valve opening or closing
DO NOT place the ice container in your dishwasher. • Wash ice container in its “up ” or OFF position. Ice Maker Tips • Ice stored too long may develop an odd flavor.
The ice maker will then produce more ice. • Occasionally shake the container to the water supply or...
Similar Questions
How Long Should It Take For Ice Maker To Make Batch Of Ice
(Posted by glera 9 years ago)
How Long For Ice Maker Im115 To Make Ice
(Posted by Anabeaye 10 years ago)
How To Install Ice Maker Kit Im115
(Posted by mikmDaniel 10 years ago)
Space Dimension Requirements For Frigidaire Complete Ice Maker Kit Im-501?
I plan to install an ice maker in a small upright freezer. I need the dimension requirements for th...
I plan to install an ice maker in a small upright freezer. I need the dimension requirements for th...
(Posted by dan1b 12 years ago)